Parts for Ge AZ65H07DABW2: Motor & Chassis Parts

Plastic coupler that connects shroud sections on your room air conditioner. Replace if cracked, broken, or missing to secure the outer cabinet.

This replacement fan shroud clip fastens the outer fan shroud to the appliance frame, helping keep the fan assembly secure and aligned for proper airflow. It's a small but necessary part for stable fan operation. What it does

• Secures the outer fan shroud to the dryer/refrigerator cabinet to hold the fan assembly in position
• Helps prevent fan wobble and rubbing that can cause noise or premature wear
• Maintains proper airflow path for cooling or exhaust systems
• Useful when an original clip is cracked, bent or missing

• One fan shroud clip

• Disconnect power (and gas, if applicable) before beginning any repair
• Access may require removing a rear or lower panel; keep track of fasteners and orientation
• Inspect surrounding shroud and fan for damage while replacing the clip

Fix rattling noise or sluggish fan operation in your room air conditioner with this DC fan motor. Direct replacement for improved efficiency and quiet.

5/16" shoulder screw secures panels and internal components in room air conditioners. Replace if rusted, corroded, stripped, or missing threads.

Replacement 10-32 hex nut for room air conditioner assemblies. Secures panels, brackets, and components. Needed when original nut is lost or stripped.

AC not cooling or overheating? This outdoor fan assembly circulates air across the condenser coil to expel heat and restore proper cooling performance.

Air conditioner won't heat or fan speed stuck? This silicon controlled rectifier regulates power output to restore proper voltage control and operation.

This U-nut secures panels and trim to sheet-metal flanges and studs, providing a threaded attachment point for screws on 10–16 gauge material. It helps restore solid, rattle-free connections and reliable fastener engagement. What it does:

• Provides a captive, threaded insert for machine or sheet-metal screws on thin metal flanges
• Restores or replaces stripped, missing, or damaged panel mounting points
• Helps stop loose panels, vibration noise, and misaligned trim caused by missing fasteners
• Designed for use where a 10–16 screw size and hi/lo flange thickness is required

• Verify correct location and flange thickness before installing; part is sized for 10–16 fasteners and hi/lo flange profiles
• Slide onto flange or stud until fully seated, then fasten with the specified screw; avoid forcing or deforming the clip
• Use hand tools and proper screw size; do not overtighten to prevent stripping the nut or damaging the panel
• Disconnect power and follow manufacturer service instructions when accessing internal appliance areas

This bulkhead wire cover protects and secures the appliance's wiring at the bulkhead, keeping harnesses organized and reducing risk of chafing or accidental contact. It helps maintain safe, reliable connections behind the access panel. What it does:

• Covers and shields the wire harness where it passes the bulkhead or panel
• Keeps wiring routed and retained to prevent rubbing against sharp edges
• Helps reduce noise from loose harnesses and prevents snagging during service
• Supports safer access to terminals by keeping wires contained

• Disconnect power (unplug or shut off breaker) before servicing
• Access may require removing the front or rear access panel — keep fasteners safe
• Seat the harness fully before snapping or fastening the cover; do not force parts
• If wiring or insulation looks damaged, replace the wiring/harness per service manual rather than relying on the cover

Replacement grommet for room air conditioners. Installs to cushion and seal components. Order a new one if your original is cracked, worn, or missing.

This right-side wire cover protects and secures wiring inside the appliance to prevent chafing and accidental contact with hot or moving parts. It helps keep wiring routed neatly for reliable, safe operation. What it does:

• Shields wiring from heat, abrasion, and pinch points on the right side of the cabinet
• Keeps wire bundles routed and restrained to prevent interference with components
• Reduces risk of shorts or intermittent connections caused by damaged insulation
• Common symptom: visible or frayed wires, sparks, intermittent power, or blown fuses

• One right-side wire cover

• Disconnect power (unplug or shut off breaker) before starting any repair
• Replace like-for-like using existing mounting points and hardware; do not bend or force the part
• Inspect adjacent wiring and insulation; replace any damaged wires or clips as needed

Air conditioner not blowing air or making unusual noises? This indoor fan motor kit circulates air throughout your room. Connects via plug-in harness.

AC not cooling or no airflow? The indoor fan blade circulates cooled air into your room. Simple DIY replacement—unplug, remove front panel and cover.

Supports and centers the blower shaft in your room air conditioner's indoor fan assembly. Replace when you notice excessive noise or vibration. Confirm fit with your model number before ordering.

Fix an air conditioner that won't heat with a new heater assembly. Common cause when unit switches to heat mode but produces no warm air.

A replacement rod vent door that restores the exhaust vent barrier for proper airflow and helps keep pests and debris out when the appliance is off. Fits the vent assembly where a small hinged door is required. What it does:

• Replaces a worn, bent or broken vent door to restore proper opening and closing of the vent
• Helps prevent backdrafts, dust and small pests from entering the appliance through the vent
• Stops noisy rattling or scraping caused by a loose or damaged vent door
• Restores a secure seal so the vent functions as intended during operation

• Disconnect power to the appliance before starting any repair
• Inspect surrounding hinge/rod and mounting tabs; replace any damaged hardware
• Align the door on the rod and test open/close movement before reassembly

This 11-piece wall sleeve gasket kit provides replacement foam seals that help restore a snug seal around the dryer vent wall sleeve, reducing drafts, rattles and moisture infiltration for better performance and quieter operation. What it does:

• Replaces worn or missing foam gasket pieces around the wall sleeve to improve the seal between the dryer vent and the wall.
• Helps reduce air leaks and drafts that can lower dryer efficiency or bring cold air into the home.
• Cushions the sleeve to reduce vibration and rattling during operation.
• Minimizes gaps that can allow lint, dust or small pests into the wall cavity.

• Disconnect power and ensure the dryer and vent are cool before beginning work.
• Remove the dryer and wall sleeve trim as needed, clean mating surfaces, and confirm correct placement of each gasket piece.
• Use only manufacturer-recommended fasteners or adhesive if required; verify orientation and fit before final reassembly.