Parts for Kenmore 795.79412810 (79579412810, 795 79412810): Other Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This leveling leg assembly stabilizes and levels your refrigerator so it sits solidly on the floor and the doors align correctly. Replacing a worn or stripped leg helps reduce rocking and vibration and restores smooth leveling adjustment.

• Provides height adjustment to level the cabinet on uneven floors
• Supports the unit to prevent rocking or wobbling
• Helps doors close and seal properly when the cabinet is level
• Symptoms may include persistent wobble, vibration/rattling, or a stripped/bent foot or screw

• Unplug the refrigerator and use a helper to prevent tipping injuries.
• Protect flooring; remove the kickplate/grille for access if present.
• Thread out the worn leg; hand-thread the new assembly and adjust height—do not over-extend.
• Level side-to-side and front-to-back per your owner's manual, then reattach any panels.

This is the ice bucket that stores ice dispensed by your refrigerator's ice maker. A cracked, warped, or stuck bin can jam the auger or spill ice, leading to poor dispensing and messy freezers.

• Holds and dispenses harvested ice from the ice maker to the door chute or bin access
• Common failure signs: cracked bucket, ice not dispensing, auger not turning, ice clumping or spilling
• Restores smooth ice dispensing and proper storage in the freezer
• Built to fit the original mounting and drive interface for an easy swap

• Unplug the refrigerator and wear cut-resistant gloves
• Remove the old bin carefully; thaw any ice buildup before transferring
• Inspect the auger drive coupling for wear before installing the new bucket
• Seat the bucket fully so the drive engages; test dispense with a small amount of ice

This roller is the small wheel that lets a sliding component move smoothly along its track. Replacing a worn or cracked roller restores easy, quiet operation and helps prevent binding, noise, and uneven travel.

• Supports and guides a moving bin, drawer, or rack on its track
• Reduces friction for smooth, even motion
• Common symptoms: sticking or hard-to-open movement, grinding/clicking noises, wobbling/misalignment, or a cracked/missing wheel
• Helps protect tracks and brackets from excess wear

• Disconnect power before servicing; wear gloves to protect hands
• Remove the sliding component to access the roller
• Release the clip/fastener, install the new roller, and transfer/reuse original hardware if applicable
• Test movement to ensure the roller is fully seated and tracking correctly; replace in pairs when applicable for even travel

Roller assembly approx. 1".

Roller assembly approx. 2".

Restore a sturdy, clean storage surface inside your refrigerator with this replacement drawer tray. It replaces a cracked or missing tray so food stays organized and the drawer fits and functions as intended. What it does:

• Provides the flat base/support for a refrigerator storage drawer
• Helps keep food organized and prevents items from tipping or falling
• Maintains proper fit and alignment of the drawer within the compartment
• Common symptoms: cracks, broken tabs, warping, drawer not sitting level or sliding smoothly

• 1 drawer tray

• Empty and remove the drawer before replacing the tray
• Align and seat the new tray fully in the guides; ensure it is level before reloading
• Transfer any reusable hardware from the old tray if applicable
• Handle plastic carefully to avoid stress cracks; do not force into place

This rail holder secures the microwave door rail so the door stays aligned and operates smoothly. Replaces a worn or broken holder to reduce door wobble and improve closing action. What it does:

• Secures and supports the door rail assembly for proper door alignment
• Keeps the rail from shifting, preventing rubbing, rattling or uneven gaps
• Helps restore smooth opening and closing of the door
• Fits where the rail mounts to the door frame or trim

• One rail holder

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools (screwdriver/trim tool) and handle plastic parts gently to avoid breakage
• Inspect surrounding clips/rails for damage and replace if needed for a lasting repair

This rail holder is the replacement support that secures an appliance rail in place, restoring proper alignment and smooth movement. It helps keep sliding components stable so drawers or rails track correctly and safely. What it does:

• Secures the rail or slide to the appliance frame to prevent sagging or misalignment
• Restores smooth, controlled movement of sliding parts
• Helps eliminate rattling, binding or uneven travel caused by a loose or broken holder
• Works as a direct-fit support when the original holder is damaged or worn

• Disconnect power and remove any movable components before beginning work
• Installation typically requires basic hand tools; keep fasteners from the original part for reuse if undamaged
• Inspect adjoining rails, slides and mounting points; replace any damaged hardware for best results

A replacement glide rail assembly that supports and guides a refrigerator/freezer drawer for smooth opening and closing. Restores proper drawer tracking and helps prevent sticking or misalignment. What it does:

• Provides the rail and mounting components that the drawer slides on for stable operation
• Restores smooth drawer movement and alignment when original rail is bent or worn
• Helps reduce drawer sticking, scraping, or uneven travel
• Intended for use where the OEM glide/rail assembly is specified

• One glide rail assembly

• Follow the appliance manufacturer's service manual for removal and installation steps
• Disconnect power and empty the drawer before working to prevent injury or damage
• Inspect mounting hardware and drawer slides; replace any damaged fasteners
• Use basic hand tools;

This genuine replacement knob shutter restores the control panel's knob opening and protects internal switches from debris while allowing knobs to engage properly. It helps maintain smooth knob operation and reduces dirt buildup behind the control surface. What it does:

• Covers the knob opening and guides the control knob into place for reliable engagement
• Protects internal switches and electronics from dust, crumbs, and spills
• Helps prevent accidental knob movement when not in use
• Restores proper fit and appearance of the control panel area

• One knob shutter

• Power off and unplug the appliance before beginning any work to avoid electrical shock
• Small fasteners or clips may need to be removed; use appropriate hand tools and keep track of hardware

Replace a cracked or missing produce bin so fruits and vegetables store at the proper humidity and your fridge stays organized. This direct-fit crisper drawer restores clean, reliable storage in the fresh-food section.

What it does

• Stores produce at a humidity level intended for fruits and vegetables
• Restores smooth pull-out/push-in operation when paired with intact slides
• Helps prevent spills and items dropping behind the drawers
• Replaces damaged bins that stick, wobble, or won’t seat correctly

What’s included
One vegetable/crisper drawer (sold individually).

Install notes

• Slide the old bin straight out; align and seat the new bin on the guides—no tools required
• Do not force; ensure the rail guides and center track are fully engaged
• Hand-wash only; avoid harsh cleaners that can stress and crack plastics

Usage tip
Keep heavier items on shelves above; overloading the bin can crack corners and stress the rails.

Restore a clean, reliable produce bin. This crisper drawer (vegetable tray) replaces cracked or missing bins so fruits and vegetables store properly and your fridge stays organized with smooth pull-out access.

What it does

• Provides dedicated produce storage in the fresh-food compartment
• Helps maintain proper humidity when used with the crisper cover
• Restores smooth slide-in/slide-out operation
• Helps prevent spills and items dropping behind the drawers
• Replaces damaged bins that stick, wobble, or won’t seat correctly

What’s included
One vegetable/crisper drawer bin (sold individually).

Install notes

• Unplug power before moving shelves or covers
• Pull the old bin straight out; align and seat the new bin fully on the guides
• Inspect rails and the crisper cover for cracks before reuse
• Hand-wash only; avoid harsh cleaners or high heat that can stress plastics

Replace a cracked or missing drawer cover to restore clean, organized storage in the fresh-food section. This cover sits above the drawer and helps keep items contained with smooth, reliable access.

What it does

• Forms the top cover over a pantry/crisper-style drawer
• Helps contain spills and prevents items from dropping behind the drawer
• Restores smooth slide-in/slide-out operation when the frame tabs are intact
• Replaces covers with broken corners, warped frames, or missing supports

What’s included
One drawer cover (tray cover).

Install notes

• Remove the drawer, lift out the damaged cover, and seat the new cover on its supports—do not force
• If your model uses a separate glass insert, handle carefully and transfer only if applicable
• Reinstall the drawer and verify smooth travel and full seating on the rails

This supporter cover is a TV rear trim piece that protects and conceals internal components while restoring the set's appearance. It provides a finished look and covers the TV's support area for safe handling and cosmetic repair. What it does

• Covers and protects the TV's rear support area and nearby components from dust and incidental contact
• Restores the TV's exterior finish after damage or missing trim pieces
• Helps maintain correct spacing for the support/stand attachment area
• Common symptom: cracked, warped, missing, or loose rear trim exposing internal parts

• One supporter cover

• Unplug the TV and place it face down on a soft, non-abrasive surface before starting
• Installation may require removing screws or disengaging plastic clips; keep hardware organized
• Handle carefully to avoid scratching the display or bending mounting tabs
• Refer to the TV's service manual for disassembly instructions and torque/spec guidance

This decor tray is the outer trim piece that restores the finished look around the appliance opening and protects underlying components from spills and wear. It matches the original appearance for a clean, factory-fit finish. What it does:

• Provides the visible trim/finish around the appliance opening so the exterior looks complete
• Covers and helps protect internal edges from spills, splashes, and everyday wear
• Restores worn, cracked or discolored trim to improve overall appearance
• Helps maintain a secure seal line by keeping the surrounding area intact

• High-level cosmetic part — basic snap-in or screw-fastening; refer to your model's service manual for exact removal/installation steps
• Disconnect power to the appliance if removing nearby panels to avoid electrical risk
• Handle part carefully to avoid scratching the finish during installation
• If hardware appears damaged, replace with OEM-specified fasteners

The Refrigerator Decor Assembly is an OEM replacement part for LG refrigerators. This cover is attached to the front of the deli drawer. It helps to maintain the cleanliness and freshness of the food items stored in the drawer. It also helps to protect the drawer from damage.

This part fixes the following symptoms:

• Difficulty opening and closing the deli drawer
• Damaged or missing cover
• Cracked, faded, or scratched cover

Causes of a bad decor assembly can include accidental damage during cleaning or use, degradation of materials over time, or improper installation causing misalignment.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Glass Shelf is an OEM replacement part for LG refrigerators. It provides sturdy, clear storage for items inside the refrigerator compartment. The glass shelf is designed to seamlessly integrate into the shelf system, dividing interior space for easy organization.

Causes of a bad glass shelf can include cracks or chips from heavy items, damage due to impact or mishandling, or general wear and tear over time.

Symptoms of a bad glass shelf include:

• Cracks or chips in the glass that compromise its structural integrity
• Leaks or moisture inside the fridge from a damaged shelf
• The shelf no longer fitting or functioning properly in the shelf system

This OEM LG part is also compatible with Sears/Kenmore.

This is a replacement door gasket assembly that restores the refrigerator door's airtight seal to help maintain proper temperatures and reduce energy loss. Use this OEM-style seal to replace torn, misshapen, or hardened door seals. What it does:

• Replaces the refrigerator door seal to help maintain a tight refrigeration seal
• Helps prevent warm air, moisture, and odors from entering the compartment
• Commonly used when the gasket is cracked, warped, or no longer rests flush
• Helps the appliance run more efficiently by reducing temperature fluctuations

• One door gasket assembly

• Disconnect power to the appliance before beginning any repair
• Gasket usually installs by tucking or fastening around the door flange; refer to your service manual for the exact procedure
• Inspect the door frame and mounting channel for damage or debris before installing the new gasket

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

This Door basket is the replacement door insert that holds and secures items in the appliance door, restoring safe storage and proper closure. Designed to replace a cracked, broken, or missing door basket. What it does

• Provides a molded storage pocket inside the appliance door so small items stay in place.
• Restores proper alignment and fit of the door interior when the original basket is damaged.
• Helps prevent items from shifting, rattling, or falling out during use.
• Commonly replaced when the basket is cracked, warped, or detached from the door.

• One door basket.

• Disconnect power and follow the appliance service manual before beginning repair.
• Removal/installation may require removing the door trim or inner liner—support the door to prevent damage.
• Wear gloves to protect against sharp edges and handle plastic clips carefully to avoid breakage.

The Door Basket is an OEM replacment part for LG French door refrigerators. It is a removable, flexible storage basket mounted inside the refrigerator door panel. The basket provides easy access to commonly used ingredients directly from the door.

Causes of a failing basket can include cracked or broken mounting clips over time. 

Symptoms of an inadequate basket include:

• Inability to securely hold contents inside the fridge door 
• Detachment from fasteners allowing it to dangle
• Holes or damage reducing usable storage space

This OEM LG replacement basket is also compatible with some Kenmore models.

This door stopper limits and cushions the appliance door's travel to prevent overextension and damage to hinges or surrounding surfaces. Replacing a worn or broken stopper restores smooth, controlled door movement and consistent closing alignment.

• Limits door opening angle and provides a positive stop to prevent overextension
• Helps protect hinges and adjacent panels from impact or scuffing
• Promotes smoother opening/closing and more consistent door alignment
• Symptoms of a failed stopper can include over-swing, scraping/rubbing, clicking noises, or a loose "stop" feel

• Disconnect power to the appliance before servicing
• Open the door to access the stopper; support the door if necessary
• Remove the fastener/retainer, note the old stopper's orientation, and install the new stopper using existing hardware
• Slowly open and close the door to verify the stop action and clearances after installation

The Door Closing Cam is an OEM part for LG refrigerators. This part ensures the refrigerator door closes smoothly and securely. It helps guide the door into the correct position and ensures a tight seal, which is essential for maintaining the internal temperature and efficiency of the appliance.

Causes of a bad door closing cam can include wear and tear over time, damage from repeated use, or accidental impacts that can misalign or break the cam. 

Symptoms of a bad Door Closing Cam include:

• The door not closing properly or securely
• Difficulty in opening or closing the door
• Unusual noises when operating the door
• Misalignment of the door

This OEM LG part is also compatible with some Kenmore models.

This snap-in hole plug button covers unused panel openings to restore a finished look and help keep out dust and moisture. A simple cosmetic trim piece that snaps into place and blends with the control panel. What it does:

• Covers exposed holes in control panels and consoles to improve appearance
• Helps block dust, lint and small debris from entering appliance openings
• Prevents accidental contact with internal components through unused holes
• Useful when replacing damaged buttons or finishing a repair

• One snap-in hole plug button

• Disconnect power to the appliance before working on the control panel
• Press the plug into the hole until it snaps flush; use a flat tool gently if needed
• Inspect fit and panel edge for damage; replace if cracked or loose to ensure a secure fit
• If panel removal is required, follow manufacturer instructions to avoid breaking clips

This hinge cover is a cosmetic and protective trim piece that snaps over the door hinge to hide hardware and protect the hinge area from dust and damage. It restores the finished look and helps keep the hinge area cleaner. What it does:

• Covers and protects the door hinge hardware from dust, spills, and everyday wear
• Conceals exposed screws and components for a finished appearance
• Reduces chance of items catching on the hinge area and causing damage
• Helps stop light rattles or vibration noise caused by loose or damaged trim

• Install by snapping the cover over the hinge; may require lightly prying off the old cover first
• Inspect hinge screws and hinge pin; tighten if loose before installing the cover
• Use basic hand tools; disconnect power only if you will be working near electrical components
• If cover is cracked or broken, replace to avoid interference with door operation

This hinge cover protects and conceals the washer's lid hinge assembly for a clean look and safer operation. It helps keep debris out of the hinge and restores the cabinet appearance after damage. What it does:

• Covers the lid hinge to protect internal hinge components from dirt and damage
• Conceals exposed hardware for improved appearance and user safety
• Restores smooth lid operation when original cover is cracked, broken, or missing
• Reduces rattling and contact between the lid and hinge area

• Disconnect power to the appliance before starting any repair
• Remove any screws or clips securing the old cover and gently snap or slide the replacement into place
• Use basic hand tools; keep small hardware organized for reassembly
• If hinge hardware is damaged or binding, inspect and replace those parts as needed for proper operation

Note: Top LEFT Hinge

Note: Top RIGHT hinge

This hinge cap protects and covers the appliance hinge pivot, keeping the hinge area clean and helping the door operate smoothly. It restores the finished look and prevents debris from entering hinge components. What it does:

• Covers the hinge pivot to reduce dirt buildup and wear
• Helps keep the door aligned by protecting hinge moving parts
• Fits where a small plastic hinge cover is required

• Power off or unplug the appliance before servicing if working near electrical components
• Typically snaps or slides into place; remove the door or hinge trim only if instructed by the service manual
• Use basic hand tools as needed and avoid forcing the cap to prevent breakage
• If hinge components are damaged or the door misaligns, inspect the hinge assembly and replace any worn parts

The Hinge Bushing is an OEM part for LG refrigerators. It serves as a crucial component in the door hinge mechanism, ensuring smooth and stable operation when opening and closing the refrigerator door.

You should replace this hinge bushing if it becomes worn out or damaged. Common causes of a bad hinge bushing include constant use leading to wear and tear, misalignment of the door, or physical damage due to impact.

Symptoms of a bad hinge bushing include:

• Difficulty in opening or closing the door
• The door sagging or not aligning properly
• Unusual noises like squeaking or grinding when the door is moved

This OEM LG part is also compatible with Sears/Kenmore.

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

NOTE: This part also requires software update kit CJT30000002. DO NOT INSTALL WITHOUT UPDATING SOFTWARE. Call for more information.

The Compressor Overload Protector Assembly is an OEM part for LG refrigerators. The compressor overload protector steps in if the compressor motor draws excessive current. It then interrupts the power to prevent overheating. The wire harness boosts the compressor to kick-start it, disengaging as soon as the motor reaches the desired speed.

Over time, the compressor overload protector can wear out or become damaged due to electrical issues, power surges, or constant exposure to high temperatures. A faulty protector can compromise the safety and efficiency of the refrigerator’s cooling system.

Symptoms of a bad compressor overload protector assembly include:

• The refrigerator not cooling properly
• The compressor frequently cycling on and off
• Clicking noises coming from the compressor area
• The refrigerator not turning on at all

This OEM LG part is also compatible with Sears/Kenmore models.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This holder secures the dryer-related assembly in place to reduce movement and wear, helping maintain proper alignment and quieter operation. It's a simple replacement that restores part stability in the appliance. What it does:

• Secures a dryer assembly or component to the appliance frame to prevent shifting
• Helps reduce vibration and rubbing noises caused by a loose part
• Maintains correct alignment so related parts operate smoothly
• Used when the existing holder is cracked, broken, or missing

• Disconnect power before replacing any dryer components to avoid shock or injury
• Access location and removal steps vary by model; follow the appliance's service manual or exploded view
• Keep fasteners and adjacent parts organized for reassembly; replace any damaged clips or screws

This motor bracket is the OEM-style mounting bracket that secures the appliance motor to the cabinet, keeping the motor aligned and reducing vibration for reliable operation. It helps restore proper motor support and stable running. What it does:

• Provides a secure mounting point to hold the motor in correct position
• Maintains motor alignment to prevent belt slip and uneven wear
• Reduces vibration and noise caused by a loose or damaged motor mount
• Can resolve symptoms such as unusual motor noise, excessive vibration, or motor movement during operation

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance service manual for access steps
• Inspect surrounding components (mounting fasteners, motor and belts) and replace any damaged parts

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

The Evaporator Fan Motor is an OEM part for LG refrigerators. It powers the evaporator fan located inside the refrigerator's cooling system. The evaporator fan circulates chilled air through ducts and into food storage compartments, helping maintain an even temperature.

Causes of a bad evaporator fan motor include failure due to bearing wear, component fatigue from continuous operation, damage from debris accumulation over time inhibiting rotation, or failure of electronic components controlling motor function.

Symptoms of a faulty evaporator fan motor include:

• Temperature fluctuations in refrigerator and freezer sections
• Intermittent cooling or inability to cool fully
• Abnormal fan noise or abnormal vibration
• Frost or moisture buildup within refrigerator ducts

This LG part is also compatible with some Kenmore models.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

This LED light assembly illuminates the refrigerator interior when the door opens, delivering bright, efficient lighting so you can easily see items. Replace a failed module to restore proper visibility inside your fridge.

• Provides interior illumination for the fresh food or freezer compartment
• Turns on and off with the door switch
• Helps you quickly find items and check food condition
• Common symptoms: no light when doors open, flickering/strobing, dim or intermittent lighting

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, release retaining tabs, and unplug the wire harness to remove the old module
• Connect the new assembly, align tabs, and snap/secure it into place; reinstall the cover
• Restore power and verify operation; the door switch activates the light

The Capacitor is an OEM part for LG refrigerators. It plays a vital role in the electrical system, providing the necessary power boost to start the compressor and maintain its operation. This component ensures that the refrigerator runs efficiently by stabilizing voltage and improving overall performance.

Common causes of a bad capacitor include electrical surges, wear and tear over time, or exposure to excessive heat.

Symptoms of a bad capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual noises coming from the refrigerator
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes the electrical cord and strain relief that links the refrigerator to an external power source.  

This power cord assembly safely delivers electricity from the wall outlet to the internal compressor and fan modules. It facilitates proper cooling functions through this transmission of alternating current.

Symptoms of a bad power cord can include:

• Abnormal sounds such as humming or buzzing from within 
• Tripped circuit breakers interfering with operations
• Indicators of cord damage like frays or exposed wiring
• Inconsistencies in interior temperature maintenance

Causes may involve normal wear over extended use, physical stress, or accidental damage to the cord insulation.  

Replacing the power cord assembly with this genuine LG OEM part restores a reliable electrical pathway. It ensures a continued power supply to keep foods fresh and frozen.

The Compressor Overload Protector Assembly is an OEM part for LG refrigerators. The compressor overload protector steps in if the compressor motor draws excessive current. It then interrupts the power to prevent overheating. The wire harness boosts the compressor to kick-start it, disengaging as soon as the motor reaches the desired speed.

Over time, the compressor overload protector can wear out or become damaged due to electrical issues, power surges, or constant exposure to high temperatures. A faulty protector can compromise the safety and efficiency of the refrigerator’s cooling system.

Symptoms of a bad compressor overload protector assembly include:

• The refrigerator not cooling properly
• The compressor frequently cycling on and off
• Clicking noises coming from the compressor area
• The refrigerator not turning on at all

This OEM LG part is also compatible with Sears/Kenmore models.

The MOTOR, DC is an OEM part for LG refrigerators. It is a direct current electric motor responsible for operating components related to cooling and airflow, such as the condenser fan and cooling fan. Efficient airflow circulation is critical for pulling heat away from refrigerated compartments and maintaining even temperatures throughout the fridge.

Causes of a bad motor can include excess dust buildup over time inhibiting proper fan rotation, worn motor brushes, or damaged motor windings affecting current flow. 

Symptoms of a bad direct current motor include:

• Abnormally warm refrigerator temperatures 
• Louder than usual operating sounds
• Lack of air coming from ventilation areas  
• Visible buildup of frost or condensation inside the fridge

Replace yours today with this genuine OEM LG part to restore optimal cooling performance. This OEM LG part is also compatible with Sears/Kenmore.

The Gasket, Foam is an OEM part for LG refrigerators. This foam gasket creates an essential seal around the refrigerator door, helping to maintain cool interior temperatures and block warm air from entering. It also assists in preventing moisture exchange, keeping contents dry. 

Symptoms of a damaged gasket include:

• Warm or unpleasant air feeling around the edges of the door 
• Higher energy costs from poor insulation
• Extra frost or moisture buildup inside
• Visible air gaps when the door is closed

Causes may be general wear and breakdown over time due to repeated opening and closing of the door. Replace this LG OEM foam gasket to restore an efficient seal and optimal refrigerator performance. This gasket is compatible with models produced by Kenmore, Sears, Samsung, Electrolux, and GE as well.

The Inlet Water Valve Assembly is an OEM part for LG refrigerators, designed to manage the flow of water into the refrigerator's ice maker and water dispenser. This part ensures that your refrigerator provides clean, fresh water and ice on demand by controlling the water pressure and flow through the system. The valve assembly is key to maintaining the refrigerator's functionality and the freshness of the water and ice it dispenses.

Causes of a bad Valve Assembly, Water can include mineral build-up from hard water, which can block the valve and prevent it from opening or closing properly. 

Symptoms of a bad Valve Assembly include:

• No water dispensed
• Leaking water from the refrigerator
• Ice maker not producing ice
• Strange noises coming from the refrigerator when the dispenser is used

This OEM LG part is also compatible with some Kenmore models.

The Temperature Sensor is an OEM part for LG refrigerators. It monitors the internal temperature and sends this information to the control board, ensuring that the refrigerator maintains the correct temperature for optimal food preservation.

Over time, temperature sensors can fail due to electrical issues, exposure to moisture, or wear and tear from continuous use. 

Symptoms of a bad temperature sensor include:

• Inaccurate temperature readings
• The refrigerator or freezer being too warm or too cold
• The refrigerator running constantly or not running at all
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances.