Parts for Kenmore 796.51993610 (79651993610, 796 51993610): Other Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This Front Cover is the outer housing panel that restores the exterior of the appliance and protects internal components from dust and damage while improving appearance. It's the visible panel that helps keep the unit sealed and looking finished. What it does:

• Replaces a cracked, dented, or faded outer panel to restore cabinet appearance
• Protects internal parts and wiring from debris and accidental contact
• Helps maintain proper airflow around controls and vents
• Reduces vibration noise caused by loose or damaged panels

• One Front Cover panel

• Disconnect power to the appliance before beginning any work
• Remove any trim, handles, or fasteners that secure the front cover; save hardware for reuse unless new hardware is supplied
• Handle the panel carefully to avoid scratching the finish; alignment shims or clips may be required for proper fit

This accessory assembly is a factory replacement component that restores the original mounting/connection function in compatible LG appliances, helping eliminate loose fittings and restore secure operation. What it does

• Replaces a worn or damaged accessory assembly that secures or connects appliance components.
• Restores proper alignment and engagement of the affected assembly to reduce rattling or movement.
• Can help address symptoms such as loose parts, intermittent connection issues, or unusual noises originating near the assembly.
• Matches OEM fit and form to maintain original performance when installed correctly.

• Disconnect power (unplug or shut off breaker) before beginning any repair.
• Basic hand tools are typically required; follow the appliance service manual for removal and installation steps.
• Inspect surrounding components for wear or damage while replacing this assembly.

This accessory assembly is a factory-style replacement that restores missing or damaged accessory components so the appliance operates as intended. It provides the correct mounting and connection points for attached parts. What it does:

• Replaces a damaged or missing accessory assembly to restore proper accessory function
• Provides the OEM mounting points, connectors, and hardware interface for attached components
• Addresses symptoms such as loose or missing accessory parts, intermittent accessory connections, or improper fit
• Helps ensure accessories attach securely and align correctly with the appliance housing

• Disconnect power and water before starting service
• Follow the OEM instructions for removal and installation
• Basic hand tools are typically required; avoid forcing clips or connectors

Replacement dispenser assembly that restores the refrigerator door's water/ice dispensing function and replaces a cracked or non-working dispenser chute or bezel. Helps stop leaks and returns reliable dispensing action. What it does:

• Routes water and/or ice from the dispenser to the cup and houses the dispenser actuator and mounting points.
• Replaces cracked, broken or worn dispenser chutes and bezels that cause leaks or catching.
• Restores dispenser lever/actuator responsiveness when the door switch or paddle is damaged.
• Can stop visible leaking from the dispenser area and improve user access to dispensed water or ice.

• Disconnect power and water supply before starting work to avoid shock or leaks.
• Remove refrigerator door trim or liner to access dispenser mounting screws and connectors.
• Handle sharp sheet-metal edges and beverage lines carefully; inspect and replace any damaged gaskets or tubing.

This leg support secures the adjustable leveling foot to the appliance's base. Replacing a damaged or stripped support restores a solid mounting point so you can properly level the unit and reduce rocking and vibration. What it does

• Provides the mounting point for the leveling leg; anchors to the base/frame
• Helps keep the appliance level and stable during operation
• Replace if cracked, bent, or the threads are stripped
• Common symptoms: rocking or unstable unit, excessive vibration/rattling, doors out of alignment, leveling foot won't hold adjustment

• 1 leg support

• Disconnect power; shut off water or gas supply if applicable
• With a helper, carefully tip and support the unit to access the base safely
• Remove fasteners, transfer or thread the existing leveling leg into the new support, and reinstall
• Set the appliance down and level it on all corners; verify stability

This Supporter, Leg is the base bracket that holds the leveling foot at the cabinet. It stabilizes the unit and enables precise leveling to help prevent rocking, vibration, and door or drawer misalignment during everyday use.

• Supports and locates the leveling leg/foot at the base of the cabinet
• Provides a secure mounting point for height adjustment and stability
• Helps keep the cabinet square and reduces wobble and vibration
• Common symptoms of a failed support include rocking, difficulty leveling, or a visibly cracked/bent bracket

• Disconnect power and protect flooring before moving or tilting the appliance
• Access the base area (remove the toe grille/kick panel if equipped)
• Unload the leg, remove mounting fasteners, and transfer the leveling foot to the new support if needed
• Reassemble and verify the unit is level front-to-back and side-to-side

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

This top cover is a direct-replacement cabinet panel that restores the appliance's exterior finish and protects internal components from dust and damage. It helps maintain a safe, finished appearance and prevents debris from entering the chassis. What it does:

• Covers and protects internal components located at the appliance top
• Restores a smooth, finished exterior surface after damage or corrosion
• Eliminates gaps that can collect dust, lint, or liquids
• Helps prevent sharp edges and reduces risk of contact with internal parts

• One replacement top cover

• Disconnect power (and water, if applicable) before beginning work
• Remove trim or access panels as needed to reach mounting screws
• Support the cabinet while removing/installing the cover to avoid dropping or bending

This Top Cover is the outer cabinet panel that fits over the appliance's upper section to protect internal components and restore a finished appearance. It keeps controls and wiring covered while improving the unit's look. What it does:

• Covers and protects control components and wiring from dirt, spills, and accidental contact
• Restores a flush, finished appearance when the original top is dented, cracked, or missing
• Helps reduce airflow into the cabinet area to prevent debris buildup
• Provides a secure mounting surface for control assemblies and trim pieces

• Disconnect power (unplug or shut off breaker) before beginning any service
• Typical installation requires removing a few fasteners and lifting the old cover off; keep track of screws and clips
• Handle edges carefully to avoid cuts and protect painted surfaces from scratches
• Refer to your model's service manual or parts diagram for fastener locations and any bracket reassembly steps

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

This leveling leg assembly supports and stabilizes the appliance cabinet. It threads into the base to help level the unit on uneven floors, reducing vibration and movement for quieter, steadier operation.

• Provides height adjustment to level the appliance
• Helps reduce excessive vibration, walking, and rattling
• Supports proper door alignment and smooth operation
• Common fix when the unit rocks or is difficult to level

• Unplug the appliance and shut off water/gas before service
• Carefully tip or access the base to reach the leg location
• Thread the new leg by hand; adjust height with a wrench as needed
• The cabinet is level front-to-back and side-to-side

This inlet hose delivers water from the household supply to the appliance for normal fill cycles. It restores proper water flow when the original inlet hose is damaged, cracked, or leaking. What it does:

• Channels incoming water from the household supply to the appliance's fill valve
• Replaces a worn, cracked, or leaking inlet hose to stop external leaks
• Helps restore normal fill and wash cycles affected by restricted or damaged hoses
• Fits as a direct replacement for the corresponding OEM inlet connection

• One inlet hose

• Disconnect power and shut off the water supply before starting any work
• Inspect fittings and replace any damaged clamps or seals to ensure a watertight connection
• Hand-tighten connections, then snug with a wrench—avoid over-tightening which can damage fittings
• Test for leaks by running a short fill cycle and checking all connections

This tub cover assembly replaces the inner cover that surrounds the washer tub, restoring proper sealing and alignment so clothes move freely and the wash action stays consistent. What it does:

• Covers and protects the tub interior, helping keep clothes clear of internal components
• Helps maintain proper drum alignment and reduces rubbing or catching of items
• Restores the tub enclosure when the existing cover is cracked, warped, or broken
• Can reduce abnormal noise caused by a damaged cover contacting the drum

• Disconnect power and water supply before starting any repair
• Installation generally requires partial disassembly of the washer cabinet and removal of the outer tub or drum assembly
• Handle edges carefully—parts and cabinet openings can be sharp
• Use OEM fasteners and follow manufacturer instructions for proper reassembly

This replacement switch assembly restores a failed control switch so the appliance's push-button or rocker inputs respond reliably. Fits where the original electrical switch no longer completes the control circuit. What it does

• Completes the electrical circuit when a control button or rocker is pressed
• Restores responsive control input for the affected function
• Can stop intermittent or no-response behavior from worn or broken switches
• Helps resolve control-related failures caused by damaged switch contacts

• Disconnect power (unplug or shut off breaker) before starting any work
• Note and/or photograph wiring and connector locations before disconnecting
• Reconnect wiring securely; ensure harnesses are routed to avoid pinching
• Test the control function after restoring power; do not operate if wiring appears damaged

The Common Bolt is an OEM part for LG washing machines. It is a necessary mounting hardware component used to securely fasten and assemble various internal parts and components. Common bolts play a crucial role in ensuring the washer maintains solid construction and can withstand the shaking and vibrations of each wash cycle.

Causes of a bad common bolt can include stripped threads, rust, or damage over time due to repeated use or exposure to detergents and chemicals.

Symptoms of a bad common bolt include:

• Loose or detached internal parts
• Excessive noise or vibration
• Leaks around seal areas

This OEM LG part is also compatible with some Kenmore models.

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

This drain hose connector links the dishwasher's drain hose to its mating port for a secure, leak-resistant fit, helping wastewater exit properly and reducing leaks at the hose connection point. What it does:

• Joins the drain hose to the appliance's drain system and maintains a tight seal
• Helps ensure proper drainage during the pump-out portion of the cycle
• Provides a secure connection to resist hose slippage
• Common symptoms include leaks near the hose fitting, a loose or cracked connector, the hose popping off, or slow/poor draining due to a loose connection

• Disconnect power at the breaker and shut off the water supply before servicing
• Pull the unit forward to access the drain path and place a towel to catch residual water
• Loosen the hose clamp(s), remove the old connector, fully seat the hose on the new connector, and re-secure the clamp(s)
• Run a short cycle and check all connections for leaks

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This genuine replacement door handle restores a secure grip and smooth opening for compatible LG appliances. Durable and shaped to match the original, it replaces a cracked, loose, or missing handle so the door operates safely and conveniently. What it does:

• Provides a solid grip for opening and closing the appliance door
• Replaces handles that are cracked, broken, loose, or missing
• Restores original fit and alignment so the door seals and latches properly
• Helps prevent further damage from forcing or makeshift grips

• One door handle

• Disconnect power and empty the door area before starting; follow all safety precautions
• Common installation requires removing a few screws or trim pieces; keep fasteners organized
• Handle mounts to the door using existing screw locations—do not overtighten

The Valve Assembly, Inlet is an OEM part for LG washing machines. This valve assembly is responsible for controlling the flow of water entering the washer. It is designed with precision-engineered components to regulate water levels and pressure accurately during each cycle.  

Causes of a bad valve assembly can include a buildup of minerals or debris inside the assembly over time, wear from heavy or extended use, or damage to internal valve components.

Symptoms of a failing inlet valve assembly include:

• Incorrect or uneven water fill levels between cycles
• Abnormal noises or lack of sound when water is supposed to enter 
• Fluctuations in water pressure or temperature
• Inability to start or complete cycles due to water flow issues

Replacing the valve assembly with this new OEM part restores optimal water control. Proper water fill is essential for thorough cleaning and rinsing performance.

This LG replacement part is also compatible with Sears/Kenmore models.

This is a drain hose made of durable plastic that is used in a variety of washing machines. The drain hose is the component responsible for removing any wastewater from the appliance. It is located on the back of the washing machine near the water hookups. The drain hose takes dirty water out, while the other hoses bring fresh water in. If the drain hose is damaged, it can prevent the washer from filling, cause water leaks, or result in loud noises.If the drain pump is cracked or broken it should be replaced. Disconnect the appliance from power and water before starting. Remove the clamps that hold the drain hose to the back of the washer. Remove the drain hose. Next, take the new drain hose and slide the clamp onto it. Install the hose into the machine and reassemble it before using the appliance.This drain hose is created to be compatible with LG washing machines. It is sold as an individual part. This is a genuine OEM replacement component that is directly sourced from the manufacturer.

The Valve Assembly, Inlet is an OEM part for LG washing machines. This valve assembly is responsible for controlling the flow of water entering the washer. It is designed with precision-engineered components to regulate water levels and pressure accurately during each cycle.  

Causes of a bad valve assembly can include a buildup of minerals or debris inside the assembly over time, wear from heavy or extended use, or damage to internal valve components.

Symptoms of a failing inlet valve assembly include:

• Incorrect or uneven water fill levels between cycles
• Abnormal noises or lack of sound when water is supposed to enter 
• Fluctuations in water pressure or temperature
• Inability to start or complete cycles due to water flow issues

Replacing the valve assembly with this new OEM part restores optimal water control. Proper water fill is essential for thorough cleaning and rinsing performance.

This LG replacement part is also compatible with Sears/Kenmore models.

This is a replacement power push-button switch used to turn the appliance on and off. It restores a tactile, visible control so you can reliably power the unit without replacing the whole control panel. What it does:

• Provides a user-facing push-button to send the on/off signal to the control board
• Replaces worn, broken, or non-responsive power button that prevents powering the appliance
• Restores proper button travel and tactile feedback for normal operation
• Fits into the front control panel and interfaces with the original switch mechanism

• Disconnect power before starting any repair to avoid electrical shock
• Access may require removing the control panel; retain screws and fasteners for reassembly
• Seat the button into the panel and engage the underlying switch mechanism
• If the appliance still will not power on after replacement, test the console and wiring before replacing additional parts

This part is a hinge. This is a genuine OEM part made by LG and has been sourced directly from the manufacturer. This part is intended to replace a broken or defective hinge on multiple different models of LG washers and dryers. This part is made for use with LG appliances and may not correctly fit appliances manufactured by other brands. This hinge is for attaching the lid of the washer or dryer to the appliance, allowing it to open and close smoothly. If the lid will not open properly, the hinge may need to be replaced. Please follow appropriate safety precautions when attempting to replace any appliance parts. Ensure the washer or dryer is fully disconnected from its power source before attempting this repair. For more accurate information on how and where to install this replacement hinge, the manufacturer owner's manual and diagrams should be referenced.As an authentic replacement part, this hinge is suitable for use on several different models of washers and dryers manufactured by LG. Please note that this is a genuine part made of high-quality, durable plastic and is sold individually.

This drain pump assembly replaces a failed washer drain pump to restore normal water removal. It helps clear standing water so cycles can finish and reduces leaks or overheating risks from trapped water. What it does:

• Pumps water from the tub to the household drain during drain/spin cycles.
• Common failure signs: washer won't drain, water left in tub after cycle, or cycle stalls.
• A leaking pump can allow water to escape under the machine or trigger error codes.

• Disconnect power and shut off water before starting any repair.
• Drain remaining water from the tub and disconnect hoses carefully to avoid spills.
• Match and reconnect electrical connectors exactly; secure hose clamps and check for leaks.
• After installation, run a short drain/spin cycle and inspect for proper operation and leaks.

This thermistor assembly monitors water temperature inside the washer tub and relays a precise signal to the control board. Replacing a failed sensor restores accurate temperature sensing and helps prevent cycle errors and performance issues. What it does:

• Measures wash water temperature and sends the signal to the electronic control
• Enables the control to adjust cycle operation based on temperature feedback
• Common failure signs: tE/TE error codes on some models, incorrect temperatures, long cycles, or cycles that won't advance
• Intermittent faults may cause sporadic errors or inconsistent performance

• 1 thermistor assembly

• Disconnect power and shut off water before servicing
• Access location varies by model; the sensor is typically mounted in the outer tub or heater housing
• Unplug the harness, pull the old sensor straight out; seat the new sensor fully and reconnect the harness
• Route wiring away from moving parts; restore power and run a test cycle, checking for proper operation and any leaks around the sensor port

This power cord assembly supplies AC power to the appliance and restores safe operation after a damaged or faulty cord. It replaces the worn or frayed factory cord so the appliance can power on reliably. What it does

• Provides the main AC connection between the appliance and household power
• Replaces cords with visible damage, exposed wiring, burnt connectors, or intermittent power
• Helps stop arcing, sparking, or overheating caused by a failing cord
• Fits into the appliance's cord terminal block for a direct, plug-in power connection

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before starting any work
• Tighten all terminal screws securely and route the cord away from sharp edges and moving parts

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

This bellows is the flexible rubber door boot seal that creates a watertight barrier between the washer door and tub, helping prevent leaks and keeping laundry contained during cycles. What it does:

• Seals the front-load door opening to stop water from escaping during wash and spin cycles
• Helps prevent leaks that can cause water on the floor or under the machine
• Keeps lint, soil and moisture inside the drum, reducing musty smells
• Restores a damaged, torn or hardened boot to proper sealing performance

• One bellows

• Disconnect power and water supply before starting any repair
• Drain remaining water from the tub to avoid spills when removing the old boot
• Removing the door trim and spring clamp may be required; keep track of all fasteners

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.