Parts for Lg LBC24360ST/03: Other Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

The Drain Tube Assembly is an OEM part for LG refrigerators. This drain tube assembly is responsible for directing condensation and melt water that accumulates in the refrigerator away to the evaporator pan.

Causes can include cracks developing from limescale or mineral accumulation, flexing fatigue from repeatedly catching drips, or damage from improper cleaning methods.

Symptoms of a bad drain tube assembly include:

• Puddles or leaks developing underneath the refrigerator
• Poor air flow from vents and higher temperatures
• Ice or moisture buildup in refrigerator walls and seals
• Water stains or corrosion appearing inside the unit

This OEM LG part is also compatible with some Kenmore models.

This leveling leg assembly stabilizes and levels your refrigerator so it sits solidly on the floor and the doors align correctly. Replacing a worn or stripped leg helps reduce rocking and vibration and restores smooth leveling adjustment.

• Provides height adjustment to level the cabinet on uneven floors
• Supports the unit to prevent rocking or wobbling
• Helps doors close and seal properly when the cabinet is level
• Symptoms may include persistent wobble, vibration/rattling, or a stripped/bent foot or screw

• Unplug the refrigerator and use a helper to prevent tipping injuries.
• Protect flooring; remove the kickplate/grille for access if present.
• Thread out the worn leg; hand-thread the new assembly and adjust height—do not over-extend.
• Level side-to-side and front-to-back per your owner's manual, then reattach any panels.

The Guide Assembly Rail (RH) is an OEM part for LG refrigerators. This Right-hand rail is responsible for guiding the movement of drawers or shelves within the refrigerator, ensuring smooth and secure sliding. It helps maintain proper alignment and stability of the drawers, making it easier to access stored food items.

Causes of a bad guide rail can include wear and tear over time, damage due to heavy loads or excessive force when opening and closing the drawers, or misalignment from improper installation. A faulty rail can affect the performance of the drawer, leading to difficulties in accessing the refrigerator’s contents.

Symptoms of a bad guide rail include:

• Drawers not sliding in and out smoothly
• Misaligned or wobbly drawers
• Difficulty opening or closing drawers completely

This OEM LG part is also compatible with Sears/Kenmore.

The Guide Assembly, Rail (LH) is an OEM part for LG refrigerators. This component is located within the fridge compartment and is responsible for guiding and supporting the bottom drawer, ensuring it opens and closes smoothly along the right-hand side. The guide rail assembly helps the drawer maintain proper alignment and prevents it from tilting or binding during operation.

Causes of a bad guide rail assembly can include wear and tear from regular use, damage from overloading the drawer, or accidental impacts that may bend or misalign the rail.

Symptoms of a bad Guide Assembly, Rail (LH) include:

• Difficulty opening or closing the drawer
• The drawer not aligning properly
• Unusual noises when opening or closing the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

This is the ice bucket that stores ice dispensed by your refrigerator's ice maker. A cracked, warped, or stuck bin can jam the auger or spill ice, leading to poor dispensing and messy freezers.

• Holds and dispenses harvested ice from the ice maker to the door chute or bin access
• Common failure signs: cracked bucket, ice not dispensing, auger not turning, ice clumping or spilling
• Restores smooth ice dispensing and proper storage in the freezer
• Built to fit the original mounting and drive interface for an easy swap

• Unplug the refrigerator and wear cut-resistant gloves
• Remove the old bin carefully; thaw any ice buildup before transferring
• Inspect the auger drive coupling for wear before installing the new bucket
• Seat the bucket fully so the drive engages; test dispense with a small amount of ice

Restore a sturdy, clean storage surface inside your refrigerator with this replacement drawer tray. It replaces a cracked or missing tray so food stays organized and the drawer fits and functions as intended. What it does:

• Provides the flat base/support for a refrigerator storage drawer
• Helps keep food organized and prevents items from tipping or falling
• Maintains proper fit and alignment of the drawer within the compartment
• Common symptoms: cracks, broken tabs, warping, drawer not sitting level or sliding smoothly

• 1 drawer tray

• Empty and remove the drawer before replacing the tray
• Align and seat the new tray fully in the guides; ensure it is level before reloading
• Transfer any reusable hardware from the old tray if applicable
• Handle plastic carefully to avoid stress cracks; do not force into place

This roller is the small wheel that lets a sliding component move smoothly along its track. Replacing a worn or cracked roller restores easy, quiet operation and helps prevent binding, noise, and uneven travel.

• Supports and guides a moving bin, drawer, or rack on its track
• Reduces friction for smooth, even motion
• Common symptoms: sticking or hard-to-open movement, grinding/clicking noises, wobbling/misalignment, or a cracked/missing wheel
• Helps protect tracks and brackets from excess wear

• Disconnect power before servicing; wear gloves to protect hands
• Remove the sliding component to access the roller
• Release the clip/fastener, install the new roller, and transfer/reuse original hardware if applicable
• Test movement to ensure the roller is fully seated and tracking correctly; replace in pairs when applicable for even travel

Roller assembly approx. 1".

A replacement glide rail assembly that supports and guides a refrigerator/freezer drawer for smooth opening and closing. Restores proper drawer tracking and helps prevent sticking or misalignment. What it does:

• Provides the rail and mounting components that the drawer slides on for stable operation
• Restores smooth drawer movement and alignment when original rail is bent or worn
• Helps reduce drawer sticking, scraping, or uneven travel
• Intended for use where the OEM glide/rail assembly is specified

• One glide rail assembly

• Follow the appliance manufacturer's service manual for removal and installation steps
• Disconnect power and empty the drawer before working to prevent injury or damage
• Inspect mounting hardware and drawer slides; replace any damaged fasteners
• Use basic hand tools;

This guide assembly rail replaces a worn or damaged drawer slide to restore smooth, stable drawer movement and proper alignment. It helps reduce sticking, misalignment, and rattling for a secure fit and quiet operation. What it does:

• Guides and supports the drawer or compartment during open/close cycles
• Restores smooth sliding action and consistent alignment
• Reduces noise caused by worn or bent rails or guides
• Helps prevent drawers from catching or binding

• Disconnect power and empty the drawer before beginning service
• Removal of the drawer and access panel may be required; keep fasteners for reassembly
• Align the rail before tightening fasteners; use basic hand tools

This rail guide assembly replaces a worn or damaged drawer/rack guide to restore smooth, stable movement and help prevent the rack or drawer from binding or coming off track. Fits original mounting points for a direct replacement. What it does:

• Guides and supports the drawer or rack so it slides in and out smoothly
• Helps keep the rack/drawer aligned to prevent derailment or sticking
• Replaces broken or worn plastic or metal guide components that cause noisy or rough movement
• Restores intended fit and function of the sliding mechanism

• Disconnect power and remove contents from the drawer/rack before starting any work
• Basic hand tools may be required; follow OEM instructions for orientation and attachment
• Inspect mating slides and fasteners; replace any damaged clips or screws for secure fit

This Tray Assembly is the replacement vegetable-drawer pan that holds produce and helps contain spills inside the fridge. Restores a secure storage surface so fruits and vegetables sit level and are easier to organize. What it does:

• Replaces a cracked, warped or broken vegetable drawer pan that no longer supports produce
• Contains leaks and small spills to help keep the refrigerator interior cleaner
• Provides a stable base for crisper/vegetable drawers to slide and sit properly
• Helps restore proper drawer alignment and prevents items from falling through gaps

• Remove fresh food and open/slide out the affected drawer; lift to disengage and remove the old pan
• Align new tray with drawer rails and slide in until it seats; verify smooth operation before loading
• Handle glass or brittle plastics with care to avoid chips or cracks during installation

This genuine replacement knob shutter restores the control panel's knob opening and protects internal switches from debris while allowing knobs to engage properly. It helps maintain smooth knob operation and reduces dirt buildup behind the control surface. What it does:

• Covers the knob opening and guides the control knob into place for reliable engagement
• Protects internal switches and electronics from dust, crumbs, and spills
• Helps prevent accidental knob movement when not in use
• Restores proper fit and appearance of the control panel area

• One knob shutter

• Power off and unplug the appliance before beginning any work to avoid electrical shock
• Small fasteners or clips may need to be removed; use appropriate hand tools and keep track of hardware

This replacement cover assembly restores a clean, finished look and protects underlying components from dust, moisture, and impacts. Replace a cracked, discolored, or missing cover to maintain proper protection and appearance. What it does

• Provides a protective and decorative panel over internal components
• Helps keep out dust and moisture while maintaining a finished exterior
• Replaces covers with broken tabs, cracks, or warping
• Addresses issues like panels that won't stay attached, rattling, or exposed mechanisms

• One cover assembly

• Unplug the appliance before servicing; wear cut-resistant gloves
• Use non-marring pry tools to release tabs and avoid scratching surrounding surfaces
• Retain and transfer any screws, clips, or seals from the original part
• Test fit before fully seating and tightening to avoid stressing plastic tabs

This supporter cover is a replacement rear support/trim piece that helps secure and protect the back of the television cabinet, restoring proper fit and finish. It's a direct-fit OEM-design part for models that list PN MJH62434203. What it does:

• Provides structural support to the TV rear cabinet and helps keep internal components properly positioned.
• Covers and protects rear openings from dust and incidental contact.
• Restores original appearance where a damaged or missing cover left gaps or exposed hardware.
• Helps prevent rattling or vibration caused by loose or broken rear trim.

• One supporter cover (PN MJH62434203) as shown.

• Follow manufacturer disassembly instructions for access; keep power disconnected and TV laid on a soft, flat surface to avoid screen damage.
• Use proper fasteners from the original unit; only install if the mounting points are intact.
• If internal components were shifted or damaged, inspect for additional repair needs before reassembly.

This tray cover creates a level, protective surface over a storage tray or bin inside the appliance. Replacing a cracked or missing cover restores proper support, helps contain spills, and keeps drawers or trays operating smoothly.

• Provides a flat support surface above the tray/bin to hold items
• Helps contain small spills for easier cleanup
• Maintains correct spacing so drawers/trays slide and close properly
• Common failure symptoms: cracked or broken plastic, missing tabs, sagging shelf, drawer not sliding or closing right

• Disconnect power and clear the area around the affected tray
• Remove the tray/bin, then lift out the damaged cover; note orientation and support tabs
• If applicable, transfer any removable components from the old cover
• Seat the new cover fully into the supports and reinstall the tray/bin

The Tray Cover Assembly is an OEM part for LG refrigerators. It is designed to cover compartments within the refrigerator, such as crisper drawers or specific storage trays. This assembly helps maintain optimal humidity levels and temperatures in covered sections, enhancing the preservation of fruits, vegetables, and other perishables. 

Symptoms of a bad Tray Cover Assembly include:

• Cracks or breaks in the cover, which can compromise its structural integrity and aesthetic appearance,
• Difficulty fitting the cover properly in its designated space,
• Condensation issues or improper sealing that affects food preservation.

Causes of tray cover assembly damage often include mishandling, excessive weight placed on the cover, or degradation from frequent cleaning and exposure to food acids.

This OEM LG part is also compatible with Sears/Kenmore.

This refrigerator glass shelf replaces a cracked, broken, or missing shelf to restore safe, level storage space. It provides a sturdy surface for food containers and helps keep the compartment organized so you can use the full capacity again.

• Provides a flat, stable surface for storing food and containers
• Replaces damaged or missing shelf glass
• Restores original shelf capacity and organization
• Typical symptoms include cracked or shattered glass, an unstable/tilting shelf, and reduced usable space

• Remove items from the area and support the shelf with both hands when removing or installing
• Slide the shelf into the designated supports/rails until fully seated and level
• Handle glass carefully; wear gloves and avoid applying pressure to edges or corners
• Verify the shelf is secure before reloading items

Replacement tray assembly for the fresh food compartment. Restores a flat storage surface and helps contain spills, keeping produce organized and supported in the refrigerator's fresh area. What it does:

• Provides a stable shelf surface in the fresh food compartment for bins and produce.
• Helps contain minor spills and drips, preventing them from spreading to lower compartments.
• Replaces cracked, warped or damaged trays that cause items to tip or slide.
• Restores proper seating/support where a worn tray prevents drawers or bins from aligning.

• Disconnect power to the appliance or unplug the refrigerator before starting any service.
• Typically slides or snaps into place; may be secured with clips or screws depending on model.
• Handle carefully to avoid damage to plastic mounting tabs; inspect mounting points for wear before installing.

This door gasket assembly creates the airtight seal around a refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn or damaged seal to help keep food fresher and reduce moisture buildup. What it does:

• Seals the door to prevent warm air from entering the cabinet
• Helps maintain consistent internal temperature and cooling performance
• Reduces frost or condensation caused by a leaking seal
• Can stop drafts, rattling doors, and excessive run-time tied to a bad seal

• One door gasket assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the old gasket and clean the door frame before installing the new seal
• Press the gasket into the channel and secure per manufacturer clips/screws; warm the gasket slightly if needed for easier positioning
• After installation, check the seal around the full perimeter and adjust or retorque fasteners as required

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

The Refrigerator Set Screw is an OEM part for LG refrigerators. This small but crucial component is used to secure various parts of the refrigerator, ensuring stability and proper alignment of the internal components. This set screw is sold individually.

Causes of a bad set screw can include stripping due to over-tightening, corrosion from moisture exposure, or wear and tear over time. A loose or missing set screw can lead to instability and misalignment of the refrigerator parts, potentially causing operational issues.

Symptoms of a bad refrigerator set screw include:

• Loose or wobbly internal components
• Doors not closing properly or misaligned
• Unusual noises from inside the refrigerator
• Parts becoming detached or misaligned

This OEM LG part is also compatible with Sears/Kenmore models.

This is the magnetic door gasket that seals the refrigerator compartment to keep cold air in and warm air out. A tight seal helps maintain temperature, reduce frost/condensation, and improve energy efficiency.

• Creates an air-tight seal between the refrigerator door and cabinet
• Helps prevent sweating, frost, and temperature fluctuations
• Common failure signs: torn or deformed gasket, gaps, door not sealing, visible condensation around the door
• Can reduce excessive run time caused by air leaks

• Unplug the refrigerator before starting; remove food items from the door
• Warm the new gasket (room temp or warm water) to relax bends; do not overheat
• Work from corners first, pressing the gasket fully into the retainer/channel; some models require loosening/tightening inner liner screws
• Close the door and check for even contact all around; adjust as needed

A replacement pitcher guide that secures the water pitcher or pitcher-style container in the refrigerator door, helping keep the pitcher aligned and stable for smooth door operation and organized storage. What it does:

• Holds and aligns the refrigerator pitcher so it sits securely in the door bin.
• Reduces pitcher movement, rattling and tipping that can occur when opening or closing the door.
• Prevents the pitcher from shifting and potentially obstructing the door or other bins.

• Often snaps into the door bin or slides into a track; you may need to remove the bin or liner to access the guide.
• Use basic hand tools if required and avoid forcing parts to prevent damage.
• Follow the refrigerator service manual or OEM instructions for model-specific removal/installation steps.
• Disconnect power or follow safety guidance in the service manual when working near electrical components.

Replace a cracked or missing bin on your refrigerator door with this door basket assembly. It restores safe, organized storage so condiments, jars, and bottles stay upright, visible, and easy to reach.

• Mounts to the inner door liner to hold bottles, jars, and small items
• Helps keep contents upright during door opening/closing
• Direct replacement for damaged, warped, or missing bins
• Common symptoms: bin won't stay seated, broken tabs, loose/sagging fit, or tipping items

• Remove items from the old bin and lift straight up to release it from the door slots
• Align the new bin's hooks/tabs with the slots and press down until fully seated
• Confirm a secure fit before loading; distribute weight evenly and avoid overloading
• Handle plastic carefully; allow the bin to reach room temperature before installation if delivered cold

This door basket is the bin that mounts on the refrigerator door to hold bottles, condiments, and small items. Replacing a cracked or loose bin restores secure, organized door storage and helps prevent spills or items falling.

• Provides stable, easy-access storage on the refrigerator door
• Replaces a broken, missing, or loose door bin
• Common symptoms: cracked plastic, broken locking tabs, won't stay seated, falls off the door
• Helps keep smaller containers upright and organized

• Remove items from the old bin; lift it up and out of the door liner slots
• Align the new bin's hooks with the door guides for the intended position and press down until fully seated
• Verify it is locked in place before loading; avoid overloading

The Door Basket is an OEM part for LG refrigerators. It provides additional storage space on the refrigerator door, allowing for the organization and easy access to items such as bottles, jars, and condiments. The basket is designed to fit securely into the door, maximizing the available storage area.

Causes of a bad door basket can include wear and tear from regular use, cracks or breaks due to overloading, or damage from accidental impacts. These factors can compromise the basket's ability to hold items securely.

Symptoms of a bad door basket include:

• Cracks or breaks in the basket material
• Items not staying in place or falling out when the door is opened
• Difficulty in fitting the basket securely onto the door

This OEM LG part is also compatible with Sears/Kenmore.

The Door Closing Cam is an OEM part for LG refrigerators. This part ensures the refrigerator door closes smoothly and securely. It helps guide the door into the correct position and ensures a tight seal, which is essential for maintaining the internal temperature and efficiency of the appliance.

Causes of a bad door closing cam can include wear and tear over time, damage from repeated use, or accidental impacts that can misalign or break the cam. 

Symptoms of a bad Door Closing Cam include:

• The door not closing properly or securely
• Difficulty in opening or closing the door
• Unusual noises when operating the door
• Misalignment of the door

This OEM LG part is also compatible with some Kenmore models.

This is the small trim cap that snaps over the end of a refrigerator door handle. It finishes the handle, covers the mounting hardware, and helps keep the handle secure and looking clean.

• Covers exposed door-handle screws and mounting points
• Restores a finished appearance if the original cap is missing or damaged
• May help reduce handle looseness if the old cap no longer held properly
• Common symptoms: missing end cover, visible handle screws, loose or rattling handle

• Unplug the appliance before starting and open the door for access
• Remove the old cap by gently prying at the seam; avoid scratching the door finish
• Align the new cap with the handle end and press until it snaps fully into place
• If required, tighten handle mounting screws before installing the cap

This plastic freezer door hinge cover protects the hinge area and gives the freezer a finished look. It snaps into place to hide the hinge hardware and helps keep dirt and moisture away from the hinge assembly. What it does:

• Covers and protects the freezer door hinge and exposed hardware
• Helps prevent dirt, dust and moisture from contacting hinge components
• Restores finished appearance after hinge repair or installation
• Useful when replacing a worn, cracked or missing hinge cover

• One freezer door hinge cover

• Snap-on cover; usually installs without tools by pressing over the hinge post
• Remove any debris before installing to ensure a secure fit
• If hinge hardware is loose or damaged, replace/repair hinge first for proper alignment
• Disconnect power only if working near electrical components; otherwise power disconnection not typically required

This hinge cover protects and conceals the door hinge area, restoring a clean, finished look and helping keep debris away from the hinge. Replace a cracked, loose, or missing cover to refresh appearance and protect the hinge.

• Conceals exposed hinge hardware for a neat, finished appearance
• Helps shield the hinge area from dust and debris
• Helps prevent snags or rubbing around the hinge during door operation
• Common signs it's needed: cracked or broken plastic, loose/missing cover, cosmetic damage near the hinge

• Disconnect power to the appliance before servicing
• Open the door to access the hinge area; support the door if needed
• Remove the old cover by releasing its clips or screws; retain any fasteners
• Align the new cover and snap or fasten it in place; verify it sits flush and doesn't rub

This factory service kit groups the exact components specified for a model-specific repair. Installing the matched set together restores proper fit and operation while avoiding mismatched parts and repeat trips. What it does:

• Replaces the designated group of parts for the applicable subsystem on your appliance
• Helps resolve improper operation, unusual noise, or visible damage in that area
• Ensures consistent fit and performance with matched factory components
• Supports a single, efficient repair by refreshing related wear items at once

• 1 kit assembly

• Disconnect power; if applicable, turn off water and/or gas before servicing
• Follow your model's service manual and transfer parts one-for-one
• Use appropriate PPE and keep track of screws and small hardware
• Test the appliance fully after reassembly to ensure proper operation

Note: Top LEFT Hinge

Note: Top RIGHT hinge

A small plastic hinge cap that covers and protects a refrigerator/freezer door hinge, restoring a finished appearance and shielding the hinge from dust and debris. Simple replacement for a cracked, broken, or missing cap. What it does:

• Covers the exposed door hinge to improve appearance and protect moving parts
• Helps keep dirt, lint, and debris out of the hinge area
• Prevents sharp or rough hinge edges from catching on clothing or food-packaging
• Replaces cracked, broken, or missing hinge caps that leave the hinge exposed

• Support or brace the door before removing or replacing hinge covers to avoid door movement
• Use basic hand tools as needed; remove nearby trim or screws per the appliance service instructions
• Check fit and orientation before tightening any fasteners; do not force or snap parts beyond their designed engagement

This hinge cap protects and covers the refrigerator door hinge, keeping the hinge area clean and helping the door operate smoothly. A small replacement that restores a finished look and prevents debris from entering the hinge. What it does:

• Covers the exposed hinge to protect it from dirt, dust, and spills
• Helps maintain proper door alignment by keeping hinge components shielded
• Stops cosmetic damage to the hinge area and improves appearance
• Reduces hinge noise caused by debris in the hinge pocket

• High-level, safety-first: unplug or disconnect power to the appliance before servicing if work may contact electrical components
• Support the door or have a helper when removing or reinstalling hinge-related parts to prevent dropping or misalignment
• Use basic hand tools as needed; avoid forcing parts—inspect mating surfaces before reinstalling the cap
• If hinge damage or significant wear is present, replace the entire hinge assembly rather than only the cap

A small plastic hinge cap that covers and protects the refrigerator door hinge, keeping the hinge area tidy and helping prevent dirt buildup. Replaces damaged or missing caps to restore the door's finished appearance. What it does:

• Covers the exposed door hinge mount to protect it from dust and grime
• Helps maintain proper hinge alignment by keeping the hinge area clear
• Restores the cabinet's finished look when the original cap is cracked or missing
• Compatible with the corresponding LG hinge assembly and hardware

• One hinge cap

• Disconnect power to the appliance before performing service to avoid injury
• Remove any door trim or screws as required by your model to access the hinge cap
• Press or snap the cap into place over the hinge; replace damaged mounting clips if needed

The Hinge Bushing is an OEM part for LG refrigerators. It serves as a crucial component in the door hinge mechanism, ensuring smooth and stable operation when opening and closing the refrigerator door.

You should replace this hinge bushing if it becomes worn out or damaged. Common causes of a bad hinge bushing include constant use leading to wear and tear, misalignment of the door, or physical damage due to impact.

Symptoms of a bad hinge bushing include:

• Difficulty in opening or closing the door
• The door sagging or not aligning properly
• Unusual noises like squeaking or grinding when the door is moved

This OEM LG part is also compatible with Sears/Kenmore.

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

The Compressor Overload Protector Assembly is an OEM part for LG refrigerators. The compressor overload protector steps in if the compressor motor draws excessive current. It then interrupts the power to prevent overheating. The wire harness boosts the compressor to kick-start it, disengaging as soon as the motor reaches the desired speed.

Over time, the compressor overload protector can wear out or become damaged due to electrical issues, power surges, or constant exposure to high temperatures. A faulty protector can compromise the safety and efficiency of the refrigerator’s cooling system.

Symptoms of a bad compressor overload protector assembly include:

• The refrigerator not cooling properly
• The compressor frequently cycling on and off
• Clicking noises coming from the compressor area
• The refrigerator not turning on at all

This OEM LG part is also compatible with Sears/Kenmore models.

The Overload Compressor is an OEM part for LG refrigerators. This part protects the refrigerator's compressor from overheating and potential damage by acting as a safety device. It works by monitoring the compressor's electrical current and temperature. If the compressor operates under conditions that could lead to overheating or overcurrent, the overload protector will cut off the power to the compressor, allowing it to cool down before potentially restarting.

Causes of damage to the Overload Compressor can include power surges, electrical faults within the refrigerator, or a malfunctioning compressor that requires more current than usual to operate. 

Symptoms of a bad Overload Compressor include:

• The refrigerator not cooling properly or not cooling at all
• The compressor failing to start, indicated by a clicking sound coming from the back of the refrigerator where the compressor is located.
• The refrigerator or freezer section warming up

This OEM LG part is also compatible with some Kenmore models.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This replacement condenser assembly includes the attached wiring harness that secures and connects condenser-area components. It restores the factory wiring path for the condenser and associated electrical connections to help re-establish proper operation. What it does:

• Provides the condenser mounting/connection assembly and pre-attached wire harness for condenser-area components
• Restores factory routing and connector locations for reliable electrical connections
• Commonly replaced when condenser-area wiring is damaged, frayed, or disconnected
• Can resolve symptoms such as cooling loss, intermittent condenser fan operation, or electrical faults localized to the condenser area

• One condenser assembly with attached wire harness

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the rear service panel; keep fasteners and grounding in mind
• Match connectors and wire routing to the original layout; avoid pinching or sharp bends

This fan assembly circulates air through the appliance so coils and internal components operate at the proper temperature. Replacing a failed or noisy fan can restore airflow and help prevent performance issues caused by weak circulation.

• Moves air across coils and components to support designed cooling/dehumidifying performance
• Helps maintain steady airflow to reduce overheating or icing conditions
• A failing fan can cause little to no airflow even when the unit is running
• Common symptoms: fan not spinning, intermittent operation, loud rattling/grinding, vibration, or thermal shutdown

• Disconnect power before servicing to avoid electrical shock or injury
• Access the fan area per your unit's service information; remove panels/shrouds as needed
• Note wire connections and mounting order; transfer any brackets, grommets, or hardware from the old assembly
• After installation, ensure the fan spins freely and clears all shrouds, then test operation before reassembly

The Defrost Control Assembly is an OEM part for LG refrigerators, crucial for regulating the defrost cycle within the unit. This component plays a pivotal role in ensuring that the evaporator coils are periodically defrosted, preventing the build-up of ice that can impede airflow and cooling efficiency. 

Causes of a bad Defrost Control Assembly can include electrical failures, sensor malfunctions, or damage to the assembly itself, which can disrupt the defrost cycle.  

Symptoms of a bad Defrost Control Assembly include:

• The refrigerator or freezer compartment becoming too warm due to blocked airflow from ice accumulation
• A noticeable build-up of frost or ice on the evaporator coils or in the freezer compartment
• The refrigerator running continuously without cycling off
• Unusual noises coming from the refrigerator as ice builds up and interferes with the fan

This OEM LG part is also compatible with Sears/Kenmore.

The Door Switch is an OEM part for LG refrigerators. It is located near the door hinge and is activated by the door's movement. When the door is closed, the switch is engaged, allowing the interior light to turn off and other functions to operate normally. When the door is opened, the switch is released, triggering the interior light to turn on and potentially activating other features, such as the ice dispenser or cooling system.

Causes of a faulty door switch can include wear and tear over time, mechanical damage from excessive force, or electrical issues.

Symptoms of a bad door switch may include:

• The interior light not turning on when the door is opened
• The interior light remains on when the door is closed
• Issues with the dispenser or other functions associated with the door switch

The Fan Motor is an OEM part for LG refrigerators. It is essential for circulating air throughout the refrigerator and freezer compartments, ensuring that the temperature is evenly distributed and maintained at the set levels. This motor powers the fan that helps to cool the evaporator coils and dissipate heat, which is vital for the appliance's cooling efficiency.

Symptoms of a failing Fan Motor include:

• The refrigerator not cooling adequately
• Unusual noises coming from the refrigerator, such as humming or buzzing
• Ice buildup in the freezer compartment due to poor air circulation
• The refrigerator cycling on and off more frequently

Causes of a bad fan motor can include wear and tear over time, obstructions in the fan blades, or electrical issues such as faulty wiring or a malfunctioning capacitor.

This OEM LG part is also compatible with Sears/Kenmore.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

The Refrigerator Door Switch is an OEM part for LG refrigerators, designed to signal the control system when the door is open or closed. This small but essential component plays a critical role in the overall operation of your refrigerator, including the activation of interior lights and the control of cooling functions. 

Over time, the door switch can fail due to mechanical wear, accidental damage, or a buildup of debris that may prevent it from functioning correctly. 

Symptoms of a bad Refrigerator Door Switch include:

• Interior lights not turning on or off appropriately with the door's position
• The refrigerator running longer than necessary, potentially leading to increased energy bills
• Unusual fluctuations in temperature inside the fridge, affecting food preservation

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Compressor Run Capacitor is an OEM part for LG refrigerators. It plays a critical role in the operation of the refrigerator's compressor by providing the necessary electrical boost to start and maintain the compressor's operation.

Causes of a bad compressor run capacitor can include electrical surges, overheating, or simply wear and tear over time. When the capacitor fails, it can no longer deliver the required electrical charge, which impacts the compressor's ability to start and run efficiently.

Symptoms of a bad compressor run capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual humming or clicking noises from the compressor area
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

This power cord assembly supplies AC power from the wall outlet to your appliance. Replacing a frayed, heat-damaged, or loose cord restores safe, reliable operation and can eliminate intermittent power loss.

• Carries line voltage and ground into the unit to power controls and components
• Routes electricity safely into the cabinet to protect internal wiring
• Replace at the first sign of damage to reduce shock or fire risk

• Disconnect power at the outlet/breaker before servicing
• Compare the new cord to the original; transfer any clips or grommets from the old cord if needed
• Route and secure the cord exactly as original; keep clear of sharp edges and moving parts
• Ensure all connections are fully seated and the ground is properly secured before restoring power

The Compressor Overload Protector Assembly is an OEM part for LG refrigerators. The compressor overload protector steps in if the compressor motor draws excessive current. It then interrupts the power to prevent overheating. The wire harness boosts the compressor to kick-start it, disengaging as soon as the motor reaches the desired speed.

Over time, the compressor overload protector can wear out or become damaged due to electrical issues, power surges, or constant exposure to high temperatures. A faulty protector can compromise the safety and efficiency of the refrigerator’s cooling system.

Symptoms of a bad compressor overload protector assembly include:

• The refrigerator not cooling properly
• The compressor frequently cycling on and off
• Clicking noises coming from the compressor area
• The refrigerator not turning on at all

This OEM LG part is also compatible with Sears/Kenmore models.

This sheath heater is the heating element used in compatible electric dryers to generate hot air for drying. Replaces a worn or failed heater element to restore normal drying performance and reduce extended dry times. What it does:

• Heats air inside the dryer cabinet so clothes can dry efficiently.
• Commonly linked to symptoms like clothes not drying, extended drying cycles, or no heat from the dryer.
• Works with the dryer's thermostats and thermal fuses; a faulty heater can mimic other heat-related failures.

• Disconnect power at the breaker before servicing — this part involves live AC voltage.
• Inspect and replace any open thermal fuses or failed thermostats at the same time as recommended by the model service guide.
• Handle the element carefully to avoid bending or damaging the sheath; follow OEM instructions and torque specs during reassembly.

This cover assembly protects the appliance's printed circuit board from debris, moisture and accidental contact, helping preserve reliable control operation. It provides a secure enclosure that keeps the PCB mounted and shielded during normal use. What it does:

• Shields the control board from dust, moisture splash and foreign objects that can cause shorts or component damage.
• Keeps wiring and connectors routed and secured to reduce strain and intermittent connections.
• Helps maintain correct spacing and alignment of the PCB for reliable electrical contacts.
• Useful when the original plastic cover is cracked, warped, missing or allows board exposure.

• One cover assembly for PCB.

• Disconnect power to the appliance before beginning any service to avoid shock or damage.
• Handle the PCB and connectors carefully; avoid touching board components or bending traces.
• Align cover over the PCB and fasten with the original screws or clips; do not overtighten plastic fasteners.

The Ice Maker Assembly Kit is an OEM part for LG refrigerators. This kit includes all the components necessary to produce ice efficiently, ensuring a steady supply of ice cubes for your household needs. This particular 12-cube ice maker assembly features a 10-wire harness. 

Causes of a bad ice maker assembly can include wear and tear over time, issues with the water supply, or mechanical malfunctions that prevent the ice maker from operating correctly. These issues can lead to a reduction in ice production or complete failure of the ice maker.

Symptoms of a bad ice maker assembly include:

• No ice production
• Ice cubes being smaller than usual
• Leaks around the ice maker area
• Unusual noises during the ice-making process

This OEM LG part is also compatible with Sears/Kenmore.

A compressible foam gasket that restores a tight seal between panels to help prevent air or water leaks, reduce vibration and noise, and improve overall sealing performance. Replaces worn or damaged foam seals to help appliances operate as intended. What it does:

• Forms a compressible seal to block air and moisture from leaking between mating surfaces.
• Helps reduce vibration, rattles and panel movement by cushioning contact points.
• Limits condensation and localized frost or moisture buildup caused by gaps in seals.
• Common signs you may need this part: visible gaps or torn foam, unusual noise from panels, or moisture where parts meet.

• Disconnect power (and water, if applicable) before beginning service.
• Remove trim or panels carefully to access the old gasket; keep hardware for reuse.
• Clean and dry mating surfaces before fitting the new gasket; press evenly into place for a continuous seal.

The Inlet Water Valve Assembly is an OEM part for LG refrigerators, designed to manage the flow of water into the refrigerator's ice maker and water dispenser. This part ensures that your refrigerator provides clean, fresh water and ice on demand by controlling the water pressure and flow through the system. The valve assembly is key to maintaining the refrigerator's functionality and the freshness of the water and ice it dispenses.

Causes of a bad Valve Assembly, Water can include mineral build-up from hard water, which can block the valve and prevent it from opening or closing properly. 

Symptoms of a bad Valve Assembly include:

• No water dispensed
• Leaking water from the refrigerator
• Ice maker not producing ice
• Strange noises coming from the refrigerator when the dispenser is used

This OEM LG part is also compatible with some Kenmore models.

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

The Temperature Sensor is an OEM part for LG refrigerators. It monitors the internal temperature and sends this information to the control board, ensuring that the refrigerator maintains the correct temperature for optimal food preservation.

Over time, temperature sensors can fail due to electrical issues, exposure to moisture, or wear and tear from continuous use. 

Symptoms of a bad temperature sensor include:

• Inaccurate temperature readings
• The refrigerator or freezer being too warm or too cold
• The refrigerator running constantly or not running at all
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances.