Parts for Lg LDCS22220S/00: Other Parts

This screw is a direct-fit replacement fastener that secures panels, brackets, and internal components. Replacing a missing or stripped screw helps stop rattling and keeps parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets, or internal components to restore proper fit
• Replaces missing or damaged hardware that can cause rattling or loose parts
• Restores alignment so doors, shelves, or assemblies operate smoothly
• Provides a straightforward hardware fix without replacing larger assemblies

• Use the matching screwdriver or driver bit to avoid stripping the head
• Do not overtighten — snug until seated to avoid damaging threads or plastic parts
• Disconnect power or follow appliance safety instructions before servicing electrical areas
• Keep removed hardware organized and save any damaged parts for inspection

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This adjustable leveling leg assembly supports and stabilizes the refrigerator. Replacing a worn or damaged leg restores proper leveling, reduces vibration and noise, and helps doors align and seal correctly.

• Provides height adjustment at the cabinet corner to level the appliance on uneven floors
• Helps prevent rocking, rattling, and excessive vibration
• Promotes proper door alignment and gasket sealing
• Replace if the foot is broken, missing, bent, or the threads are stripped and won't hold adjustment

• Disconnect power and turn off the water supply before servicing
• Protect the floor; with a helper, carefully tip and support the refrigerator
• Unscrew the old leg; hand-thread the new leg, then fine-tune height with a wrench until level
• Ensure both front legs share the load evenly and recheck door operation

This rail holder secures the oven/microwave slide rail so racks or trays move smoothly and stay aligned. Replacing a worn holder restores stable sliding and prevents rails from coming loose during use. What it does

• Holds and supports the slide rail so racks glide in and out without sagging
• Replaces cracked or broken holders that allow the rail to shift or detach
• Helps stop scraping, binding or uneven rack movement caused by a damaged support
• Works as the small mounting point that keeps the rail seated and aligned

• One rail holder as shown

• Disconnect power to the appliance before servicing to avoid shock
• Inspect matching rail and mating surfaces; replace any additional damaged hardware
• Usually accessible by removing the interior trim or rail end caps; reinstall in the correct orientation
• Tighten fasteners snugly but avoid over-torquing plastic parts

A replacement rail holder that secures the rail/roller assembly so the turntable or sliding rail operates smoothly and stays aligned. Restores stable support and reduces wobble or uneven rotation. What it does

• Secures the rail or roller guide to the appliance chassis so the tray or sliding assembly stays centered.
• Helps prevent grinding, scraping or uneven turntable rotation caused by a loose or broken holder.
• Reduces noise and vibration that can occur when the rail assembly is not held firmly.
• Useful when the original rail support is cracked, worn, or missing.

• Disconnect power to the appliance before beginning any work.
• Remove the glass tray or any panels blocking access to the rail area before replacing the holder.
• Typically fastens with standard screws; keep hardware and orientation consistent with the removed part.

The Guide Assembly Rail (RH) is an OEM part for LG refrigerators. This Right-hand rail is responsible for guiding the movement of drawers or shelves within the refrigerator, ensuring smooth and secure sliding. It helps maintain proper alignment and stability of the drawers, making it easier to access stored food items.

Causes of a bad guide rail can include wear and tear over time, damage due to heavy loads or excessive force when opening and closing the drawers, or misalignment from improper installation. A faulty rail can affect the performance of the drawer, leading to difficulties in accessing the refrigerator’s contents.

Symptoms of a bad guide rail include:

• Drawers not sliding in and out smoothly
• Misaligned or wobbly drawers
• Difficulty opening or closing drawers completely

This OEM LG part is also compatible with Sears/Kenmore.

The Guide Assembly, Rail (LH) is an OEM part for LG refrigerators. This component is located within the fridge compartment and is responsible for guiding and supporting the bottom drawer, ensuring it opens and closes smoothly along the right-hand side. The guide rail assembly helps the drawer maintain proper alignment and prevents it from tilting or binding during operation.

Causes of a bad guide rail assembly can include wear and tear from regular use, damage from overloading the drawer, or accidental impacts that may bend or misalign the rail.

Symptoms of a bad Guide Assembly, Rail (LH) include:

• Difficulty opening or closing the drawer
• The drawer not aligning properly
• Unusual noises when opening or closing the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

This is the ice bucket that stores ice dispensed by your refrigerator's ice maker. A cracked, warped, or stuck bin can jam the auger or spill ice, leading to poor dispensing and messy freezers.

• Holds and dispenses harvested ice from the ice maker to the door chute or bin access
• Common failure signs: cracked bucket, ice not dispensing, auger not turning, ice clumping or spilling
• Restores smooth ice dispensing and proper storage in the freezer
• Built to fit the original mounting and drive interface for an easy swap

• Unplug the refrigerator and wear cut-resistant gloves
• Remove the old bin carefully; thaw any ice buildup before transferring
• Inspect the auger drive coupling for wear before installing the new bucket
• Seat the bucket fully so the drive engages; test dispense with a small amount of ice

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This roller is the small wheel that lets a sliding component move smoothly along its track. Replacing a worn or cracked roller restores easy, quiet operation and helps prevent binding, noise, and uneven travel.

• Supports and guides a moving bin, drawer, or rack on its track
• Reduces friction for smooth, even motion
• Common symptoms: sticking or hard-to-open movement, grinding/clicking noises, wobbling/misalignment, or a cracked/missing wheel
• Helps protect tracks and brackets from excess wear

• Disconnect power before servicing; wear gloves to protect hands
• Remove the sliding component to access the roller
• Release the clip/fastener, install the new roller, and transfer/reuse original hardware if applicable
• Test movement to ensure the roller is fully seated and tracking correctly; replace in pairs when applicable for even travel

Roller assembly approx. 2".

This is the freezer drawer tray that sits inside the pull-out freezer compartment. It provides a stable, food-safe surface to organize and support frozen items and slides with the drawer for easy access.

• Holds and organizes frozen foods within the freezer drawer
• Helps maintain proper drawer operation and storage capacity
• Replace if cracked, warped, or missing
• Common signs include broken corners, instability, or items falling through

• Unplug the appliance and wear cut-resistant gloves
• Fully open the freezer drawer and remove any food items
• Lift out the old tray; seat the new tray into the supports
• Ensure it is level and slides smoothly with the drawer before use

This rail holder secures the microwave door rail so the door stays aligned and operates smoothly. Replaces a worn or broken holder to reduce door wobble and improve closing action. What it does:

• Secures and supports the door rail assembly for proper door alignment
• Keeps the rail from shifting, preventing rubbing, rattling or uneven gaps
• Helps restore smooth opening and closing of the door
• Fits where the rail mounts to the door frame or trim

• One rail holder

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools (screwdriver/trim tool) and handle plastic parts gently to avoid breakage
• Inspect surrounding clips/rails for damage and replace if needed for a lasting repair

This rail holder is the replacement support that secures an appliance rail in place, restoring proper alignment and smooth movement. It helps keep sliding components stable so drawers or rails track correctly and safely. What it does:

• Secures the rail or slide to the appliance frame to prevent sagging or misalignment
• Restores smooth, controlled movement of sliding parts
• Helps eliminate rattling, binding or uneven travel caused by a loose or broken holder
• Works as a direct-fit support when the original holder is damaged or worn

• Disconnect power and remove any movable components before beginning work
• Installation typically requires basic hand tools; keep fasteners from the original part for reuse if undamaged
• Inspect adjoining rails, slides and mounting points; replace any damaged hardware for best results

A replacement glide rail assembly that supports and guides a refrigerator/freezer drawer for smooth opening and closing. Restores proper drawer tracking and helps prevent sticking or misalignment. What it does:

• Provides the rail and mounting components that the drawer slides on for stable operation
• Restores smooth drawer movement and alignment when original rail is bent or worn
• Helps reduce drawer sticking, scraping, or uneven travel
• Intended for use where the OEM glide/rail assembly is specified

• One glide rail assembly

• Follow the appliance manufacturer's service manual for removal and installation steps
• Disconnect power and empty the drawer before working to prevent injury or damage
• Inspect mounting hardware and drawer slides; replace any damaged fasteners
• Use basic hand tools;

This guide assembly rail replaces a worn or damaged drawer slide to restore smooth, stable drawer movement and proper alignment. It helps reduce sticking, misalignment, and rattling for a secure fit and quiet operation. What it does:

• Guides and supports the drawer or compartment during open/close cycles
• Restores smooth sliding action and consistent alignment
• Reduces noise caused by worn or bent rails or guides
• Helps prevent drawers from catching or binding

• Disconnect power and empty the drawer before beginning service
• Removal of the drawer and access panel may be required; keep fasteners for reassembly
• Align the rail before tightening fasteners; use basic hand tools

This rail guide assembly replaces a worn or damaged drawer/rack guide to restore smooth, stable movement and help prevent the rack or drawer from binding or coming off track. Fits original mounting points for a direct replacement. What it does:

• Guides and supports the drawer or rack so it slides in and out smoothly
• Helps keep the rack/drawer aligned to prevent derailment or sticking
• Replaces broken or worn plastic or metal guide components that cause noisy or rough movement
• Restores intended fit and function of the sliding mechanism

• Disconnect power and remove contents from the drawer/rack before starting any work
• Basic hand tools may be required; follow OEM instructions for orientation and attachment
• Inspect mating slides and fasteners; replace any damaged clips or screws for secure fit

This genuine replacement knob shutter restores the control panel's knob opening and protects internal switches from debris while allowing knobs to engage properly. It helps maintain smooth knob operation and reduces dirt buildup behind the control surface. What it does:

• Covers the knob opening and guides the control knob into place for reliable engagement
• Protects internal switches and electronics from dust, crumbs, and spills
• Helps prevent accidental knob movement when not in use
• Restores proper fit and appearance of the control panel area

• One knob shutter

• Power off and unplug the appliance before beginning any work to avoid electrical shock
• Small fasteners or clips may need to be removed; use appropriate hand tools and keep track of hardware

Replace a cracked or missing produce bin so fruits and vegetables store at the proper humidity and your fridge stays organized. This direct-fit crisper drawer restores clean, reliable storage in the fresh-food section.

What it does

• Stores produce at a humidity level intended for fruits and vegetables
• Restores smooth pull-out/push-in operation when paired with intact slides
• Helps prevent spills and items dropping behind the drawers
• Replaces damaged bins that stick, wobble, or won’t seat correctly

What’s included
One vegetable/crisper drawer (sold individually).

Install notes

• Slide the old bin straight out; align and seat the new bin on the guides—no tools required
• Do not force; ensure the rail guides and center track are fully engaged
• Hand-wash only; avoid harsh cleaners that can stress and crack plastics

Usage tip
Keep heavier items on shelves above; overloading the bin can crack corners and stress the rails.

Restore a clean, reliable produce bin. This crisper drawer (vegetable tray) replaces cracked or missing bins so fruits and vegetables store properly and your fridge stays organized with smooth pull-out access.

What it does

• Provides dedicated produce storage in the fresh-food compartment
• Helps maintain proper humidity when used with the crisper cover
• Restores smooth slide-in/slide-out operation
• Helps prevent spills and items dropping behind the drawers
• Replaces damaged bins that stick, wobble, or won’t seat correctly

What’s included
One vegetable/crisper drawer bin (sold individually).

Install notes

• Unplug power before moving shelves or covers
• Pull the old bin straight out; align and seat the new bin fully on the guides
• Inspect rails and the crisper cover for cracks before reuse
• Hand-wash only; avoid harsh cleaners or high heat that can stress plastics

Replace a cracked or missing drawer cover to restore clean, organized storage in the fresh-food section. This cover sits above the drawer and helps keep items contained with smooth, reliable access.

What it does

• Forms the top cover over a pantry/crisper-style drawer
• Helps contain spills and prevents items from dropping behind the drawer
• Restores smooth slide-in/slide-out operation when the frame tabs are intact
• Replaces covers with broken corners, warped frames, or missing supports

What’s included
One drawer cover (tray cover).

Install notes

• Remove the drawer, lift out the damaged cover, and seat the new cover on its supports—do not force
• If your model uses a separate glass insert, handle carefully and transfer only if applicable
• Reinstall the drawer and verify smooth travel and full seating on the rails

This supporter cover is a TV rear trim piece that protects and conceals internal components while restoring the set's appearance. It provides a finished look and covers the TV's support area for safe handling and cosmetic repair. What it does

• Covers and protects the TV's rear support area and nearby components from dust and incidental contact
• Restores the TV's exterior finish after damage or missing trim pieces
• Helps maintain correct spacing for the support/stand attachment area
• Common symptom: cracked, warped, missing, or loose rear trim exposing internal parts

• One supporter cover

• Unplug the TV and place it face down on a soft, non-abrasive surface before starting
• Installation may require removing screws or disengaging plastic clips; keep hardware organized
• Handle carefully to avoid scratching the display or bending mounting tabs
• Refer to the TV's service manual for disassembly instructions and torque/spec guidance

This replacement decor tray is the exterior trim panel that restores the finished look of the appliance and covers the underlying components for a clean, factory appearance. It's a direct-fit cosmetic part. What it does:

• Replaces a cracked, scratched or missing exterior trim piece to restore appearance
• Covers and protects control-area edges and hardware from everyday wear
• Helps keep the front of the appliance looking flush and factory-finished
• Fits into the surrounding trim and secures with existing fasteners or clips

• Disconnect power to the appliance before starting any work.
• Installation typically uses the existing clips or screws; handle trim gently to avoid scratching.
• Use the appliance service manual or parts diagram for correct removal/installation steps.
• If fasteners are damaged or missing, replace them with OEM-specified hardware.

The Refrigerator Decor Assembly is an OEM replacement part for LG refrigerators. This cover is attached to the front of the deli drawer. It helps to maintain the cleanliness and freshness of the food items stored in the drawer. It also helps to protect the drawer from damage.

This part fixes the following symptoms:

• Difficulty opening and closing the deli drawer
• Damaged or missing cover
• Cracked, faded, or scratched cover

Causes of a bad decor assembly can include accidental damage during cleaning or use, degradation of materials over time, or improper installation causing misalignment.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Glass Shelf is an OEM replacement part for LG refrigerators. It provides sturdy, clear storage for items inside the refrigerator compartment. The glass shelf is designed to seamlessly integrate into the shelf system, dividing interior space for easy organization.

Causes of a bad glass shelf can include cracks or chips from heavy items, damage due to impact or mishandling, or general wear and tear over time.

Symptoms of a bad glass shelf include:

• Cracks or chips in the glass that compromise its structural integrity
• Leaks or moisture inside the fridge from a damaged shelf
• The shelf no longer fitting or functioning properly in the shelf system

This OEM LG part is also compatible with Sears/Kenmore.

Replace a damaged or missing Fresh Room drawer with this tray assembly. It restores the dedicated storage area and smooth slide action in your refrigerator so items stay organized, contained, and easy to access. What it does:

• Forms the Fresh Room/deli compartment bin for organizing smaller items
• Slides on existing rails for easy access to contents
• Helps contain minor spills and keep foods separated
• Common symptoms: cracked or broken bin/tabs, warped edges, hard to slide, falls off tracks

• One fresh room tray assembly

• Disconnect power to the refrigerator before servicing
• Empty the compartment and remove the old tray by sliding it straight out
• Inspect/clean the rails or supports; align the new tray with the tracks
• Slide fully into place and check smooth movement before reloading

This is a replacement freezer door that restores the exterior panel and helps maintain proper sealing and appearance of the freezer compartment. It's a direct-fit outer door intended to replace damaged, dented, or worn freezer doors. What it does:

• Replaces a damaged or dented freezer door panel to restore proper closure and appearance
• Helps maintain the door seal and consistent internal temperature when paired with a good gasket
• Stops drafts and reduces moisture buildup caused by warped or bent doors
• Restores normal door operation when hinges and mounting points are intact

• Doors can be heavy and awkward
• Inspect existing hinges, screws, and gasket before installation; replace any damaged hardware
• Disconnect power to the appliance and remove contents from the door area before starting work
• Follow OEM instructions for alignment and torque to ensure a proper seal and smooth operation

This door gasket assembly replaces a worn or damaged door seal to restore a tight, reliable seal and help prevent leaks, drafts, and loss of performance. Fits as the appliance's door seal where specified. What it does:

• Replaces the door seal to restore a watertight/airtight barrier and reduce leaks
• Helps maintain proper internal temperature and efficiency by preventing air loss
• Reduces odors and residue buildup that can result from a compromised seal
• Supports correct door closure and alignment for reliable operation

• One door gasket assembly

• Disconnect power and water before starting any repair
• Follow the OEM service manual for removal, alignment, and reinstallation steps
• Inspect mounting flange, clips, and sealing surface; replace damaged hardware if found
• Use appropriate tools and avoid sharp objects that could tear the gasket; consider having a second person assist with alignment

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

The Refrigerator Set Screw is an OEM part for LG refrigerators. This small but crucial component is used to secure various parts of the refrigerator, ensuring stability and proper alignment of the internal components. This set screw is sold individually.

Causes of a bad set screw can include stripping due to over-tightening, corrosion from moisture exposure, or wear and tear over time. A loose or missing set screw can lead to instability and misalignment of the refrigerator parts, potentially causing operational issues.

Symptoms of a bad refrigerator set screw include:

• Loose or wobbly internal components
• Doors not closing properly or misaligned
• Unusual noises from inside the refrigerator
• Parts becoming detached or misaligned

This OEM LG part is also compatible with Sears/Kenmore models.

This door foam assembly is the pre-formed insulation used inside a refrigerator door to restore thermal performance and reduce cold spots. Replacing damaged or missing door foam helps the door maintain consistent cooling and reduces moisture buildup. What it does:

• Replaces the door's internal foam insulation to help maintain even temperatures across the door
• Reduces condensation or frost forming inside or around the door cavity
• Improves overall energy efficiency by restoring the door's insulating barrier
• Helps stabilize door panel fit and support interior components mounted to the door

• Disconnect power before starting and remove the door.
• Handle the foam carefully to avoid tearing or compressing; align inside the door cavity before reassembly.
• Use only manufacturer-recommended fasteners or adhesives if the original used any; do not rely on the foam as a structural fastener.
• After reassembly, test the door seal and refrigerator temperature for proper operation.

This drawer guide is the replacement rail that helps a freezer or refrigerator drawer open and close smoothly, restoring proper alignment and reducing sticking or grinding during use. Designed to match OEM fit and function. What it does:

• Guides the drawer along its track to ensure smooth, even movement
• Keeps the drawer aligned to prevent binding, rubbing, or tipping
• Reduces noise from scraping or catching when opening or closing
• Helps restore proper drawer seating and overall compartment accessibility

• One drawer guide (rail) as shown

• Inspect mating track and adjacent hardware for damage before installing
• Remove power or follow manufacturer safety guidance for accessing interior components
• Install with original fasteners; tighten securely but avoid over-torquing
• If multiple guides are worn or damaged, replace matching guides on the other side for best performance

This door basket assembly replaces a cracked, broken or loose refrigerator door bin to restore secure storage for bottles, jars and small containers. Durable plastic construction mounts to the inner door shelf. What it does:

• Replaces a damaged or missing door bin that won't hold items securely
• Restores organized storage on the refrigerator door for bottles and containers
• Secures to the door using factory mounting tabs to prevent shifting or falling
• Helps prevent spills and lost storage capacity caused by cracked bins

• Remove all items from the door shelf before installing the new basket.
• Align the basket's mounting tabs with the door slots, then press until it snaps into place; do not force broken tabs.
• Inspect door mounting points for damage; replace any broken clips or supports as needed.
• Wear gloves to protect hands from sharp edges and broken plastic during removal.

This Door basket is the replacement door insert that holds and secures items in the appliance door, restoring safe storage and proper closure. Designed to replace a cracked, broken, or missing door basket. What it does

• Provides a molded storage pocket inside the appliance door so small items stay in place.
• Restores proper alignment and fit of the door interior when the original basket is damaged.
• Helps prevent items from shifting, rattling, or falling out during use.
• Commonly replaced when the basket is cracked, warped, or detached from the door.

• One door basket.

• Disconnect power and follow the appliance service manual before beginning repair.
• Removal/installation may require removing the door trim or inner liner—support the door to prevent damage.
• Wear gloves to protect against sharp edges and handle plastic clips carefully to avoid breakage.

The Door Basket is an OEM replacment part for LG French door refrigerators. It is a removable, flexible storage basket mounted inside the refrigerator door panel. The basket provides easy access to commonly used ingredients directly from the door.

Causes of a failing basket can include cracked or broken mounting clips over time. 

Symptoms of an inadequate basket include:

• Inability to securely hold contents inside the fridge door 
• Detachment from fasteners allowing it to dangle
• Holes or damage reducing usable storage space

This OEM LG replacement basket is also compatible with some Kenmore models.

This door stopper limits and cushions the appliance door's travel to prevent overextension and damage to hinges or surrounding surfaces. Replacing a worn or broken stopper restores smooth, controlled door movement and consistent closing alignment.

• Limits door opening angle and provides a positive stop to prevent overextension
• Helps protect hinges and adjacent panels from impact or scuffing
• Promotes smoother opening/closing and more consistent door alignment
• Symptoms of a failed stopper can include over-swing, scraping/rubbing, clicking noises, or a loose "stop" feel

• Disconnect power to the appliance before servicing
• Open the door to access the stopper; support the door if necessary
• Remove the fastener/retainer, note the old stopper's orientation, and install the new stopper using existing hardware
• Slowly open and close the door to verify the stop action and clearances after installation

The Door Closing Cam is an OEM part for LG refrigerators. This part ensures the refrigerator door closes smoothly and securely. It helps guide the door into the correct position and ensures a tight seal, which is essential for maintaining the internal temperature and efficiency of the appliance.

Causes of a bad door closing cam can include wear and tear over time, damage from repeated use, or accidental impacts that can misalign or break the cam. 

Symptoms of a bad Door Closing Cam include:

• The door not closing properly or securely
• Difficulty in opening or closing the door
• Unusual noises when operating the door
• Misalignment of the door

This OEM LG part is also compatible with some Kenmore models.

RAIL,SLIDE-LEFT

RAIL,SLIDE-RIGHT

This connector assembly links refrigerator components with a secure, factory-style connection. Replace a damaged or loose connector to restore reliable operation and prevent intermittent performance of the part(s) attached to it. What it does:

• Joins two factory leads/components with a secure locking interface
• Restores a stable connection so the attached component operates reliably
• Helps address intermittent operation, no response, or flickering due to worn or heat-damaged connectors
• Replaces connectors with broken locking tabs, loosened contacts, or visible melting/corrosion

• 1 connector assembly

• Disconnect power before servicing; if working near water lines, also shut off the water supply
• Note connector orientation and routing; take photos to aid reassembly
• Depress the locking tab to release; avoid pulling on wires
• Seat the new connector fully until it locks; route away from sharp edges and moving parts

This plastic freezer door hinge cover protects the hinge area and gives the freezer a finished look. It snaps into place to hide the hinge hardware and helps keep dirt and moisture away from the hinge assembly. What it does:

• Covers and protects the freezer door hinge and exposed hardware
• Helps prevent dirt, dust and moisture from contacting hinge components
• Restores finished appearance after hinge repair or installation
• Useful when replacing a worn, cracked or missing hinge cover

• One freezer door hinge cover

• Snap-on cover; usually installs without tools by pressing over the hinge post
• Remove any debris before installing to ensure a secure fit
• If hinge hardware is loose or damaged, replace/repair hinge first for proper alignment
• Disconnect power only if working near electrical components; otherwise power disconnection not typically required

This hinge cover protects and conceals the door hinge area, restoring a clean, finished look and helping keep debris away from the hinge. Replace a cracked, loose, or missing cover to refresh appearance and protect the hinge.

• Conceals exposed hinge hardware for a neat, finished appearance
• Helps shield the hinge area from dust and debris
• Helps prevent snags or rubbing around the hinge during door operation
• Common signs it's needed: cracked or broken plastic, loose/missing cover, cosmetic damage near the hinge

• Disconnect power to the appliance before servicing
• Open the door to access the hinge area; support the door if needed
• Remove the old cover by releasing its clips or screws; retain any fasteners
• Align the new cover and snap or fasten it in place; verify it sits flush and doesn't rub

This factory service kit groups the exact components specified for a model-specific repair. Installing the matched set together restores proper fit and operation while avoiding mismatched parts and repeat trips. What it does:

• Replaces the designated group of parts for the applicable subsystem on your appliance
• Helps resolve improper operation, unusual noise, or visible damage in that area
• Ensures consistent fit and performance with matched factory components
• Supports a single, efficient repair by refreshing related wear items at once

• 1 kit assembly

• Disconnect power; if applicable, turn off water and/or gas before servicing
• Follow your model's service manual and transfer parts one-for-one
• Use appropriate PPE and keep track of screws and small hardware
• Test the appliance fully after reassembly to ensure proper operation

Note: Top LEFT Hinge

Note: Top RIGHT hinge

This hinge cap protects and covers the refrigerator door hinge, keeping the hinge area clean and helping the door operate smoothly. A small replacement that restores a finished look and prevents debris from entering the hinge. What it does:

• Covers the exposed hinge to protect it from dirt, dust, and spills
• Helps maintain proper door alignment by keeping hinge components shielded
• Stops cosmetic damage to the hinge area and improves appearance
• Reduces hinge noise caused by debris in the hinge pocket

• High-level, safety-first: unplug or disconnect power to the appliance before servicing if work may contact electrical components
• Support the door or have a helper when removing or reinstalling hinge-related parts to prevent dropping or misalignment
• Use basic hand tools as needed; avoid forcing parts—inspect mating surfaces before reinstalling the cap
• If hinge damage or significant wear is present, replace the entire hinge assembly rather than only the cap

A small plastic hinge cap that covers and protects the refrigerator door hinge, keeping the hinge area tidy and helping prevent dirt buildup. Replaces damaged or missing caps to restore the door's finished appearance. What it does:

• Covers the exposed door hinge mount to protect it from dust and grime
• Helps maintain proper hinge alignment by keeping the hinge area clear
• Restores the cabinet's finished look when the original cap is cracked or missing
• Compatible with the corresponding LG hinge assembly and hardware

• One hinge cap

• Disconnect power to the appliance before performing service to avoid injury
• Remove any door trim or screws as required by your model to access the hinge cap
• Press or snap the cap into place over the hinge; replace damaged mounting clips if needed

This center hinge assembly supports the refrigerator door at the mid-cabinet position. It carries the door's weight and provides a smooth pivot so the door aligns properly and the gasket seals as designed to help prevent rubbing and air leaks. What it does:

• Provides the middle pivot and vertical support for a refrigerator door
• Helps maintain door alignment for proper gasket contact and smooth opening/closing
• Wear or damage may cause door sagging, binding/squeaking, gaps, or poor sealing
• Restores correct door positioning after hinge wear or impact

• 1 center hinge assembly

• Disconnect power; protect floors and support the door with a helper
• Remove mounting screws, lift the door off, and take off the old hinge
• Transfer any spacers/shims/bushings from the old hinge if not pre-installed
• Install the new hinge in the same orientation; set door, tighten hardware, and verify alignment and gasket seal

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

NOTE: This part also requires software update kit CJT30000002. DO NOT INSTALL WITHOUT UPDATING SOFTWARE. Call for more information.

The Compressor Overload Protector Assembly is an OEM part for LG refrigerators. The compressor overload protector steps in if the compressor motor draws excessive current. It then interrupts the power to prevent overheating. The wire harness boosts the compressor to kick-start it, disengaging as soon as the motor reaches the desired speed.

Over time, the compressor overload protector can wear out or become damaged due to electrical issues, power surges, or constant exposure to high temperatures. A faulty protector can compromise the safety and efficiency of the refrigerator’s cooling system.

Symptoms of a bad compressor overload protector assembly include:

• The refrigerator not cooling properly
• The compressor frequently cycling on and off
• Clicking noises coming from the compressor area
• The refrigerator not turning on at all

This OEM LG part is also compatible with Sears/Kenmore models.

The Overload Compressor is an OEM part for LG refrigerators. This part protects the refrigerator's compressor from overheating and potential damage by acting as a safety device. It works by monitoring the compressor's electrical current and temperature. If the compressor operates under conditions that could lead to overheating or overcurrent, the overload protector will cut off the power to the compressor, allowing it to cool down before potentially restarting.

Causes of damage to the Overload Compressor can include power surges, electrical faults within the refrigerator, or a malfunctioning compressor that requires more current than usual to operate. 

Symptoms of a bad Overload Compressor include:

• The refrigerator not cooling properly or not cooling at all
• The compressor failing to start, indicated by a clicking sound coming from the back of the refrigerator where the compressor is located.
• The refrigerator or freezer section warming up

This OEM LG part is also compatible with some Kenmore models.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This holder secures the dryer-related assembly in place to reduce movement and wear, helping maintain proper alignment and quieter operation. It's a simple replacement that restores part stability in the appliance. What it does:

• Secures a dryer assembly or component to the appliance frame to prevent shifting
• Helps reduce vibration and rubbing noises caused by a loose part
• Maintains correct alignment so related parts operate smoothly
• Used when the existing holder is cracked, broken, or missing

• Disconnect power before replacing any dryer components to avoid shock or injury
• Access location and removal steps vary by model; follow the appliance's service manual or exploded view
• Keep fasteners and adjacent parts organized for reassembly; replace any damaged clips or screws

This motor bracket is the OEM-style mounting bracket that secures the appliance motor to the cabinet, keeping the motor aligned and reducing vibration for reliable operation. It helps restore proper motor support and stable running. What it does:

• Provides a secure mounting point to hold the motor in correct position
• Maintains motor alignment to prevent belt slip and uneven wear
• Reduces vibration and noise caused by a loose or damaged motor mount
• Can resolve symptoms such as unusual motor noise, excessive vibration, or motor movement during operation

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance service manual for access steps
• Inspect surrounding components (mounting fasteners, motor and belts) and replace any damaged parts

This guide assembly directs and stabilizes the refrigerator/freezer fan to ensure consistent airflow across the evaporator and cooling components. Replacing a damaged guide restores proper air circulation and helps reduce noise from an unsteady fan. What it does

• Holds and centers the fan blade to maintain efficient airflow through the evaporator coil
• Prevents fan wobble or contact with housing that can cause noise or mechanical wear
• Helps ensure even cooling and can reduce frost build-up caused by disrupted airflow
• Supports proper airflow that contributes to consistent temperatures in the cooling compartment

• One guide assembly

• Disconnect power before beginning any repair and follow the appliance manufacturer's safety instructions
• Access may require removing interior panels or the evaporator/fan housing; retain fasteners for reassembly
• Inspect adjacent components while replacing the guide to ensure full repair
• Use only compatible parts and avoid forcing plastic tabs; if clips or screws are damaged, replace them

This fan assembly circulates air through the appliance so coils and internal components operate at the proper temperature. Replacing a failed or noisy fan can restore airflow and help prevent performance issues caused by weak circulation.

• Moves air across coils and components to support designed cooling/dehumidifying performance
• Helps maintain steady airflow to reduce overheating or icing conditions
• A failing fan can cause little to no airflow even when the unit is running
• Common symptoms: fan not spinning, intermittent operation, loud rattling/grinding, vibration, or thermal shutdown

• Disconnect power before servicing to avoid electrical shock or injury
• Access the fan area per your unit's service information; remove panels/shrouds as needed
• Note wire connections and mounting order; transfer any brackets, grommets, or hardware from the old assembly
• After installation, ensure the fan spins freely and clears all shrouds, then test operation before reassembly

The Defrost Sensor Assembly is an OEM part for LG refrigerators. It plays a critical role in the defrost system by monitoring the temperature of the evaporator coil to ensure that it remains at the optimal temperature to prevent frost buildup. The sensor sends signals to the control board, triggering the defrost cycle when necessary.

Over time, the defrost sensor assembly can fail due to wear and tear, electrical issues, or exposure to moisture and temperature fluctuations. When the defrost sensor malfunctions, it can cause improper defrost cycles, leading to excessive frost buildup, reduced cooling efficiency, or the refrigerator not defrosting at all.

Symptoms of a bad defrost sensor assembly include:

• Excessive frost buildup on the evaporator coils
• Refrigerator or freezer not maintaining the correct temperature
• Increased energy consumption
• Refrigerator not defrosting properly

This OEM LG part is also compatible with Sears/Kenmore.

Door switch magnet for reed switch

The Fan Motor is an OEM part for LG refrigerators. It is essential for circulating air throughout the refrigerator and freezer compartments, ensuring that the temperature is evenly distributed and maintained at the set levels. This motor powers the fan that helps to cool the evaporator coils and dissipate heat, which is vital for the appliance's cooling efficiency.

Symptoms of a failing Fan Motor include:

• The refrigerator not cooling adequately
• Unusual noises coming from the refrigerator, such as humming or buzzing
• Ice buildup in the freezer compartment due to poor air circulation
• The refrigerator cycling on and off more frequently

Causes of a bad fan motor can include wear and tear over time, obstructions in the fan blades, or electrical issues such as faulty wiring or a malfunctioning capacitor.

This OEM LG part is also compatible with Sears/Kenmore.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

The Refrigerator Door Switch is an OEM part for LG refrigerators, designed to signal the control system when the door is open or closed. This small but essential component plays a critical role in the overall operation of your refrigerator, including the activation of interior lights and the control of cooling functions. 

Over time, the door switch can fail due to mechanical wear, accidental damage, or a buildup of debris that may prevent it from functioning correctly. 

Symptoms of a bad Refrigerator Door Switch include:

• Interior lights not turning on or off appropriately with the door's position
• The refrigerator running longer than necessary, potentially leading to increased energy bills
• Unusual fluctuations in temperature inside the fridge, affecting food preservation

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Compressor Run Capacitor is an OEM part for LG refrigerators. It plays a critical role in the operation of the refrigerator's compressor by providing the necessary electrical boost to start and maintain the compressor's operation.

Causes of a bad compressor run capacitor can include electrical surges, overheating, or simply wear and tear over time. When the capacitor fails, it can no longer deliver the required electrical charge, which impacts the compressor's ability to start and run efficiently.

Symptoms of a bad compressor run capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual humming or clicking noises from the compressor area
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

This power cord assembly supplies AC power from the wall outlet to your appliance. Replacing a frayed, heat-damaged, or loose cord restores safe, reliable operation and can eliminate intermittent power loss.

• Carries line voltage and ground into the unit to power controls and components
• Routes electricity safely into the cabinet to protect internal wiring
• Replace at the first sign of damage to reduce shock or fire risk

• Disconnect power at the outlet/breaker before servicing
• Compare the new cord to the original; transfer any clips or grommets from the old cord if needed
• Route and secure the cord exactly as original; keep clear of sharp edges and moving parts
• Ensure all connections are fully seated and the ground is properly secured before restoring power

The Compressor Overload Protector Assembly is an OEM part for LG refrigerators. The compressor overload protector steps in if the compressor motor draws excessive current. It then interrupts the power to prevent overheating. The wire harness boosts the compressor to kick-start it, disengaging as soon as the motor reaches the desired speed.

Over time, the compressor overload protector can wear out or become damaged due to electrical issues, power surges, or constant exposure to high temperatures. A faulty protector can compromise the safety and efficiency of the refrigerator’s cooling system.

Symptoms of a bad compressor overload protector assembly include:

• The refrigerator not cooling properly
• The compressor frequently cycling on and off
• Clicking noises coming from the compressor area
• The refrigerator not turning on at all

This OEM LG part is also compatible with Sears/Kenmore models.

This cover assembly protects the appliance's printed circuit board from debris, moisture and accidental contact, helping preserve reliable control operation. It provides a secure enclosure that keeps the PCB mounted and shielded during normal use. What it does:

• Shields the control board from dust, moisture splash and foreign objects that can cause shorts or component damage.
• Keeps wiring and connectors routed and secured to reduce strain and intermittent connections.
• Helps maintain correct spacing and alignment of the PCB for reliable electrical contacts.
• Useful when the original plastic cover is cracked, warped, missing or allows board exposure.

• One cover assembly for PCB.

• Disconnect power to the appliance before beginning any service to avoid shock or damage.
• Handle the PCB and connectors carefully; avoid touching board components or bending traces.
• Align cover over the PCB and fasten with the original screws or clips; do not overtighten plastic fasteners.

The Ice Maker Assembly Kit is an OEM part for LG refrigerators. This kit includes all the components necessary to produce ice efficiently, ensuring a steady supply of ice cubes for your household needs. This particular 12-cube ice maker assembly features a 10-wire harness. 

Causes of a bad ice maker assembly can include wear and tear over time, issues with the water supply, or mechanical malfunctions that prevent the ice maker from operating correctly. These issues can lead to a reduction in ice production or complete failure of the ice maker.

Symptoms of a bad ice maker assembly include:

• No ice production
• Ice cubes being smaller than usual
• Leaks around the ice maker area
• Unusual noises during the ice-making process

This OEM LG part is also compatible with Sears/Kenmore.

The Gasket, Foam is an OEM part for LG refrigerators. This foam gasket creates an essential seal around the refrigerator door, helping to maintain cool interior temperatures and block warm air from entering. It also assists in preventing moisture exchange, keeping contents dry. 

Symptoms of a damaged gasket include:

• Warm or unpleasant air feeling around the edges of the door 
• Higher energy costs from poor insulation
• Extra frost or moisture buildup inside
• Visible air gaps when the door is closed

Causes may be general wear and breakdown over time due to repeated opening and closing of the door. Replace this LG OEM foam gasket to restore an efficient seal and optimal refrigerator performance. This gasket is compatible with models produced by Kenmore, Sears, Samsung, Electrolux, and GE as well.

The Inlet Water Valve Assembly is an OEM part for LG refrigerators, designed to manage the flow of water into the refrigerator's ice maker and water dispenser. This part ensures that your refrigerator provides clean, fresh water and ice on demand by controlling the water pressure and flow through the system. The valve assembly is key to maintaining the refrigerator's functionality and the freshness of the water and ice it dispenses.

Causes of a bad Valve Assembly, Water can include mineral build-up from hard water, which can block the valve and prevent it from opening or closing properly. 

Symptoms of a bad Valve Assembly include:

• No water dispensed
• Leaking water from the refrigerator
• Ice maker not producing ice
• Strange noises coming from the refrigerator when the dispenser is used

This OEM LG part is also compatible with some Kenmore models.

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

The Temperature Sensor is an OEM part for LG refrigerators. It monitors the internal temperature and sends this information to the control board, ensuring that the refrigerator maintains the correct temperature for optimal food preservation.

Over time, temperature sensors can fail due to electrical issues, exposure to moisture, or wear and tear from continuous use. 

Symptoms of a bad temperature sensor include:

• Inaccurate temperature readings
• The refrigerator or freezer being too warm or too cold
• The refrigerator running constantly or not running at all
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances.