Parts for Frigidaire FGMO226NUDA: Oven,Cabinet Parts

This cover is a protective trim piece that shields and neatly finishes exposed components on your appliance. Replacing a cracked or missing cover restores protection and a clean, factory look while helping prevent accidental contact with internal parts.

• Conceals and protects wiring, mechanisms, or mounting hardware from dust and incidental contact
• Restores proper fit and finish for a clean appearance
• Helps ensure components remain secured and unobstructed
• Common symptoms include cracks, broken tabs, discoloration, or a missing/loose cover

• Disconnect power before servicing; shut off water supply if working near water lines
• Retain and reuse original screws or clips; transfer any clips from the old part if applicable
• Align tabs/slots and secure without overtightening to avoid damage
• The cover sits flush and doesn't interfere with doors, drawers, or moving parts

Replacement refrigerator thermostat that controls compressor on/off cycles to maintain the set cabinet temperature. Installs behind the control knob to restore consistent temperature regulation when the original thermostat fails. What it does:

• Regulates compressor cycling to keep the refrigerator at the selected temperature.
• Commonly needed when the fridge runs constantly, won't reach set temperature, or cycles on and off rapidly.
• Mounts into the control housing and connects to the existing wiring harness for direct replacement.
• Works with the appliance's built-in temperature control to stabilize interior temperatures.

• Disconnect power to the appliance before attempting any repair.
• Access the control housing by removing the control knob and trim; retain all mounting hardware.
• Match terminal locations and wiring before removing the old thermostat; install in the same orientation and secure firmly.

This adjustable leveling foot raises and stabilizes the appliance for proper alignment and even weight distribution. It restores a steady, wobble-free base so doors close correctly and the appliance sits level on uneven floors. What it does:

• Replaces a worn or damaged cabinet/console leveling foot to restore stable support
• Allows height adjustment to correct leaning or rocking on uneven surfaces
• Helps ensure doors and drawers close smoothly by keeping the appliance level
• Fits under the appliance base where a threaded/adjustable foot is required

• One adjustable leveling foot

• Turn the appliance off/unplug and empty lower compartments before accessing the foot
• Raise or support the appliance safely following manufacturer guidance before removal/installation
• Thread the foot into the mounting socket until it contacts the floor, then fine-tune the height for level

This control panel is the user interface console that houses the touchpads and display for oven/range functions, restoring reliable control and visible status for cooking cycles and settings. What it does:

• Provides the buttons/touchpads and display used to set bake, broil, timer, clock, and other oven functions
• Relays user commands to the range's electronic control board so selected cycles start and stop
• Shows oven status, temperature readouts, and error messages via the display
• Common replacement when buttons stop responding, display is dim or unreadable, or the console is cracked

• One control panel (user interface console) assembly

• Disconnect power at the breaker before servicing to avoid shock; verify power is off.
• Some installations require removing trim and disconnecting wire harnesses—handle display and connectors carefully.
• Do not attempt repair with live power connected.

This electronic control panel is the front user interface that lets you set and monitor oven functions, temperature and timers for your range or wall oven. It restores button control and display feedback so the appliance responds correctly to settings. What it does:

• Replaces a cracked, burnt or non-responsive control panel to restore user input and display functions
• Returns control over bake, broil, timer and clock settings when buttons or touchpads fail
• Fixes symptoms such as unresponsive keys, blank or flickering display, or intermittent control behavior
• Works as the main interface between the user and the oven's electronic control

• One control panel user interface assembly

• Disconnect electrical power to the appliance at the breaker before starting
• Handle display and fascia carefully to avoid scratching or cracking glass/plastics
• Basic tools are typically required; alignment and connector seating must be checked during reassembly

This control panel is the front console fascia for your range/oven that houses the user controls and display, restoring the unit's appearance and providing the mounting surface for buttons and indicators. What it does:

• Provides the front mounting surface for the control buttons, touchpad or knobs and display window
• Protects underlying electronics and wiring from spills and debris
• Restores a broken, cracked or cosmetically damaged console to normal use
• Re-establishes firm button/knob alignment and reliable access to oven/range functions

• Disconnect power to the appliance at the breaker before starting work
• Use basic hand tools; avoid sharp force on the display window or plastic clips
• Handle the panel carefully to prevent scratching or cracking during installation

The Door Assembly is an OEM part for Frigidaire microwave ovens. Securing the front of the microwave cavity, the door assembly consists of an outer metal casing enclosing a perimeter gasket and interlocking latch mechanism. This assembly allows for the opening, closing, and sealing of the microwave.

Causes of a bad door assembly include cracked or misshapen door exteriors, ruptured perimeter gaskets no longer creating a proper seal, or failed latching systems unable to securely lock the door shut. 

Symptoms of a bad Microwave Door Assembly include:

• Leaks of electromagnetic radiation from door perimeter  
• Door failing to latch or release properly
• Gasket failing to form an airtight bond around waveguide
• Physical deformation preventing a flush door closure

This genuine OEM part is compatible with Electrolux, Gibson, and some Kenmore microwave models as well.

The Magnetron is an OEM part for Frigidaire microwave ovens. Located behind the waveguide plate inside the microwave chamber, the magnetron generates electromagnetic waves to cook and heat food. Powered by a high-voltage transformer, a magnetron coil focuses 2.45GHz radio waves through the waveguide into the cavity.

Causes of a bad magnetron can include failures of the cathode filament or insulator over extended use, depletion of filament or high voltage components.

Symptoms of a bad Magnetron include:

• Slow or incomplete cooking even on high power 
• Discolored or burnt spots on food
• No visible arcing yet cavity runs continuously
• Oversparking sounds or burning smells from chamber

This genuine OEM Frigidaire magnetron is compatible with Electrolux, Gibson and some Kenmore microwave models as well.

This transformer converts incoming power to the low-voltage control circuit used by the appliance, providing a stable source for door controls and other low-voltage components. Replaces a worn or failed control transformer to restore proper low-voltage operation. What it does:

• Steps down line voltage to the appliance's low-voltage control circuit
• Powers door controls, relays, timers, and other low-voltage components
• Can prevent intermittent control failures, dim or non-working displays, and non-responsive door functions
• Fits in the control area and connects to existing wiring harnesses

• One replacement transformer

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle with care; confirm wiring colors and terminal locations before disconnecting
• Secure mounting and proper grounding are required for safe operation

Replacement electrical diode for Frigidaire refrigerators that directs current flow to protect control circuitry and help defrost and compressor systems operate correctly. Installs quickly to restore proper electrical function when a diode fails. What it does:

• Allows electrical current to flow in only one direction to protect sensitive control and compressor circuits.
• Prevents backfeed that can damage control boards or other components.
• Common symptom: intermittent or no compressor/defrost operation.
• Other symptoms: blown fuses, tripped breakers, or erratic electrical behavior in the appliance.

• Disconnect power to the appliance before beginning any service.
• Handle electrical connections carefully; use insulated tools and avoid touching live terminals.
• Confirm connector fit and orientation before finalizing installation.

This replacement refrigerator water filter cartridge helps restore clean tasting water and ice by trapping common impurities. Designed as a direct-fit replacement to maintain your fridge's filtered water supply and improve taste clarity. What it does:

• Filters particulates and common contaminants to improve water and ice taste
• Helps reduce visible sediment and cloudiness from the dispenser and ice maker
• Restores normal dispensing performance when an old filter causes off-flavors or odors
• Supports consistent filtered water flow when installed and maintained

• Turn off the water supply and follow the refrigerator's filter-replacement instructions before starting
• Push/rotate or slide per your model's procedure until the filter locks in place; ensure a secure seal
• Run water through the dispenser for a short time after installation to flush air and initial carbon fines
• Replace regularly per the refrigerator manufacturer's recommendation or sooner if flow decreases or taste returns

This Fuse is an OEM part for Frigidaire microwaves. It's a critical safety component designed to protect the microwave from electrical overload by breaking the circuit if the current is too high. This fuse is specifically tailored to fit and function properly with Frigidaire microwave models, ensuring safety and reliability.

Fuses in microwaves can blow due to power surges, electrical faults within the appliance, or overheating caused by restricted airflow or malfunctioning components. A blown fuse prevents the microwave from operating as a safeguard against potential electrical damage or fire hazards.

Symptoms of a blown fuse include:

• The microwave suddenly stops working and doesn't turn on.
• No response from the microwave's control panel or display.
• The microwave is completely unresponsive, even when the door is opened or closed.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Restore clear visibility inside your appliance with this lamp assembly. Replacing a failed or damaged light module helps you see contents and monitor cycles at a glance, improving everyday use and safety.

• Provides interior illumination so you can view food, items, and appliance status
• Replaces a burned-out, flickering, or intermittent light module
• Addresses damage to the lamp housing, socket, or lens that prevents proper lighting
• Helps resolve cases where the interior light will not turn on or stays dim

• Disconnect power to the appliance before servicing; allow hot surfaces to cool
• Wear cut-resistant gloves; handle any glass components carefully
• Note wire placement and orientation before removal; transfer connectors one at a time
• Do not overtighten fasteners; restore power and test light operation after installation

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

This thermostat replaces the refrigerator's temperature control to help maintain steady food temperatures and reduce spoilage. Use it to restore normal compressor cycling and more consistent cooling performance. What it does:

• Regulates the refrigerator's cooling by sensing temperature and signaling the compressor/fans.
• Helps prevent temperature swings that can cause food to freeze or spoil.
• Common symptom fix: appliance runs continuously, cycles too frequently, or interior is too warm.
• Works as the control point for user temperature settings.

• Disconnect power before accessing or replacing the thermostat to avoid shock.
• Handle wiring and terminals carefully; note wire locations before removal.
• Replacement typically requires removing interior panels or control housing and basic hand tools.

This bracket secures a component or panel within the appliance to keep it aligned and stable during operation. Replacing a cracked or missing bracket restores proper support and helps prevent vibration, rattling, or shifting.

• Provides a rigid mounting point for the original component or panel
• Maintains alignment so assemblies operate smoothly
• Replaces broken, warped, or missing hardware that causes looseness or noise
• Helps reduce vibration and rattling during use

• Disconnect power before servicing; shut off gas/water if applicable
• Note the original orientation and fastener locations; transfer any clips or spacers from the old bracket
• Reuse existing screws unless damaged; tighten evenly without overtightening
• Verify alignment and operation before reinstalling covers or panels

This replacement lever is the small actuator that engages control linkages so doors, latches or dispenser mechanisms move and stay in position. Replacing a worn or broken lever restores reliable mechanical operation and alignment. What it does:

• Transfers motion from a handle or control cam to the linked mechanism
• Helps door/latch/dispenser engage and stay in the correct position
• A damaged or cracked lever can cause sticking, poor latching, or intermittent operation
• Commonly fails from wear, impact, or plastic fatigue

• Disconnect power to the appliance before beginning work to avoid injury
• Removal typically requires basic hand tools; keep fasteners for reuse
• Handle small plastic parts carefully to avoid damage during installation
• Test the mechanism through a full cycle after installation to ensure proper engagement

This replacement switch opens and closes an electrical circuit to control or sense a function in your appliance. It restores reliable start/stop or detection when the original switch wears out, sticks, or fails electrically.

• Controls power or sends a signal when actuated by a button, lever, cam, or door mechanism
• Helps ensure components start/stop only when intended
• Common symptoms: no response when pressing/closing, intermittent operation, appliance won't start due to a safety switch not closing, light/dispenser stuck on or off
• Visual clues may include heat damage at terminals or a broken/sticky actuator

• Disconnect power before servicing; shut off gas/water if applicable
• Note wire positions and take a photo; transfer wires one at a time to the new switch
• Check continuity with a multimeter; the switch should change state when actuated

The Switch is an OEM part for Frigidaire microwaves. It is responsible for detecting whether the microwave door is closed or open. The door switch ensures that the microwave oven operates only when the door is securely closed for safety.

A bad door switch can be caused by wear and tear over time, physical damage, or electrical issues. Signs of a faulty switch include the microwave not starting or operating when the door is closed, or the microwave continuing to operate even when the door is open.

Symptoms of a bad door switch include:

• The microwave not starting 
• The microwave running when the door is open

Replace your malfunctioning or damaged microwave door switch with this genuine OEM Frigidaire part to restore your microwave oven. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement switch restores reliable on/off control to the circuit it serves. When the original wears out or overheats, installing a new switch can resolve non-responsive controls and intermittent operation so your appliance functions as intended.

• Opens and closes an electrical circuit when actuated by the appliance's lever, button, or mechanism
• A failed switch can cause no response, intermittent operation, or components that won't turn off
• Common signs include a stuck/loose actuator or burned/broken terminals
• Continuity testing with a multimeter can switch failure

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Note/photograph wire locations and transfer one lead at a time to matching terminals
• Use needle-nose pliers to remove spade connectors—do not pull on the wires
• Verify continuity and test operation before reassembly

This electric fan motor powers airflow inside the appliance to keep components cool and maintain proper temperature. Replacing a worn motor restores airflow and helps the appliance reach and hold the correct temperature. What it does:

• Spins the internal fan or blower to circulate air across coils and compartments
• Restores airflow for proper cooling and heat dissipation
• Stops or reduces abnormal noise caused by worn bearings or imbalance
• Helps prevent overheating of components by moving air where needed

• One motor as shown

• Disconnect power before starting any repair to avoid shock or injury
• Handle the motor and wiring harness carefully; match connector orientation when reconnecting
• If mounting hardware, fan blade, or wiring are damaged, replace them to ensure reliable operation

Ring assembly that restores proper alignment and sealing where components meet in compatible Frigidaire appliances, helping stop leaks, reduce vibration, and support reliable operation by replacing worn or damaged rings. What it does:

• Provides a secure seal and proper fit between mating parts to reduce leaks or airflow loss
• Helps eliminate rattling or movement caused by a worn, cracked, or deformed ring
• Restores component alignment so controls and panels seat correctly
• Use when the original ring shows visible wear, cracks, warping, or is missing

• Disconnect power (or unplug) and shut off water/gas where applicable before beginning any repair
• Inspect surrounding parts and mounting surfaces; clean debris before installing the new ring
• Use appropriate hand tools and replace any fasteners that are damaged or corroded

This replacement tray restores a sturdy, level surface inside your appliance. Swap out a cracked or missing tray to keep items supported and organized, prevent tipping or spills, and bring back the intended fit and finish.

• Provides a stable platform for foods, containers, or accessories inside the appliance
• Restores proper fit when the original tray is cracked, warped, stained, or missing
• Helps resolve issues like items rocking, rattling, sliding, or the tray not seating level
• Designed to engage the appliance's existing supports for secure use

• Disconnect power to the appliance before servicing and remove items from the area
• Wear cut-resistant gloves; handle carefully to avoid chips, cracks, or cuts
• Note the original orientation; align and fully seat the new tray on the supports
• Inspect the supporting tabs/rails for bends or damage