Parts for Frigidaire FPMV189KFB: 03 - Oven / Cabinet Parts

Microwave not heating but humming loudly? A failed high-voltage diode is often the cause. This rectifier converts AC to DC for the magnetron circuit.

Fix a microwave that hums loudly but won't heat. This high voltage capacitor works with the magnetron to generate heat. Moderate DIY repair.

Fixes microwave that won't power on or shuts off unexpectedly. This thermal cutout switch prevents overheating by cutting power when temps get too high.

If your microwave runs but doesn't heat food, the magnetron likely failed. This part generates the microwave energy. Moderate DIY repair, 1-2 hours.

Microwave runs but won't heat, or stays on when door opens? A faulty door switch is the likely cause. DIY repair takes about 30 minutes with basic tools.

Microwave won't start, light stays on, or fan runs constantly? A faulty door switch is often the culprit. Test with multimeter to identify the bad switch.

Replacement power cord for your microwave. Connects the appliance to your electrical outlet. Order a new cord if yours is frayed, damaged, or missing.

Replace your microwave's light socket if bulbs fail to illuminate despite having power. Restores interior or under-cabinet lighting. Verify fit by model.

If your microwave turntable won't rotate or makes grinding noises, this motor is the likely fix. Direct drive replacement for common motor failures.

Microwave won't turn on, made popping noise, or smells like burned electrical? The noise filter often fails when solder joints arc or short out.

Microwave not heating or won't start? This thermal cutout fuse protects against overheating. Quick DIY fix—test for continuity with a multimeter.

Restores interior and cooktop lighting in your microwave. Replace when bulb burns out or dims for clear visibility. Verify fit with your model number.

This wiring diagram is the factory service schematic that shows the electrical layout for the appliance, helping technicians and DIYers identify circuits and wire routing for accurate troubleshooting. What it does:

• Shows component locations, wiring connections, and circuit paths in plain schematic form
• Helps diagnose electrical issues like no power to components, shorts, or intermittent operation
• Clarifies connector pinouts and wire colors for safe testing with a multimeter
• Supports correct reassembly after repairs by showing original wiring routes

• One original factory wiring diagram (single printed schematic)

• Read the diagram fully before testing or disconnecting wiring; follow all safety procedures
• Always disconnect power before accessing electrical components or performing tests
• Use the diagram alongside an electrical meter for safe diagnostics

Black cooktop assembly cover panel for microwaves. Replaces cracked, broken, or missing trim pieces. Restores the finished appearance of your unit.

Black cooktop cover for your microwave. Replaces cracked, broken, or missing covers. Restores the appearance of your appliance's cooktop area.

Glass cover for microwave hood lamp. Protects the light bulb from grease and debris. Replace if cracked, broken, or missing to restore proper lighting.

Mounting bracket for microwave installation. Secures microwave to wall or cabinet. Replace if bent, cracked, or missing for proper support and stability.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Controls airflow in your microwave's exhaust vent system. Installs between blower and duct. Replace if cracked, broken, sticking, or missing.

Replacement glass turntable tray for your microwave. Installs on the rotating support to hold food during cooking. Replace if cracked, chipped, or broken.

Secures microwave components to cabinet or frame. Replace when bracket is broken, cracked, or worn causing misalignment or excess vibration during operation.

Replace your worn or missing microwave door bushing. This small plastic component helps the door hinge operate smoothly and maintain proper alignment.

Secures your microwave door to engage the safety switches. Replace if the hook is cracked, broken, or worn, preventing the door from latching properly.

Microwave overheating or not venting properly? A worn blower wheel restricts airflow. This fan blade restores cooling and exhaust ventilation.

Microwave duct that directs airflow from the cavity to the exterior vent. Replace if cracked, damaged, or missing for proper ventilation performance.

This clear light lens covers and protects the interior lamp, directing and diffusing light inside the appliance for better visibility. It replaces a cracked, yellowed, or missing lens to restore even interior illumination. What it does:

• Protects the interior lamp from spills, steam, and physical contact
• Diffuses and directs light for more even illumination inside the compartment
• Restores visibility when the original lens is cracked, cloudy, or missing
• Helps prevent direct contact with the bulb for safer operation

• Disconnect power to the appliance before starting any work
• Allow the bulb to cool completely before removing the old lens
• Handle the lens gently to avoid cracking; align tabs or clips and snap into place
• If the lens uses screws, tighten securely but do not overtighten to avoid cracking

Replacement mounting bracket for microwave installations. This support bracket secures the unit to cabinetry or walls. Needed when original is cracked or bent.

A small rubber cushion that cushions and isolates moving parts to reduce noise, vibration, and wear. Fits where a soft bumper or spacer is required to protect surfaces and keep components aligned. What it does:

• Absorbs shock and reduces rattling between parts
• Prevents metal-to-metal contact that can cause noise or wear
• Keeps panels, doors, or assemblies properly spaced and aligned
• Helps stabilize components during operation

• One rubber cushion/buffer

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Inspect the mounting area and clean debris before installing the cushion
• Press or snap the cushion into place; if fasteners are required, use the OEM-specified screws or clips

This small rubber cushion cushions contact points to reduce vibration and prevent metal-on-metal noise or surface wear. It restores quiet, stabilizes moving parts, and helps maintain proper alignment for smooth operation. What it does:

• Acts as a soft bumper between components to absorb shock and reduce rattling.
• Prevents direct contact that can cause scratches, chipping, or wear.
• Helps maintain proper spacing and alignment of panels or assemblies.
• Commonly replaced when torn, flattened, hardened, or missing.

• Designed for a simple swap; remove the old cushion and press the new cushion into place.
• Inspect the mounting surface for debris or damage before installing.
• Use basic hand tools only; disconnect power/unplug appliance if servicing near electrical connections.
• If adhesive is present, allow any adhesive to set according to the adhesive manufacturer's instructions.

This is a replacement adhesive identification label used to restore factory markings and safety information on the appliance. It helps keep model, rating or warning information legible for service and safe operation. What it does

• Replaces a torn, faded, or missing appliance identification label
• Restores readable model, serial, rating or warning information that owners rely on
• Helps prevent confusion during service by keeping factory markings visible
• Maintains appliance appearance and compliance with original labeling

• One adhesive identification label

• Clean and dry the application area before installing to ensure proper adhesion
• Align the label carefully and press firmly from one side to the other to avoid bubbles
• No specialized tools required; avoid stretching or folding the label during placement

This replacement identification label displays appliance model, serial, and rating information so you can correctly identify your unit for service or parts ordering. Durable adhesive backing helps keep factory information legible. What it does:

• Replaces a torn, faded, or missing identification/rating label so model and electrical data are readable
• Helps technicians and owners model/serial and voltage/current ratings during diagnosis or repairs
• Prevents confusion when ordering parts or scheduling service by restoring original identification
• Non-electrical — does not affect operation of the appliance

• Clean and dry the mounting surface before applying for best adhesion
• Peel backing and press firmly; avoid stretching or folding the label
• Do not place over vents, seals, or moving parts; install in the original label location if known

Traps grease and smoke from cooking. Replace when clogged or damaged to maintain ventilation efficiency. Verify compatibility with your model number.

Secures panels and components inside your microwave, keeping parts aligned and reducing rattles. Replace when clip is broken, cracked, or missing.

Replacement mounting screw for microwave ovens. Secures internal components and panels. Needed when original screws are stripped, missing, or damaged.

Mounting screw for microwave and wall oven assemblies. Replace if lost, stripped, or damaged during installation or service. Secures components.

Replacement mounting screw that secures panels, trim, and internal components in microwaves and wall ovens. Needed when screws are stripped, missing, or lost.

Screw secures the door latch and upper hinge plate on your microwave. Replace if missing, stripped, or loose to properly fasten door hinges and latch.