Kenmore Washer 110.10852991 (11010852991, 110 10852991) Parts

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

For end of drain hose.

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings

This agitator cap is the top cover for the washer agitator/auger assembly, keeping the agitator hardware protected and holding the auger components in place. It restores a finished appearance and ensures the agitator operates without interference. What it does:

• Covers and protects the agitator bolt and internal auger components from debris and fabric
• Helps keep the agitator secure and centered during wash cycles
• Can reduce rubbing or noise caused by a cracked, loose, or missing cap
• Supports proper fit of the agitator assembly for smooth agitation

• One agitator cap assembly

• Disconnect power to the washer before starting any repair
• Remove the agitator per the OEM instructions to access and replace the cap
• Inspect surrounding components (bolt, washer) and replace any worn parts as needed
• Use proper tools and wear gloves to avoid cuts from sharp edges

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This drain hose coupling kit connects the washer drain hose to the appliance drain outlet, restoring a secure, leak-resistant hose connection and preventing water leaks during drain cycles. What it does:

• Provides a replacement coupling to join the drain hose to the washer drain outlet
• Re-establishes a tight hose connection to reduce leaks and water damage
• Addresses symptoms such as leaking at the drain connection or a loose hose fit
• Compatible with affected Whirlpool top-load washer drain assemblies

• Unplug the appliance before servicing and work on a dry surface
• Remove the old coupling and inspect the hose and outlet for damage before installing
• Ensure the hose is fully seated and secure with the existing or supplied clamp(s)

Motor mount to gear case.

This balance ring mounts on the top of the washer's spin basket. Its sealed, liquid-filled chamber shifts weight to counterbalance uneven loads so the tub spins smoothly, reducing vibration, noise, and stress on other components. What it does:

• Uses internal fluid to counterbalance heavy or uneven loads during spin
• Helps minimize vibration, shaking, and thumping noises
• Reduces washer movement or "walking" during spin
• Common failure symptoms: excessive vibration/noise, frequent out-of-balance loads, or visible cracks/leaks at the ring

• 1 balance ring assembly

• Disconnect power and water; wear gloves and use proper safety precautions
• Access the ring by removing the cabinet/top and inner basket (procedure varies by model)
• Remove the old ring; seat the new ring evenly on the basket rim—do not puncture the sealed chamber
• Reassemble, level the washer, and run a test spin to ensure smooth operation

This gull-wing upper agitator replaces a damaged or worn top-load washer agitator to restore proper fabric movement and cleaning action. It fits select Whirlpool-design washers and connects to the agitator spline for secure operation. What it does:

• Moves clothes through the wash water to improve soil removal and rinsing
• Restores normal agitation when the original agitator is cracked, stripped, or missing
• Works with the washer's transmission and agitator coupler to transfer torque
• Helps maintain balanced load movement to reduce excessive vibration

• One gull-wing upper agitator

• Remove power and water supply before beginning any repair
• Typically installs onto the agitator spline and secures per the model's service instructions
• Inspect the agitator coupler/spline for wear; replace if stripped to ensure a lasting repair

This motor shield protects and secures the appliance motor assembly, helping block debris and contact with nearby components so the motor can run reliably. It's a direct-fit replacement for a damaged or missing motor shield. What it does

• Shields the motor from debris and foreign objects that can cause rubbing or obstruction.
• Helps secure and position the motor within the cabinet to maintain proper alignment.
• Reduces risk of contact between the motor and other parts that can cause noise or wear.
• Replacing a cracked or missing shield can prevent recurring motor issues and reduce abnormal sounds.

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools; avoid forcing fasteners or damaging adjacent components.
• Wear gloves to protect against sharp edges on the shield or mounting area.

Rear panel pad cushions and insulates the appliance's rear cabinet to reduce vibration, noise and rubbing against the back panel. Replacing a damaged pad helps stop rattles and protects internal components from wear. What it does:

• Provides rear-cabinet cushioning and thermal/abrasion protection for the back panel.
• Dampens vibration and reduces operational noise.
• Prevents direct metal-to-metal contact that can cause rubbing or wear.
• Common symptom fix: reduces rattling or vibrating noises from the appliance rear.

• Always disconnect power (and gas, if applicable) before starting any repair.
• Remove the rear access panel to access the pad; replace using the original mounting points, adhesive or clips.
• Inspect surrounding insulation and mounting hardware; replace any damaged fasteners.

This miscellaneous parts kit provides a selection of small hardware and replacement pieces used in appliance repairs, so you have the fasteners and clips commonly needed to secure panels and components during service. What it does:

• Supplies assorted fasteners, clips, and small hardware used across multiple repair steps
• Replaces missing or damaged mounting hardware that can cause loose panels or rattling
• Helps complete repairs without waiting for individual screw or clip orders
• Useful for routine maintenance and reassembly after component replacement

• One miscellaneous parts kit (assorted small hardware)

• Use only the pieces that match the original hardware and fit securely; do not force fasteners
• Power off and disconnect the appliance before beginning any repair
• Keep small parts away from children and pets; handle sharp edges carefully
• If a specific OEM fastener or clip is required, verify fit with the appliance's parts diagram

For mating plug use 691707.