Kenmore Washer 110.14852300 (11014852300, 110 14852300) Parts

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This wire retaining ring secures the door boot (bellow) to the front tub on front-load washers. It keeps the gasket seated to maintain a watertight seal, helping prevent leaks when the washer fills, agitates, and spins.

• Secures the door boot/gasket to the outer tub opening
• Maintains a watertight seal during wash and spin cycles
• Helps prevent the boot from slipping off the tub lip
• Common symptoms: water leaking at the front, a loose or detached boot, or a broken/missing ring

• Unplug the washer and shut off water; wear gloves and eye protection—the ring is under spring tension
• Release the outer boot clamp and fold the boot inward to access the inner ring
• Seat the boot evenly on the tub rim, then expand and fit the ring into its groove; verify it's fully seated all the way around
• Reassemble and run a quick test cycle to check for leaks

This knob insert is the small piece that snaps into a control knob. It restores a clean, finished look when the original insert is cracked, discolored, loose, or missing.

• Provides the insert for a control knob to replace a worn or missing piece
• Snaps in for a secure, factory-style fit
• Helps keep dust and debris out of the knob cavity
• Typical symptoms: knob center missing, insert cracked, loose, or discolored

• Disconnect power before servicing the control panel
• If needed, pull the knob straight off the shaft to access the insert
• Gently pry out the old insert; avoid metal tools that can mar the finish
• Align tabs and press the new insert flush until it clicks into place

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Size: 10-16 x 5/8 inch.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Size: 21 inches long. Clamp included.

Includes drive tube spacer, "T" bearing and both shaft seals.

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

2 position. Extra rinse.

Used for the pressure switch.