Kenmore Dryer 110.78092700 (11078092700, 110 78092700) Parts

Color: White.

This gas burner tube replaces a damaged or corroded oven burner tube to restore proper gas flow to the burner assembly. It's a direct-fit replacement that helps re-establish even heating and reliable ignition. What it does:

• Channels gas from the manifold to the oven burner for a steady flame
• Restores consistent burner flame shape and heat distribution
• Helps correct weak or uneven heating caused by a cracked or clogged tube
• Reduces gas leakage risk from damaged tubing when installed correctly

• Designed for direct replacement; refer to your model's service manual for exact removal/installation steps
• Turn off gas supply and power before starting work; verify no gas leaks after installation
• Inspect surrounding components (burner, igniter, orifices) and clean if needed for optimal performance

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This drum baffle restores proper fabric tumbling and gentle movement inside the dryer drum for more even drying and fewer snags. It fits the drum to help lift and separate items during the cycle. What it does:

• Lifts and guides clothes as the drum rotates to promote consistent tumbling
• Reduces fabric bunching and helps improve air exposure for more even drying
• Prevents garments from riding on the drum seam and reduces rubbing/snags
• Can stop or reduce thumping or uneven tumbling when a worn baffle is the cause

• One drum baffle

• Disconnect power before beginning work
• Installation typically requires opening the dryer's front or top panel and rotating/removing the drum—follow your model's service manual
• Keep track of fasteners and note baffle orientation; replace any damaged clips or screws
• Wear gloves and eye protection; watch for sharp edges and pinch points during reassembly

A small replacement retainer clip that secures interior panels and trim to restore proper fit and reduce vibration or rattling. Fits where a molded or snap-in fastener has worn or broken. What it does

• Secures panels, trim pieces, or wiring harnesses so parts sit flush and stable.
• Prevents rattling and vibration caused by loose or missing fasteners.
• Helps keep seals and gaskets aligned by holding adjacent trim in place.
• Common symptom: loose trim, gaps, or intermittent rattling sound during operation.

• The clip shown.

• Disconnect power (unplug appliance or turn off breaker) before servicing.
• Access the clip location by removing the appropriate trim or panel.
• Clip typically snaps into a mounting hole or slot; align and press until it seats securely.
• Use basic hand tools as needed; wear gloves and eye protection to avoid injury from sharp edges.

This bracket is used to attach and is included in the igniter kit. Save money by ordering the igniter kit 279311.

This foam seal cushions and seals the icemaker area to reduce vibration and prevent air leaks that can affect ice quality and efficiency. It's a direct-fit replacement designed to restore proper sealing around the icemaker housing. What it does:

• Cushions the icemaker assembly to reduce noise and movement
• Helps seal gaps to limit warm air intrusion that can cause icemaking issues
• Supports consistent ice production by maintaining the intended airflow path
• Resists compression set for reliable sealing over time

• One foam seal for the icemaker housing

• Basic installation; remove power to the appliance before starting
• Align the seal to the icemaker housing, pressing into place until fully seated
• Inspect surrounding surfaces for debris or damage and clean before installing

The Lint Filter Grille is an OEM part for Whirlpool dryers. This grille covers and secures the lint filter, ensuring it stays in place to effectively trap lint and debris during the drying cycle. The grille measures approximately 21 inches by 7 inches. 

You should replace the lint filter grille if it becomes damaged or worn out. Causes of a bad lint filter grille can include regular wear and tear from frequent use, physical damage from handling, or brittleness due to prolonged exposure to heat.

Symptoms of a bad lint filter grille include:

• The lint filter not staying securely in place
• Excessive lint buildup inside the dryer drum or vent
• Visible cracks or breaks in the grille
• Difficulty inserting or removing the lint filter

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This axial motor assembly drives a cooling fan to move air through the appliance, helping protect internal components from heat. Replacing a worn or noisy unit restores ventilation and reduces heat-related shutdowns or performance issues.

• Circulates air across heat-generating parts to dissipate heat
• Helps maintain stable operating temperature and protect electronics
• Failure signs can include the fan not running, intermittent operation, loud or grinding noise, overheating, or a burning smell
• Inadequate airflow may trigger thermal cutoffs or nuisance shutdowns

• Disconnect power before servicing; allow hot components to cool
• Access the motor location and note wire positions; take photos for reference
• Transfer any brackets or grommets from the old unit if required; keep wiring clear of the fan path
• After mounting, hand-spin the fan to ensure free movement before restoring power and checking airflow