Kenmore Washer Dryer Combo 110.88732792 (11088732792, 110 88732792) Parts

This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.

This replacement cap covers an opening or fastener on the appliance. It helps keep water, detergent, and debris out while restoring a clean, finished look and maintaining a secure fit. What it does:

• Covers and protects an exposed opening or fastener from moisture and debris
• Helps prevent residue from entering internal areas
• Restores the appliance's finished appearance
• Common signs of failure: missing cap, cracks, warping, or a cap that won't stay seated

• 1 cap

• Unplug the appliance; if working near water connections, turn off the water supply
• Carefully remove the old cap without prying against delicate surfaces
• Clean the mating area; align and press or twist the new cap until fully seated
• Verify a secure fit and normal operation

This flat support washer provides a stable bearing surface under a fastener. Its 1-1/2-in diameter helps distribute load, maintain spacing, and keep components aligned so hardware stays tight and assemblies operate smoothly. What it does:

• Distributes clamping force to prevent pull-through and gouging
• Maintains proper spacing and alignment between mating parts
• Helps reduce vibration, rubbing, or wobble from a loose assembly
• Replaces a cracked, deformed, or missing support washer

• One support washer

• Disconnect power and shut off water/gas before servicing.
• Note the order and orientation of any washers/spacers during disassembly.
• Inspect mating hardware and surfaces; replace any worn or damaged parts.
• Tighten fasteners to manufacturer specifications—do not over-tighten.

This mechanical timer controls the sequence and duration of wash, rinse, and spin cycles in your washer. Replacing a worn timer restores consistent cycle advancement and proper power distribution to the motor, pump, and water inlet valves. What it does

• Coordinates and powers components through wash, rinse, and spin in the correct order and timing
• Advances automatically through the selected cycle after you set the knob
• Common symptoms of a failing timer: cycle won't advance or stops mid-cycle; timer knob doesn't move; intermittent agitation or spin

• Timer assembly

• Disconnect power before servicing
• Open the control console; remove the old timer and note its orientation
• Transfer wire connectors to the new timer one at a time to maintain placement, then secure the timer
• Reassemble the console, ensure the shaft engages the knob/dial, restore power, and run a short test cycle

This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:

• Holds the motor firmly in place within the assembly
• Maintains alignment for smooth, quiet operation
• Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
• Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor

• Includes 1 motor retainer.

• Disconnect power; turn off water supply.
• Access the motor area and support the motor before removing the old retainer.
• Inspect mating parts and seals; replace any damaged components.
• Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.

This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.

• Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
• Replaces a lost, worn, or damaged anti-rattle fastener
• Helps maintain proper alignment and prevents vibration-related wear
• Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet

• Disconnect power before servicing; for gas appliances, shut off the gas supply
• Access the mounting point and remove the loose or damaged screw
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the bracket/clip before reassembly

This replacement drive motor powers your appliance's mechanical drive system. A worn or seized motor can cause humming, stalling, or a no-run condition. Installing a new motor restores reliable rotation and full cycle operation.

• Supplies rotational power to the unit's drive mechanism
• Can help fix: won't run/start, hums but won't turn, stalls or stops mid-cycle, trips breaker or overheats
• Helps reduce excessive buzzing or burnt-odor from a failing motor

• Disconnect power at the breaker before servicing; allow hot components to cool
• Access varies by model; photograph wiring and note routing before removal
• Transfer any brackets, pulleys/gears, or mounting hardware from the old motor if required
• After installation, verify the drive turns freely and no components are binding before restoring power

This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

Used for lid switch.

This rear foot assembly supports the back of the appliance and helps keep it level. Replacing a worn or missing foot restores stability, reduces vibration, and helps prevent the unit from rocking or "walking."

• Supports the rear of the cabinet and maintains proper height
• Provides a stable contact point with the floor for accurate leveling
• Helps reduce vibration, rattling, and movement during operation
• Common signs of failure: rocking/wobbling, excessive vibration, noise from the base, or a visibly worn/missing foot

• Disconnect power before servicing; if applicable, shut off water supply
• Protect the floor and carefully tilt or lay the appliance back with assistance
• Remove the old rear foot and install the new assembly per your model's instructions
• Set the unit back in place, level it, and verify stability

This wire retaining ring secures the door boot (bellow) to the front tub on front-load washers. It keeps the gasket seated to maintain a watertight seal, helping prevent leaks when the washer fills, agitates, and spins.

• Secures the door boot/gasket to the outer tub opening
• Maintains a watertight seal during wash and spin cycles
• Helps prevent the boot from slipping off the tub lip
• Common symptoms: water leaking at the front, a loose or detached boot, or a broken/missing ring

• Unplug the washer and shut off water; wear gloves and eye protection—the ring is under spring tension
• Release the outer boot clamp and fold the boot inward to access the inner ring
• Seat the boot evenly on the tub rim, then expand and fit the ring into its groove; verify it's fully seated all the way around
• Reassemble and run a quick test cycle to check for leaks

This heat-resistant fiberglass oven door gasket seals the oven cavity perimeter, helping keep heat inside for consistent temperatures and efficient cooking. Replace a worn, frayed, or flattened seal to restore proper door sealing performance. What it does

• Forms a heat-resistant seal around the oven opening to minimize heat loss
• Helps maintain set temperature and overall cooking performance
• Can help address long preheat times, uneven baking, and hot air leaking around the door
• Replace if the gasket is frayed, brittle, compressed, or falling out of its channel

• Includes: 1 fiberglass door gasket

• Disconnect power and allow the oven to cool completely before service
• Remove the old gasket from its mounting slots or clips; clean the channel of debris
• Install the new gasket without stretching; seat it evenly around the perimeter with ends routed as originally positioned
• Close the door and check for uniform contact all around; adjust seating if needed

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This agitator base is the lower section of the washer's agitator. It couples to the drive shaft to move clothes through water and detergent, restoring proper turnover and wash action when the original base is worn, cracked, or stripped.

• Provides the oscillating motion that circulates laundry and detergent for even cleaning
• Maintains proper connection and alignment with the drive shaft
• Helps reduce tangling by rolling clothes over during the wash
• Typical symptoms include no or weak agitation, clothes not circulating, or a wobbling agitator

• Disconnect power to the washer before servicing
• Remove the fabric softener dispenser and agitator cap; remove the center agitator bolt and lift the agitator off the shaft
• Separate the old lower base from the upper section; install the new base, aligning splines, and seat fully
• Reinstall the bolt, cap, and dispenser; run a quick test cycle to ensure proper agitation

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly