Kenmore Washer Dryer Combo 110.88752792 (11088752792, 110 88752792) Parts

This knob insert is the small piece that snaps into a control knob. It restores a clean, finished look when the original insert is cracked, discolored, loose, or missing.

• Provides the insert for a control knob to replace a worn or missing piece
• Snaps in for a secure, factory-style fit
• Helps keep dust and debris out of the knob cavity
• Typical symptoms: knob center missing, insert cracked, loose, or discolored

• Disconnect power before servicing the control panel
• If needed, pull the knob straight off the shaft to access the insert
• Gently pry out the old insert; avoid metal tools that can mar the finish
• Align tabs and press the new insert flush until it clicks into place

This replacement seal restores a tight barrier between mating parts inside your appliance to prevent leaks and keep the assembly performing as designed. Swapping a worn or brittle seal helps stop drips and protects nearby components. What it does:

• Creates a reliable seal between components or around a shaft to prevent leakage
• Helps maintain proper pressure/flow within the system
• Typical failure signs: cracks, flattening, swelling, brittleness, or leakage/residue at the joint

• 1 seal

• Disconnect power; shut off water supply if applicable
• Allow hot components to cool before servicing
• Access the sealed joint; capture any residual water if working on a wet system
• Clean mating surfaces; seat the new seal evenly. Use only manufacturer-approved lubricant if specified, then reassemble and test for leaks.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This water inlet hose routes water from the inlet valve to the appliance's fill path, keeping delivery controlled and leak-free. Replace a brittle, cracked, or clogged hose to stop leaks and restore reliable filling performance.

• Directs water from the inlet valve to the internal fill system
• Maintains a sealed, kink-resistant path to prevent leaks
• Helps the appliance achieve proper water flow/level during operation
• Common symptoms of a failed hose: visible cracks/bulges, leaking, dampness beneath unit, slow or no fill, fill-related error codes

• Disconnect power and shut off the water supply before servicing
• Place towels or a shallow pan to catch residual water
• Note routing and clamp positions; transfer existing clamps/fittings as designed for your model
• Restore water slowly and check all connections under pressure; run a test fill to verify no leaks

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

This cap fits over the siphon break fitting in a drain system, helping contain splashes and seal the opening so the break can work as intended. Replace a cracked, loose, or missing cap to stop leaks and maintain proper drainage.

• Covers and seals the siphon break body/fitting
• Helps prevent water leakage or spray at the break during drain
• Supports proper anti-siphon/backflow operation of the drain path
• Typical signs include leaking at the break, a cap that won't stay on, or visible cracks

• Disconnect power; shut off water if working near hoses
• Access the siphon break and remove the old/damaged cap
• Clean the mating area; install the new cap and hand-tighten—do not overtighten
• Run a short fill/drain and check for leaks

Size: 10-16 x 5/8 inch.

This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.

• Provides front support and height adjustment to level the unit
• Helps reduce rocking, vibration, and rattling during operation
• Replaces a worn, broken, missing, or stripped front foot
• Helps ensure doors or drawers align and close properly when leveled

• Disconnect power and, if applicable, shut off water/gas before servicing
• Protect flooring; carefully tip or brace the appliance to access the front foot
• Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
• Verify stability, then restore utilities and recheck for level

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

This replacement blower wheel restores proper airflow by moving air through the appliance's blower housing and out the exhaust. A worn or stripped wheel can cause weak ventilation, vibration, and noisy operation.

• Attaches to the motor shaft and spins to move air through the blower housing and ducting
• Maintains steady airflow for efficient appliance performance and ventilation
• Typical failure signs: reduced airflow at the exhaust, rattling/scraping noises, wobble on the shaft, or cracked/missing fins
• Helps resolve vibration from an out-of-balance or damaged wheel

• Disconnect power; turn off gas supply before servicing
• Access the blower housing; remove debris and inspect seals before installation
• Transfer any reusable retainer, nut, clip, or set screw from the old wheel as required by your model
• Seat the wheel fully and secure per your model design (e.g., reverse-thread, retainer, or set screw); verify free rotation and clearance before reassembly

This Heater Housing is the metal enclosure that supports the heating element and thermostats and channels airflow through the heater. Replacing a warped, burned-through, or corroded housing helps restore safe, consistent dryer heat and airflow.

• Holds the heating element securely and isolates it from the cabinet
• Directs air across the element for efficient, even heating
• Provides mounting points for high-limit/cycling thermostats and thermal cut-off
• Helps with symptoms such as weak/no heat, scorching in the heater area, repeated element shorts, or visible damage/rust to the housing

• Disconnect power and pull the dryer forward for access
• Remove the rear panel and exhaust duct to reach the heater assembly
• Note wiring; transfer the heating element and thermostats from the old housing to the new one using existing hardware
• Ensure the element is centered and not touching the housing before reassembly; reconnect and test for proper heat and airflow

Almond. Size: 13 oz. can. Acrylic appliance paint.

This drain hose routes water from the drain pump out of the appliance during the drain cycle. Replacing a worn hose helps the unit empty properly and reduces the risk of leaks or water damage. What it does:

• Carries wastewater from the pump outlet to the household drain path
• Provides a sealed flow path to help prevent leaks and backflow
• Replace if cracked, brittle, swollen, kinked, or internally clogged
• Help resolve symptoms like standing water, slow/no drain, water on the floor, or a "long drain" error

• 1 drain hose

• Unplug the appliance and turn off water supply before service
• Expect residual water; use towels or a shallow pan
• Release and reinstall hose clamps securely; ensure full seating on fittings
• Route to avoid kinks or sharp bends; run a test drain and check for leaks

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

This is the washer's water level pressure switch. It senses the tub's water level and tells the control when to start/stop filling and when to advance the cycle. Replacing a failing switch restores accurate fill levels and reliable cycle progression. What it does:

• Monitors tub water level via air pressure through the attached hose
• Opens/closes the inlet valve circuit to stop or start water fill
• Signals the timer/control to advance to wash, rinse, and spin at the correct level
• Common failure symptoms: overfilling or won't stop filling, won't fill, cycle won't advance, or won't agitate/spin

• 1 water level pressure switch

• Disconnect power and shut off water before servicing
• Lift/remove the control console to access the switch
• Label and transfer wires; move the pressure (air dome) hose to the new switch and ensure a snug, unkinked connection
• Inspect the hose for cracks, kinks, blockages, or water inside; reassemble and run a test fill to operation

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling