Kenmore Washer 110.91564800 (11091564800, 110 91564800) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10086010
This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:
- Holds the motor firmly in place within the assembly
- Maintains alignment for smooth, quiet operation
- Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
- Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor
What's included:
- Includes 1 motor retainer.
Install notes:
- Disconnect power; turn off water supply.
- Access the motor area and support the motor before removing the old retainer.
- Inspect mating parts and seals; replace any damaged components.
- Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.
Do-It-Yourself Stories from Customers like You
Motor drive & mounts Mark H. • Winnemucca , NV • October 10, 2024
A former repair man deleted the grommets from the motor mount plate, the spring fastening the motor to the bracket broke the screw inside the motor and once the motor fell out of place the drive to the the transmission was broken.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.
- Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
- Replaces a lost, worn, or damaged anti-rattle fastener
- Helps maintain proper alignment and prevents vibration-related wear
- Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet
What's included: One anti-rattle screw Installation notes:
- Disconnect power before servicing; for gas appliances, shut off the gas supply
- Access the mounting point and remove the loose or damaged screw
- Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
- Repair or replace the bracket/clip before reassembly
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356311
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Do-It-Yourself Stories from Customers like You
Lid safety switch had been removed and bypassed. Dale M. • Torrance , CA • June 22, 2019
Installed a new safety switch and strike. It was a very simple repair and the video described the necessary steps beautifully.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.
- Provides a protective wear surface between the hinge and cabinet/lid
- Reduces squeaks, creaks, and rattling when opening or closing the lid
- Helps maintain proper lid alignment and smooth movement
- Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid
What's included: 1 hinge pad Installation notes:
- Disconnect power to the washer before servicing
- Support the lid to relieve hinge tension and access the hinge area per your model
- Remove the worn pad and press the new pad fully into the hinge location
- Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.
- Applies tension to prevent rattling and buzzing during use
- Helps keep the mounted piece properly seated and aligned
- Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
- Simple, drop-in replacement where the original clip is used
What's included: 1 anti-rattle clip Install notes:
- Disconnect power to the appliance before servicing
- Note the original clip's orientation; transfer the new clip the same way
- Use needle-nose pliers for placement; avoid over-bending the clip
- The component is secure and clears adjacent parts before reassembly
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356467
This water level pressure switch senses the tub's fill level through an air hose and signals the washer to start or stop filling and advance the cycle. Replacing a faulty switch restores proper fill levels and reliable cycle timing.
- Monitors water level via an internal pressure diaphragm connected to the tub air hose
- Opens/closes contacts to control the inlet valve and inform the timer/control
- Common symptoms: washer overfills or keeps filling, won't fill, incorrect/erratic water levels
- Cycle may stall at fill or rinse when the switch doesn't detect the proper level
What's included: 1 water level switch Install notes:
- Disconnect power and turn off water before servicing
- Access the console; transfer wires to the new switch one at a time to maintain correct positions
- Inspect and firmly seat the pressure hose; ensure the hose and tub air dome are clear and the hose isn't cracked or kinked
- After installation, run a test fill to verify proper shutoff at the selected level
Do-It-Yourself Stories from Customers like You
Wash machine once in a while would stop running Daniel B. • Leesburg , FL • May 13, 2016
I found that turning the water level switch back and forth would activate the machine So I replaced the water level switch and the plastic hose that connected to it.
I purchased a clamp in the purchase, but it was the wrong size! There wasn't a clamp used in the original set up, so I installed the switch and hose without it! It was the video instructions and having the correct parts that made that made this a easy repair!
Thank You
Read more
More
$101.95
- Compare At:
-
$121.32
- You Save:
-
$19.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: 285702
Size: 21 inches long. Clamp included.
Do-It-Yourself Stories from Customers like You
Drain hose too short and home depot fix leaked Sara B. • Liberty Hill , TX • August 21, 2015
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly.
Now we're washing again and no leaks!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: 285558
This replacement upper agitator restores the laundry-moving action in compatible top-load washers so clothes get cleaned and rinsed more evenly. It installs on the transmission/drive coupling to re-enable proper agitation. What it does:
- Moves clothes and water during the wash cycle so detergent and water contact fabrics for better cleaning.
- Replaces a cracked, stripped, worn or missing agitator that can cause poor cleaning or uneven loads.
- Helps stop wobbling, banging or unusual noise caused by a loose or damaged agitator.
- Works with the washer's drive coupling/drive block to transfer motor motion into agitation.
What's included: One upper agitator. Install notes:
- Disconnect power and water before starting any repair.
- Remove the agitator cap or fabric softener dispenser, then unbolt/lift the old agitator from the drive coupling per your model instructions.
- Inspect the drive block/agitator dogs and splines for wear; replace those parts if they are damaged to ensure proper operation.
- After installation, run a short test cycle to confirm secure fit and normal agitation.
Compatibility note: Enter the model number into the OEM parts lookup or the retailer's compatibility tool before ordering.
Do-It-Yourself Stories from Customers like You
The two sections of my agitator kept separating & a new screw wasn't the answer but Ann S. • Washington , DC • April 20, 2017
When the drum finally started to list during washings, I knew I couldn't keep screwing the two parts of the agitator together as a temporary fix anymore so I called a technician who promptly and erroneously told me that the entire unit would need to be replaced. This didn't seem right so I checked online and found APP. I'm very thankful I did. The videos, instructions, and parts made the repair possible. With my uncle's elbow grease (taking the old agitator out was no picnic), we were able to...
Read more
More
$150.33
- Compare At:
-
$178.89
- You Save:
-
$28.56
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$19.50
- Compare At:
-
$23.20
- You Save:
-
$3.70