Kenmore Washer 110.92591400 (11092591400, 110 92591400) Parts

This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.

This cap seal creates a tight barrier between a cap and its mating surface in your appliance. Replacing a worn seal restores a secure, leak-resistant fit and helps maintain proper performance over time.

• Forms a tight seal where the cap seats to prevent leaks and seepage
• Helps maintain intended pressure/flow and keeps contaminants out
• Typical failure signs: drips or moisture around the cap area, loose cap fit, or a flattened/cracked seal
• Age, heat, and detergents/chemicals can harden or deform the seal

• Disconnect power and shut off water before servicing
• Remove the cap and note the seal's orientation
• Clean mating surfaces; seat the new seal fully without twisting
• Reinstall the cap and test operation, checking for a leak-free fit

This internal pump-to-drain hose routes water from the drain pump to the outlet, helping prevent leaks and ensuring proper draining. Replace a cracked or clogged hose to restore reliable, mess-free operation.

• Connects the pump outlet to the machine's drain/outlet port to carry wastewater out during the drain cycle
• Maintains a sealed path to help prevent internal leaks
• Common symptoms of failure: water on the floor, slow or incomplete draining, visible splits or soft spots on the hose
• Replacing a restricted hose can reduce drain pump strain and noise

• Disconnect power and shut off water supply; remove standing water from the tub if needed
• Access the drain pump and hose by removing the cabinet/front or rear panel per your model
• Release hose clamps, remove the old hose, and seat the new hose fully on both fittings; reuse clamps if in good condition
• Route the hose as originally to avoid kinks; run a drain cycle and check for leaks

This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:

• Holds the motor firmly in place within the assembly
• Maintains alignment for smooth, quiet operation
• Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
• Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor

• Includes 1 motor retainer.

• Disconnect power; turn off water supply.
• Access the motor area and support the motor before removing the old retainer.
• Inspect mating parts and seals; replace any damaged components.
• Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.

Hose used from mixing valve to sensor housing.

This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.

• Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
• Replaces a lost, worn, or damaged anti-rattle fastener
• Helps maintain proper alignment and prevents vibration-related wear
• Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet

• Disconnect power before servicing; for gas appliances, shut off the gas supply
• Access the mounting point and remove the loose or damaged screw
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the bracket/clip before reassembly

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.

This Agitator Auger is the upper half of a dual-action washer agitator. It works with the agitator cam and dogs to create the screw-like motion that pulls clothes downward; replace if the top agitator slips, cracks, or stops turning.

• Forms the upper agitator that produces the ratcheting, spiral action for proper wash turnover
• Common symptoms include the upper agitator not moving, free-spinning or slipping under load, and visible cracks or stripped splines/fins
• Restores correct clothing movement and agitation performance when the upper section no longer drives

• Disconnect power and water before servicing
• Remove the fabric softener dispenser and inner cap, then unbolt and lift off the agitator to access the auger
• Transfer internal components (cam and agitator dogs) if reusing; inspect for wear during reassembly
• Align splines, seat the auger fully, tighten fasteners securely, and test the agitation function

Push-in.

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This washer agitator is the central wash-motion component. It mounts to the drive hub and churns laundry through water and detergent, restoring proper turnover when the original agitator is cracked, stripped, or missing.

• Creates the back-and-forth wash action that moves clothes through the wash water
• Restores proper turnover and cleaning when the old agitator is damaged or worn
• Typical symptoms: no or weak agitation, clothes not moving, clicking/ratcheting from the agitator area, or a loose/wobbly agitator
• Visual issues may include cracks, stripped splines, or a unit that lifts off easily

• Disconnect power and shut off water before servicing; wear cut-resistant gloves
• Remove the softener dispenser and cap, then the center bolt/retainer; pull the old agitator straight up
• Align splines and seat the new agitator fully; reuse existing bolt and cap unless damaged
• Do not overtighten the fastener; run a short test cycle to ensure proper agitation

This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:

• Converts drive motion into the back-and-forth action that moves laundry
• Circulates clothes to improve soil removal and reduce tangling
• Replaces cracked, stripped, or loose agitators that cause weak or no agitation
• Common symptoms include poor cleaning, clothes not moving during wash, or an agitator that wobbles or spins freely by hand

• 1 agitator assembly

• Disconnect power and turn off water supply before servicing
• Remove the fabric softener dispenser and inner cap to access the center bolt
• Remove the bolt, lift off the old agitator, seat the new agitator on the splined shaft, and secure the bolt
• Reinstall the cap/dispenser; reuse original hardware as applicable and check for a secure fit before testing

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly