Kenmore Refrigerator 253.51392106 (25351392106, 253 51392106) Parts

This replacement door handle restores a secure, comfortable grip for opening and closing your appliance door. Replace a cracked or loose handle to keep everyday use safe and convenient when the original is damaged or missing.

• Provides the handhold used to open and close the door
• Replaces cracked, broken, or missing handles to restore normal operation
• Addresses a wobbly/loose handle or stripped mounting points
• Common symptoms: handle broken, loose, or difficult to grip; trouble opening the door

• Disconnect power before servicing
• Support the door while removing and installing the handle
• Use the correct screwdriver; transfer any screw caps/end covers as needed and reuse original fasteners if applicable
• Tighten mounting screws evenly; do not overtighten, and ensure the handle is secure and aligned

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Capacitor-run,220 vac ,12 microfarad

This torsion spring mounts in the dispenser to return the ice chute door/flapper to the closed position after dispensing. Replacing a weak or broken spring helps stop warm air leaks, frost, and ice clumping in the chute.

• Provides the closing force for the dispenser ice door
• Helps seal the ice chute to reduce frost and moisture intrusion
• Typical symptoms: ice door won't close fully, frost/ice buildup around the chute, cubes dropping after dispensing, or air leakage at the dispenser
• Replace if the spring is broken, deformed, or has lost tension

• Disconnect power before servicing; shut off water if working near the dispenser area
• Remove dispenser trim/bezel and control panel to access the ice door assembly; support wiring harnesses
• Note spring orientation and preload before removal; install the new spring on the same hinge posts in the same direction
• Manually cycle the flapper to ensure smooth return and a full seal before reassembly

The Freezer Temperature Control is an OEM part for Frigidaire refrigerators. This part regulates the temperature inside the freezer compartment, maintaining the desired cooling level to keep your frozen foods fresh and preventing freezer burn.

Causes of a bad Freezer Temperature Control can include electrical issues, sensor failures, or mechanical wear over time.

Symptoms of a faulty Freezer Temperature Control include:

• Freezer temperature fluctuations or inability to maintain a consistent cool temperature 
• Freezer becoming too warm or not cold enough 
• Frost buildup or excessive ice formation inside the freezer 
• The refrigerator running constantly or cycling on and off frequently

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Includes service line.

Color: white. Measures about 11 inches wide by 4-1/2 inches high by 5 inches deep.

This augur nut is a genuine Frigidaire part, sold individually. It can be used as a replacement part for a refrigerator. This augur nut serves as a fastening component for the augur of an ice maker located inside the refrigerator; this nut maintains the placement of components within the ice maker so that ice and water can be dispensed properly and efficiently.An augur nut might have to be replaced if it is lost, misplaced, or stripped to the point that it is rendered ineffective. The primary sign of an augur nut that is missing or stripped is an ice maker that cannot dispense ice. If this is occurring, the infrastructure of the ice maker should be inspected, and if it is revealed that the augur nut is missing or has been stripped to the point that it cannot fasten its components, this genuine OEM replacement part should be ordered.This is an OEM part sourced directly from the manufacturer. It is sold individually. This augur nut is compatible with the following appliance brands: Frigidaire, Kenmore, Electrolux, Westinghouse, Tappan, Crosley, Gibson, and Universal.

The Ice Auger Drive Bar is an OEM replacement part for Frigidaire refrigerators. It plays an important role in allowing the icemaker assembly to function properly by transmitting rotational force from the motor to the ice auger. Without a properly functioning drive bar, ice cubes may not be dispensed as needed. Please Note: The nut is no longer separate. It is now part of this drive bar.

Causes of a bad ice auger drive bar can include wear and tear from frequent use, damage due to heavy ice loads, or corrosion from moisture exposure. A malfunctioning drive bar can result in inefficient ice dispensing or complete failure of the ice dispensing mechanism.

Symptoms of a bad drive bar include:

• Ice cubes not dispensing when requested
• Noise or grinding sounds coming from the icemaker area
• Stalling or failure of the icemaker assembly to rotate fully
• Inability to harvest or eject ice from the ice molding trays

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

The Light Switch is an OEM part for Frigidaire refrigerators. It is designed to control the interior lighting of the refrigerator; the switch activates when the door is opened and deactivates when closed. 

Causes of a bad Light Switch can include mechanical wear from frequent use, which may cause the switch to fail to engage or disengage properly. Electrical issues such as short circuits or loose connections can also prevent the switch from functioning correctly.

Symptoms of a bad Light Switch include:

• The refrigerator light staying on when the door is closed
• The light not turning on when the door is opened
• Flickering or intermittent lighting when the door position changes

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Nylon

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This spacer fits between the fixed crusher blades inside the refrigerator's ice bucket assembly. It preserves the correct gap and alignment so the auger turns freely and crushed ice dispenses smoothly without jams or grinding.

• Maintains the correct spacing between fixed crusher blades in the ice bucket
• Keeps the blade stack and auger aligned for smooth rotation
• Helps prevent ice jams, grinding noises, and inconsistent crushed-ice output
• Replaces a worn, cracked, or missing spacer discovered during service

• Disconnect power before servicing; remove the ice bucket from the freezer door/bin
• Carefully disassemble the crusher housing, noting the exact order of blades, spacers, and washers
• Wear cut-resistant gloves; crusher blades are sharp
• Reassemble in the original sequence and verify the auger turns freely before reinstalling

This meat pan is the refrigerator's deli drawer. Replacing a cracked or missing bin restores smooth sliding access for meats and cheeses and helps keep the fresh food section organized.

• Creates a dedicated compartment for deli items in the fresh food section
• Slides on existing shelf rails for easy access
• Restores proper fit when the original bin is cracked, warped, or missing
• Common symptoms: broken or missing drawer, front lip cracked, drawer falls or won't slide smoothly

• Remove contents; pull the old drawer straight out from the rails
• Inspect and clean the rails; transfer any reusable parts from the old drawer if applicable
• Align the new pan on the rails and slide it fully into place
• If movement is tight, confirm the shelf cover and rails are seated and level

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.