Kenmore Washer 417.27182704 (41727182704, 417 27182704) Parts

Genuine Frigidaire part

Screw`Pan Head `8 - 18Ab X 0.375 `39 `Cr/Sq Drive

By: Frigidaire

Part Number: 131243700

Do-It-Yourself Stories from Customers like You The bearing on the dryer drum wore out so bad the ball fell off Thomas J. • Green Bay , WI • October 31, 2016

I replaced the ball and socket connection for the drum. After doing so, I realized that the belt had been stretched and the tension pulley was not putting enough tension on the belt to turn the drum. After ordering a new belt, extra screw that was lost while disassembling the dryer, and some high temperature lubricant for the drum ball and socket the dryer now runs as well as it did when it was new. Read more

Genuine Frigidaire part

Washer Filter

4.7 (6)

By: Frigidaire

Part Number: 137518800

Do-It-Yourself Stories from Customers like You Wouldn't spin at first then no activity at all e23 code Levi G. • Wytheville , VA • March 06, 2017

We had a power surge that tripped the washer breaker. It showed an E23 error code so I replaced the main control board (part number AP4362398.) All washer activity back to normal except it still wouldn't spin and still had E23 code. I removed the tub to pump hose (part number AP3837322) to find all sorts of goodies inside such as underwires from bras, a quarter, nickel, penny, and dime stacked perfectly on top of each other inside the filter, and tangled yarn from a rug. Ended up replacing the... Read more

Genuine Frigidaire part

Drive Motor

4.7 (3)

By: Frigidaire

Part Number: 134869400

This OEM replacement part is a drive motor for washers. The drive motor is the main engine that propels the washer tub to spin and perform its primary function of washing clothes. Over time, a drive motor can lose power or stop working altogether due to excessive wear and tear. If the washer is no longer spinning or not working as efficiently as it once did, the drive motor will need to be replaced. Thankfully, replacing this part is a relatively easy fix.To begin, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the mounting screws. Once removed, gain access to the drive motor and remove the screws that attach it to the washer. After unthreading the screws, pull the drive motor out of its place and position the new motor in its original position. Fasten the mounting screws and make sure the motor is securely attached. This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore brand washers.

Do-It-Yourself Stories from Customers like You Front load washer Marcos O. • Pasadena , TX • October 30, 2015

Unplug washer then took back panel off. Unplug wires from motor then removed four screws from the motor housing then took old motor off and replaced it with new motor Read more

Genuine Frigidaire part

Switch-Pressure

5.0 (2)

By: Frigidaire

Part Number: 134438301

Do-It-Yourself Stories from Customers like You Water overflow Andrew M. • Woodbury , NJ • March 08, 2015

Replaced pressure switch and checked hose for any holes or cracks Read more

Genuine Frigidaire part

Drawer

5.0 (1)

By: Frigidaire

Part Number: 131271910

Do-It-Yourself Stories from Customers like You Dart on the despencer door broken Kathryn C. • Galesburg , IL • December 22, 2016

The lady that talked to Fred gave him great help. She told him how to take the front off to replace the part. It only took a couple of minutes to do the repair. Even though I work for Sears parts dept. he didn't think I knew what I was doing.. Read more

Genuine Frigidaire part

Door - Outer (Outer Door Panel)

3.5 (2)

By: Frigidaire

Part Number: 131278700

Outer door panel that replaces a damaged or worn outer door surface, restoring the appliance's finished exterior and protecting inner door components. Ideal when the exterior is dented, scratched, or cosmetically damaged. What it does

Provides the finished exterior surface for the appliance door and protects internal door components from damage.
Restores appearance after dents, scratches, rust spots, or cracked paint.
Re-establishes mounting surfaces and edge trim where tabs or attachment points are intact.
Helps prevent further corrosion or moisture intrusion into the door assembly.

What's included One outer door panel. Install notes

Disconnect power (and water, if applicable) and follow before starting; use proper PPE.
Door removal and panel replacement often require basic hand tools; save and reuse original screws, handles, and trim unless replacements are supplied.
Transfer any hardware, insulation, or inner-door pieces from the old door to the new panel as required.
Large panels can be awkward—have a second person assist to avoid dropping or bending the panel.

Do-It-Yourself Stories from Customers like You After 15 years the plastic door busted where the screws held the hinges on and leaked Joseph R. • Cerritos , CA • October 10, 2016

Purchased the door panels (both sides) and replaced them both. Not sure if spending $150 on door parts for a 15 year old washer was a great investment, but the parts worked great. Took maybe five minutes to put it all back together. Read more

Genuine Frigidaire part

Pulley - Drum - Reinfor

By: Frigidaire

Part Number: 131883400

Genuine Frigidaire part

Water Inlet Valve (115V)

5.0 (1)

By: Frigidaire

Part Number: 131900200

This 115V water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water supply when the valve fails. Designed to replace a faulty solenoid valve and stop leaks or no-water issues. What it does

Opens and closes water flow to the ice maker and door dispenser when energized.
Commonly replaces valves that hum, leak, or fail to allow water flow.
Stops intermittent or no-water conditions caused by a stuck or electrically failed valve.
Works with the fridge's control signals to deliver water only when needed.

What's included

One 115V water inlet (solenoid) valve as shown.

Install notes

Disconnect power and shut off the household water supply before replacing the valve.
Verify electrical connections and water line fittings are tight and leak-free after installation.
Handle inlet fittings carefully to avoid damage; use appropriate tools and avoid overtightening.

Do-It-Yourself Stories from Customers like You Water inlet valve. David T. • Rutherfordton , NC • August 08, 2021

Installed new one. Read more

Genuine Frigidaire part

Gasket - Seal

By: Frigidaire

Part Number: 131749200

Genuine Frigidaire part

Cover - Softener

By: Frigidaire

Part Number: 131272000

Genuine Frigidaire part

Spring - Boot

5.0 (1)

By: Frigidaire

Part Number: 131277300

Do-It-Yourself Stories from Customers like You Spider needed replaced due to corrosion & broke in 4 places Ellen T. • Mount Hope , WV • December 21, 2014

I took 11 year old washer apart, by watching step by step instructional video on this site. Found the problem & order the part (inner tub,shaft & spider). It's a shame you can't just order the spider, because the stainless steel tub & shaft were still perfectly good. Apparently, this is the manufactures way of making money. Anyway, I replaced part & washer is as good as new. The hardest part was having to have someone help lift the outer tub out & back in. Very happy, I did not have to buy a... Read more