Kenmore Dishwasher 665.13153K701 (66513153K701, 665 13153K701) Parts

This mount is a support bracket designed to secure internal components and reduce movement for a stable, quiet operation. It replaces worn or broken mounts to restore proper alignment and prevent rattling. What it does

• Supports and stabilizes internal parts to reduce vibration and noise
• Keeps components aligned to prevent uneven wear
• Helps stop rattling or clunking caused by a loose or damaged mount
• Used when a visible break, crack, or missing mounting point is present

• One mount/support bracket

• Disconnect power to the appliance before starting any repair
• Inspect surrounding parts and mounting hardware; replace damaged fasteners as needed
• Use proper tools and avoid over-tightening fasteners to prevent cracking the mount

This push-in retainer secures panels, trim or light-weight components inside the appliance to prevent vibration and movement during operation. It's a small, low-profile fastener that snaps into a pre-drilled hole for a clean, tool-free hold. What it does:

• Holds interior trim, access panels or wiring looms in place to reduce rattles and movement
• Replaces worn or broken plastic retainers that no longer grip securely
• Helps maintain proper alignment of lightweight components for reliable operation
• Can prevent loose parts from contacting moving components

• Disconnect power to the appliance before starting any work
• Access the area and remove any surrounding trim or panels as needed
• Align retainer with the hole and push straight in until it snaps or seats flush
• Inspect fit after installation; replace if damaged or does not secure properly

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

This interconnect board links the range/oven control console to the main electronics, restoring signal and power routing so the console and control functions communicate correctly. Designed as a direct replacement circuit connector. What it does:

• Routes signals and power between the user control console and the main control board
• Restores communication for touchpad/controls and display functions
• Can resolve symptoms like an unresponsive control panel, blank or flickering display, or failure to start cooking cycles
• Helps correct intermittent electronic behavior caused by loose or damaged connector circuitry

• Disconnect power at the breaker or unplug the appliance before beginning work
• Handle the board by the edges and avoid static discharge; use anti-static precautions if available
• Verify connector orientation and fully seat all ribbon cables and wire harnesses during reassembly

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

A small replacement door switch that tells the appliance when the door is closed so cycles can start—restores proper door-sensing to resolve no-start, intermittent operation, or control lockout issues related to a faulty door switch. What it does:

• Detects door open/closed state and completes the control circuit when the door is shut.
• Prevents the appliance from starting or running when the door is open.
• Commonly replaces a worn or broken switch that causes no-starts, stops mid-cycle, or intermittent operation.
• Works as the door-sensing safety/switching component in the door latch/closure assembly.

• Disconnect power (unplug or switch off breaker) before inspecting or replacing the switch.
• Match connector terminals and orientation to the original switch; secure wiring and terminals firmly.
• Inspect door latch and strike for damage or misalignment when replacing the switch.

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

This disk valve diverter directs wash water flow between spray arms and wash zones to restore proper circulation and cleaning performance. It replaces a worn or damaged diverter to help return consistent spray pressure and distribution. What it does:

• Routes pump water to the correct spray arm or wash zone during the wash cycle
• Helps maintain even spray pressure for effective cleaning
• Worn or broken diverter can cause poor cleaning, reduced water to a spray arm, or unusual pump noise
• Prevents bypass flow that can reduce wash performance

• One disk valve diverter as shown

• Disconnect power to the appliance and shut off the water supply before starting
• Access may require removing the tub access panel or disassembling spray arm/tub components
• Inspect surrounding seals and gaskets; replace any damaged parts to prevent leaks
• After installation, run a short cycle and check for proper water routing and leaks

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.