Kenmore Dishwasher 665.13242K901 (66513242K901, 665 13242K901) Parts

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This water inlet hanger secures the appliance's fill tube or line in the correct position, supporting a proper fill path and reducing strain on fittings. Replace a cracked or missing hanger to prevent movement, vibration, and potential leaks.

• Supports and positions the water inlet tube/line or inlet assembly
• Helps maintain alignment and sealing at the connection point
• Reduces vibration and prevents rubbing/chafing against surrounding parts
• Common symptoms include a loose or sagging inlet, rattling noises, chafed tubing, or drips from a misaligned inlet

• Disconnect power and shut off the water supply before servicing
• Access the inlet area and note the original hanger orientation and routing
• Remove the damaged hanger and mount the new hanger using the existing mounting points/fasteners
• Ensure the tube/line is secure and not kinked; restore service and run a brief test to check for leaks

12 Ft in length

Includes two screws, two clamps, and undercounter mounting brackets.

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

This dishwasher silverware basket organizes and secures your utensils during the wash, helping ensure thorough cleaning and preventing small items from slipping through the rack. Replace a cracked or missing basket to restore proper containment and convenience.

• Holds flatware and small utensils securely during wash cycles
• Helps prevent items from falling onto the tub floor or obstructing the spray arm
• Restores original organization and capacity when the basket is damaged or missing
• Common symptoms: cracked plastic, broken/large openings, unstable or loose basket, utensils tipping over

• Open the dishwasher and slide out the lower rack; remove the old basket
• Place the new basket in the original location/orientation and seat any tabs/hooks as designed
• Confirm the spray arm rotates freely with the basket installed
• No tools typically required; handle sharp utensils carefully

To order seal use WP8268340.

Color: Black.

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

Insulation pad that fits behind appliance panels to restore thermal protection and reduce noise. Replacing a damaged or missing pad helps protect nearby wiring and components from heat and can reduce vibration-related rattling. What it does:

• Provides thermal insulation to help limit heat transfer to adjacent panels and components.
• Dampens vibration and reduces rattling or buzzing caused by loose or worn insulation.
• Protects wires, connectors and plastic parts from excess heat when installed correctly.
• Common symptom: missing, torn, or deteriorated pad with increased exterior heat or noise.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove access panels as needed; position the pad flat against the cabinet surface or mounting area.
• Use original clips/adhesive or manufacturer-recommended fasteners to secure the pad; avoid covering vents or controls.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition