Kenmore Dishwasher 665.13269K110 (66513269K110, 665 13269K110) Parts

This spacer positions and supports the appliance tank/tub assembly to maintain proper alignment and spacing for reliable operation. Replaces a worn or damaged spacer to restore correct fit and reduce movement. What it does:

• Keeps the tank/tub assembly correctly spaced and aligned with the cabinet and mounting points
• Helps prevent rubbing, binding, and excess vibration caused by a missing or damaged spacer
• Restores proper clearance to support seals and hoses that rely on correct tank positioning
• Useful when reassembling the appliance after service or repair

• One spacer

• Disconnect power and water supply before starting any repair
• Access may require removal of outer panels, console, or access covers depending on model
• Handle parts carefully to avoid damaging surrounding seals and wiring; reuse fasteners unless replacement is specified

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This console assembly replaces the dryer control console to restore a finished front panel and allow access to the machine's controls. It provides the mounting surface and openings for the control board, timer, and user interface. What it does:

• Replaces a cracked, faded, or damaged control console to improve appearance and function
• Secures and protects the control board, timer, and user interface components
• Restores proper alignment and access to control knobs, buttons and display openings
• Helps resolve issues caused by loose or broken console mounting that affect button or knob operation

• One console assembly

• Power off and unplug the appliance before beginning work to avoid electrical shock
• Handle the console carefully to avoid scratching the finish and damaging clips or mounting tabs

This thermostat bracket secures the refrigerator/freezer temperature sensor or thermostat to the cabinet, keeping the sensor in the correct position for accurate temperature control. Durable replacement for factory mounting hardware. What it does:

• Holds the thermostat/temperature sensor in place so it reads interior temperatures correctly
• Helps prevent loose or misaligned sensors that can cause irregular cooling or cycling
• Restores proper sensor positioning after damage or broken mounting clips
• Works with the thermostat assembly to maintain consistent appliance operation

• One thermostat mounting bracket

• Disconnect power to the appliance before service to avoid electrical shock
• Handle thermostat/sensor elements carefully; avoid bending or pinching the sensing tube
• Retain or reuse original fasteners unless replacement hardware is explicitly included

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice

The Dishwasher Door Seal is an OEM replacement part for Whirlpool dishwashers. It provides a tight seal around the dishwasher door to prevent water, sound, and heat from escaping during the wash cycle. Measuring 71” in length (and stretching up to 75”), this door seal prevents water from leaking out during wash cycles.

Causes of a bad seal can include cracks, tears, or splits that develop due to regular use and age. Damage may also occur from over-tightening of the door or accidental impact.

Symptoms of a bad dishwasher door seal include:

• Water or moist air leaks around the door during a cycle  
• Higher energy bills due to hot air escaping
• Excess moisture or mineral deposits around the door seal area
• Food particles or debris trapped under a torn seal

This genuine OEM Whirlpool replacement seal is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This electronic control board is the appliance's central controller. It interprets user inputs and sensor signals to power components at the right time, restoring reliable operation when the original board fails.

• Interprets user settings and manages cycle timing and temperature control
• Switches relays/outputs to run motors, heaters, valves, fans, and lights
• Interfaces with sensors and safety switches to protect the appliance
• Symptoms can include no display or response, won't start, cycles that won't advance, or erratic operation
• Logs diagnostic error codes to aid troubleshooting

• Disconnect power before servicing; follow ESD precautions and handle the board by the edges
• Access the control area, then note/photograph wiring and move connectors one at a time to the new board
• Mount securely, ensure no wires are pinched, reassemble, and restore power
• Run a diagnostic or test cycle to confirm normal operation

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This spacer fits between tank components to maintain proper spacing and alignment, helping reduce vibration and wear. Use this genuine replacement to restore correct clearances and improve stability in the appliance's tank assembly. What it does:

• Positions and separates tank parts to maintain correct alignment during operation
• Helps reduce noise and vibration caused by misaligned components
• Prevents metal-to-metal contact that can cause premature wear or damage
• Restores factory clearances after service or replacement of tank parts

• One spacer

• Designed for direct replacement; use the OEM mounting location and orientation
• Disconnect power and water (if applicable) before beginning repair
• If fasteners or surrounding components are worn or damaged, replace them to ensure a secure fit