Kenmore Dishwasher 665.13422K701 (66513422K701, 665 13422K701) Parts

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

A small replacement door switch that tells the appliance when the door is closed so cycles can start—restores proper door-sensing to resolve no-start, intermittent operation, or control lockout issues related to a faulty door switch. What it does:

• Detects door open/closed state and completes the control circuit when the door is shut.
• Prevents the appliance from starting or running when the door is open.
• Commonly replaces a worn or broken switch that causes no-starts, stops mid-cycle, or intermittent operation.
• Works as the door-sensing safety/switching component in the door latch/closure assembly.

• Disconnect power (unplug or switch off breaker) before inspecting or replacing the switch.
• Match connector terminals and orientation to the original switch; secure wiring and terminals firmly.
• Inspect door latch and strike for damage or misalignment when replacing the switch.

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

Color: White

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This disk valve diverter directs wash water flow between spray arms and wash zones to restore proper circulation and cleaning performance. It replaces a worn or damaged diverter to help return consistent spray pressure and distribution. What it does:

• Routes pump water to the correct spray arm or wash zone during the wash cycle
• Helps maintain even spray pressure for effective cleaning
• Worn or broken diverter can cause poor cleaning, reduced water to a spray arm, or unusual pump noise
• Prevents bypass flow that can reduce wash performance

• One disk valve diverter as shown

• Disconnect power to the appliance and shut off the water supply before starting
• Access may require removing the tub access panel or disassembling spray arm/tub components
• Inspect surrounding seals and gaskets; replace any damaged parts to prevent leaks
• After installation, run a short cycle and check for proper water routing and leaks

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Also order air vent seal

This console assembly replaces the dryer control panel and restores user controls and display functions so you can select cycles and monitor status. It's a direct-fit service assembly for affected Whirlpool-brand dryers. What it does

• Houses the control board, user buttons, and display used to select cycles and options
• Restores unresponsive or damaged buttons, cracked panels, or missing display components
• Re-establishes a secure mounting surface for the appliance controls and user interface
• Helps resolve symptoms like non-working buttons, blank or damaged console, or loose control hardware

• One complete console assembly (control panel) as shown

• Disconnect power (unplug or switch off breaker) before starting any repair
• Some wiring harnesses and fasteners may need careful removal; label connectors as needed
• Handle the assembly gently to avoid cracking plastic or damaging the display and connectors