Kenmore Dishwasher 665.13859K601 (66513859K601, 665 13859K601) Parts

The Water Supply Tube is an OEM component specifically designed for connecting Whirlpool brand dishwashers to home plumbing systems. It transports water into dishwashers for cleaning and rinsing cycles.  

Potential causes of a problematic supply tube include mineral deposits reducing flow or small punctures from prolonged vibrations.

Symptoms of a faulty water supply tube include:

• Water leaks inside or underneath the dishwasher
• Inadequate water pressure impacting clean performance

Compatible models include some brands produced by KitchenAid, Maytag, and Kenmore.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This push-in screw cover conceals exposed fasteners or open screw holes on your appliance for a clean, finished look. It snaps into place to hide hardware and help keep dust and splashes out of the opening.

• Conceals visible screw heads or open screw holes on panels, doors, or trim
• Helps block dust and moisture from entering the opening
• Restores appearance when the original cap is missing or damaged
• Common symptoms: missing cap, cracked or loose cover, visible fastener or hole

• Align the cap with the hole and press in until fully seated and flush
• Clear any debris or old cap fragments from the hole to ensure a secure fit

This front seal sits at the leading edge of the dishwasher door opening to keep wash water and steam contained. Replacing a worn seal helps stop front-edge drips and protects adjacent cabinetry and flooring.

• Creates a watertight barrier along the front tub-to-door interface
• Helps prevent leaks at the bottom/front of the door during cycles
• Replace if the seal is cracked, flattened, torn, or missing
• Common symptoms: water under the kick panel, damp streaks at the front lip, visible wear

• Disconnect power and turn off the water supply before servicing
• Open the door, remove the old seal, and clean the front lip/channel thoroughly
• Center and press the new seal fully into place without stretching; ensure even compression
• Close the door and run a short test cycle to check for leaks

Color: Stainless

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Color: White

This replacement capacitor shield protects the appliance's capacitor from debris, contact and shorting, helping extend component life and reduce electrical faults. It installs over the capacitor to block dust, wiring contact and accidental damage. What it does:

• Covers and protects the capacitor from physical contact, dust and loose wiring
• Helps prevent short circuits and arcing caused by accidental contact with the capacitor
• Useful when existing shield is cracked, missing or deformed
• Can reduce risk of intermittent electrical faults related to exposed capacitor

• One capacitor shield (protective cover)

• Always disconnect power to the appliance before servicing
• Capacitors can hold a charge; discharge safely before touching electrical components
• Remove necessary access panels to reach the capacitor; replace shield without stressing wires