Kenmore Dishwasher 665.13963K012 (66513963K012, 665 13963K012) Parts

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

Drain hose (loop) that routes washer wastewater and forms a high drain loop to help reduce backflow and siphoning. Replaces cracked, kinked, or deteriorated drain hoses to restore proper draining and reduce leaks. What it does:

• Directs wastewater from the appliance to the household drain to maintain proper drainage.
• Forms a high drain loop to help prevent backflow and siphoning into the washer.
• Replaces worn or damaged hoses that can cause leaks, slow draining, or standing water.
• Works with the appliance's factory drain connection and clamps.

• Disconnect power and turn off the water supply before servicing.
• Route hose to create a high loop above the cabinet connection and secure with clamps to prevent kinks or sagging.
• Use appropriate clamps or fasteners and tighten connections; inspect for leaks after restoring power and water.

This electronic control board is the dishwasher's main "brain," coordinating the fill, wash, drain, and dry sequences. Replacing a failed board can restore normal operation when the dishwasher is unresponsive, won't start cycles, or behaves erratically.

• Directs power and timing to valves, pumps, and heater for each cycle step
• Monitors inputs from sensors and the door latch to advance or pause the cycle
• Communicates with the user interface for button inputs and status lights
• Typical failure symptoms: no power to controls or won't start; stops mid-cycle or won't advance; blinking lights or error codes; intermittent operation

• Disconnect power at the breaker before servicing; verify no power at the dishwasher
• Access location varies by model; commonly behind the lower toe panel in a protective control housing
• Handle the board by the edges and use ESD protection; move wire connectors one at a time to the new board and secure the housing
• After installation, run the built-in diagnostics per the tech sheet; some models may require control configuration

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

This disk valve diverter directs wash water flow between spray arms and wash zones to restore proper circulation and cleaning performance. It replaces a worn or damaged diverter to help return consistent spray pressure and distribution. What it does:

• Routes pump water to the correct spray arm or wash zone during the wash cycle
• Helps maintain even spray pressure for effective cleaning
• Worn or broken diverter can cause poor cleaning, reduced water to a spray arm, or unusual pump noise
• Prevents bypass flow that can reduce wash performance

• One disk valve diverter as shown

• Disconnect power to the appliance and shut off the water supply before starting
• Access may require removing the tub access panel or disassembling spray arm/tub components
• Inspect surrounding seals and gaskets; replace any damaged parts to prevent leaks
• After installation, run a short cycle and check for proper water routing and leaks

This plate-latch strike secures the appliance door by engaging the latch assembly so the door stays closed during operation. It replaces a worn or damaged strike to restore proper door closure and reliable operation. What it does:

• Provides a sturdy contact point for the door latch to engage and hold the door closed
• Helps prevent the door from popping open during use, which can cause cycle interruption
• Addresses symptoms like a door that won't stay latched, won't close fully, or causes the unit to stop mid-cycle
• Works as the mating strike for the existing latch assembly to ensure proper alignment

• One plate-latch strike

• Disconnect power to the appliance before beginning any repair
• Access the strike by opening the door; remove any trim or screws as needed to reach the strike mounting location
• Install replacement in the same orientation as the original and tighten fasteners securely without over-torquing
• After installation, verify the door latches smoothly and the appliance completes its normal cycle

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This spacer fits between tank components to maintain proper spacing and alignment, helping reduce vibration and wear. Use this genuine replacement to restore correct clearances and improve stability in the appliance's tank assembly. What it does:

• Positions and separates tank parts to maintain correct alignment during operation
• Helps reduce noise and vibration caused by misaligned components
• Prevents metal-to-metal contact that can cause premature wear or damage
• Restores factory clearances after service or replacement of tank parts

• One spacer

• Designed for direct replacement; use the OEM mounting location and orientation
• Disconnect power and water (if applicable) before beginning repair
• If fasteners or surrounding components are worn or damaged, replace them to ensure a secure fit

This silverware basket holds forks, knives and spoons during the wash cycle to keep utensils separated and upright for better cleaning and to prevent small items from falling to the tub. Durable plastic construction provides a simple, removable storage solution for the lower rack. What it does:

• Secures and separates silverware and small utensils to reduce nesting and promote cleaner results
• Keeps loose items from falling into the wash area or blocking the spray arms
• Helps prevent rattling and movement of cutlery during the cycle
• Designed to sit in the dishwasher's lower rack for easy loading and unloading

• One (1) silverware basket

• Remove the lower rack before installing to position the basket securely in the rack bays
• Replace only when the dishwasher is off and no cycle is running; follow basic safety precautions
• Inspect for cracked or broken tabs that could allow the basket to shift during use
• Clean periodically to remove food buildup and avoid odors