Kenmore Dishwasher 665.13979K012 (66513979K012, 665 13979K012) Parts

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This sump and motor assembly replaces the lower tub sump with the circulation pump pre-installed. It restores proper water recirculation to the spray arms and a tight seal at the tub floor to help reduce leaks and noise.

• Circulates wash water through the spray arms for consistent cleaning performance
• Channels and filters water beneath the tub via the integrated sump
• Maintains a watertight seal at the tub base
• Common symptoms of failure: weak or no spray action, poor cleaning results, loud humming/grinding during wash, or water leaking from the center bottom area

• Disconnect power and turn off the water supply before servicing; allow internal components to cool
• Remove the lower rack, spray arm, and filters to access the sump; disconnect hoses and wiring, then release the locking tabs to remove the assembly
• Ensure all seals/O-rings are properly seated; fully engage hose and electrical connections to prevent leaks
• After installation, run a brief test cycle and inspect carefully for leaks before reassembling panels

Color: light grey. It measures about 2-1/2 inches high by 2 inches deep.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

This de-coupled drain housing creates a sealed, vibration-isolated connection in the appliance's drain path. Replacing a cracked or leaking housing restores reliable draining performance and helps prevent water leaks and rattling during the drain cycle.

• Forms the rigid, sealed connection between the drain path and mating components
• Isolates pump vibration from the chassis to reduce noise during drain
• Directs wastewater efficiently out of the unit during the drain cycle
• Common symptoms of a failed housing include standing water, leaks under the unit, loud vibration/buzzing while draining, or visible cracks/broken tabs

• Disconnect power and water supply before servicing; allow any hot water to cool
• Access the drain area and place a towel or pan to catch residual water
• Move clamps/hoses, then transfer any reusable seals or grommets; replace worn seals as needed
• Secure all connections and clamps; run a short test and check carefully for leaks

Includes two screws, two clamps, and undercounter mounting brackets.

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

This spray arm distributes wash water inside the dishwasher, rotating to deliver even spray coverage across the racks. Replace a cracked or clogged arm to restore consistent cleaning performance and reliable water distribution.

• Directs pressurized water through jet openings while spinning to wash dishes evenly
• Helps address symptoms such as poor cleaning results or uneven spray coverage
• Replace if the arm is cracked, warped, mineral-fouled, or no longer spins freely
• Damage or improper seating can cause the arm to strike dishes/tub and make noise

• Disconnect power to the dishwasher before servicing
• Remove rack(s) if needed; release the arm by unscrewing the retainer or pressing the locking tab (method varies by model)
• Clean debris from the mounting hub and seal surfaces before installing the new arm
• Seat fully, ensure the arm spins freely with proper clearance, then run a test cycle

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Drain hose (loop) that routes washer wastewater and forms a high drain loop to help reduce backflow and siphoning. Replaces cracked, kinked, or deteriorated drain hoses to restore proper draining and reduce leaks. What it does:

• Directs wastewater from the appliance to the household drain to maintain proper drainage.
• Forms a high drain loop to help prevent backflow and siphoning into the washer.
• Replaces worn or damaged hoses that can cause leaks, slow draining, or standing water.
• Works with the appliance's factory drain connection and clamps.

• Disconnect power and turn off the water supply before servicing.
• Route hose to create a high loop above the cabinet connection and secure with clamps to prevent kinks or sagging.
• Use appropriate clamps or fasteners and tighten connections; inspect for leaks after restoring power and water.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

Insulation pad that fits behind appliance panels to restore thermal protection and reduce noise. Replacing a damaged or missing pad helps protect nearby wiring and components from heat and can reduce vibration-related rattling. What it does:

• Provides thermal insulation to help limit heat transfer to adjacent panels and components.
• Dampens vibration and reduces rattling or buzzing caused by loose or worn insulation.
• Protects wires, connectors and plastic parts from excess heat when installed correctly.
• Common symptom: missing, torn, or deteriorated pad with increased exterior heat or noise.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove access panels as needed; position the pad flat against the cabinet surface or mounting area.
• Use original clips/adhesive or manufacturer-recommended fasteners to secure the pad; avoid covering vents or controls.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning