Kenmore Dishwasher 665.15951792 (66515951792, 665 15951792) Parts

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

includes seal

Included with nut.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Detergent cup dispenser actuator assembly.

Includes washers.

Size: 7 foot long.

Almond. Size: 13 oz. can. Acrylic appliance paint.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

This is a tine pivot clip that is a part of the dishrack on many models of dishwashers. The purpose of the plastic tine pivot clip is to secure the tine row onto the dishrack so it stays in the correct place. Sometimes, the tine pivot clip can be damaged or cracked through typical use. When this occurs, the tine row may move out of place and cause noise or other damage to the dishwasher. If a visual inspection shows damage to the tine pivot clip, it should be replaced.Work gloves will be needed to replace the tine pivot clip. In most cases, the replacement can be done by hand but pliers may also be useful. Unplug the dishwasher and disconnect the water before making the replacement. Open the dishwasher and gain access to the tine pivot clip. Pull it out of the dishwasher and install the new replacement part. Make sure to reconnect the water and power before use.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part. The tine pivot clip is designed to be compatible with dishwashers manufactured by Kenmore, KitchenAid, and Whirlpool.

This small check ball sits inside a check valve to allow one-way water flow. Replacing a worn or missing ball helps prevent backflow and supports reliable draining performance between cycles.

• Maintains one-way flow through the valve to stop water from returning after the pump stops
• Helps ensure complete, consistent draining
• A damaged, swollen, or missing ball can let water back up into the tub/sump
• Contribute to slow or intermittent draining and unusual gurgling/flow noises

• Disconnect power and shut off water before servicing
• Access the check valve assembly per your model's service information (commonly at the sump, pump outlet, or drain connection)
• Clean the valve seat/passage; remove debris that could prevent sealing
• Place the ball in the valve seat as shown in your model's parts diagram; reassemble and test for leaks and proper flow

Color: Almond

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

Comes with axle clip.