Kenmore Dishwasher 665.15987990 (66515987990, 665 15987990) Parts

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement wheel restores smooth movement for the appliance's moving assembly, helping reduce noise and prevent binding for consistent operation. Ideal when worn or damaged wheels cause dragging or uneven motion. What it does:

• Supports and guides a rotating or sliding component to maintain smooth movement
• Reduces friction and prevents binding that can cause rubbing or grinding noises
• Helps stabilize moving parts to eliminate wobble and uneven operation
• Restores proper alignment so the assembly runs quietly and reliably

• Disconnect power to the appliance before starting any repair
• Inspect surrounding mounts and clips for damage; replace if worn
• Use basic hand tools; avoid forcing parts to prevent damage

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This seal kit is for the main tub. It goes around the pump housing.

Notes: Only one screw hole is used now.

Note: There are four wheel assemblies includes with this rack. The flexible tine rows are not included. This is a lower dishrack assembly for a dishwasher. This part holds the dishes during the washing and drying cycles. Note that this is only the lower dishrack assembly and the upper dishrack assembly is sold separately. Over time, the lower dishrack assembly may begin to rust or the coating may wear off. It is also possible that sections of the part could break due to degradation over time. If this happens, the entire lower dishrack assembly will need to be replaced. The lower dishrack assembly is compatible with dishwashers that are manufactured by the Kenmore, KitchenAid, and Whirlpool brands. It comes straight from the manufacturer and is sold individually. It's a genuine, high-quality, and durable OEM part.

Screw for wash impeller.

This overfill control switch (float switch) senses water level and helps stop the fill valve to prevent overfilling. It replaces a worn or failed water-level safety switch to restore proper fill control and reduce overflow risk. What it does:

• Detects high water level and signals the washer control to stop filling
• Helps prevent water overflow and unintended flooding when working correctly
• Commonly linked to symptoms like continuous filling, overfilling, or washer not advancing cycles
• Interfaces with the washer control board and fill valve to maintain proper water level

• One overfill control switch (float switch)

• Disconnect power and turn off water supply before starting any repair
• Handle connectors gently; confirm wiring positions or take a photo before disconnecting
• Verify proper operation after installation by running a short fill cycle and checking for correct shutoff