Kenmore Dishwasher 665.1765191 (6651765191, 665 1765191) Parts

This dishrack replaces a damaged, rusted, or warped rack to restore smooth loading and secure support for dishes. A solid rack keeps items upright for better spray coverage, cleaner results, and helps prevent rust transfer and chipping.

• Holds and organizes plates, bowls, and cookware for proper spacing and spray access
• Provides stable support to reduce tipping and breakage during wash cycles
• Replaces racks with rust, broken wires, or bent/missing tines
• Can help resolve issues like rust marks on dishes and loading difficulties

• Disconnect power at the breaker before servicing
• Open the door; slide the old rack out—on some models, release rack stops to remove
• Transfer any reusable accessories from the old rack to the new rack if applicable
• Wear cut-resistant gloves; set the new rack on the rails and verify smooth movement and proper door closure

This seal kit is for the main tub. It goes around the pump housing.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Screw for wash impeller.

This lower spray arm assembly circulates pressurized wash water across the bottom rack to help remove food soil and improve cleaning. It replaces a worn or damaged lower arm to restore proper spray coverage. What it does:

• Directs water flow from the pump to wash dishes on the lower rack.
• Helps maintain even spray pattern and consistent cleaning performance.
• Can prevent poor cleaning or missed spots caused by cracked, clogged, or broken arms.
• Connects to the dishwasher's spray tube or hub to rotate during the wash cycle.

• Disconnect power to the dishwasher before servicing.
• Remove the lower rack to access and remove the old spray arm; typically snaps or unscrews from the hub.
• Inspect the spray arm hub and spray tube connection for debris before installing the new arm.
• Reinstall the lower rack and run a short cycle to verify proper rotation and no obstructions.

This premium dispenser cam engages the dispenser mechanism to control door/lever movement and ensure reliable dispense actions. It replaces a worn cam to restore proper dispenser function and consistent operation. What it does:

• Rotates and times the dispenser lever/door so the dispenser opens and closes correctly
• Transfers motion from the actuator to the dispenser linkage or switch
• Commonly used when the dispenser lever feels loose, doesn't return, or dispensing is intermittent
• Helps stop unwanted continuous dispensing caused by a worn cam surface

• Disconnect power (and water supply if applicable) before starting work
• Access the dispenser assembly; removal of the dispenser bezel or control housing may be required
• Handle small plastic parts carefully to avoid breaking tabs; align cam on shaft before reassembly
• Test dispenser operation after reassembly to ensure correct movement and sealing

Size: 8-32 x 1/4 inch.

This small cupshelf is the replacement door shelf insert that restores secure storage for cups, glasses and small items in your refrigerator door. It helps organize the door and prevents items from shifting or falling. What it does:

• Replaces a cracked, broken or missing small cupshelf to restore door storage capacity
• Supports cups, small glasses and lightweight containers on the refrigerator door
• Helps keep items organized and prevents sliding when the door opens or closes
• Matches OEM fit and mounting points when used as the specified replacement part

• One small cupshelf

• Remove items from the door and lift out the old shelf; align tabs and snap the new shelf into the existing door mounts
• No special tools are typically required; handle carefully to avoid damaging door trim or mounting tabs
• Always follow refrigerator power/safety guidance from the manufacturer when working near controls or lights

Size: 8-32.

This lower wash arm bearing keeps the dishwasher's lower spray arm turning smoothly so dishes get even water coverage. It replaces a worn bearing to reduce noise and restore proper spray-arm rotation. What it does:

• Supports the lower spray arm so it can spin freely during cycles
• Helps maintain even water distribution for better cleaning
• Reduces grinding or scraping noises caused by a worn bearing
• Prevents wobbling or misalignment of the lower spray arm

• Disconnect power and shut off the water supply before starting any repair
• Inspect the spray arm and mounting surfaces for damage; clean before installing the new bearing

The Latch Switch Kit, an OEM Replacement Part is designed to ensure the safe operation of your Whirlpool dishwasher. The kit includes two microswitches and a wiring harness. It prevents the appliance from running when the door is open. If defective, the door switch may prevent the dishwasher from operating even when the door is closed.

Causes of a bad door switch can include wear and tear, exposure to moisture, or a broken actuator.

Symptoms of a bad door switch include:

• Dishwasher not starting
• Dishwasher stopping mid-cycle
• Error codes related to door issues
• Dishwasher running with the door open

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.