Kenmore Dishwasher 665.17755790 (66517755790, 665 17755790) Parts

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

These dishwasher cleaner tablets help dissolve and remove limescale, mineral deposits, and odor-causing residues from the tub and spray system. Use monthly or as needed to help maintain cleaning performance and a fresh-smelling interior.

• Breaks down hard-water scale and detergent film that can accumulate inside the dishwasher
• Helps reduce lingering odors caused by trapped residues
• Supports proper spray performance by cleaning internal surfaces and passages
• Helpful when you notice white film, cloudy glassware, or persistent smells

• Run with the dishwasher empty; follow the package directions for tablet placement and cycle selection
• Do not add other cleaners or detergent during the cycle
• Keep out of reach of children; avoid contact with eyes; wash hands after handling
• For heavy buildup, repeat use per label instructions

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This seal kit is for the main tub. It goes around the pump housing.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Screw for wash impeller.

This pump outlet directs drained water from the washer's pump housing into the drain hose, helping the appliance remove wastewater efficiently. Replacing a damaged outlet restores proper drainage and reduces leaks. What it does:

• Channels water from the pump to the drain hose to enable normal draining
• Seals the pump discharge to prevent leaks at the pump exit
• A cracked or clogged outlet can cause slow or no-drain symptoms, leaks under the washer, or water pooling
• Works with the pump assembly to maintain correct water flow during drain cycles

• One pump outlet and the part shown as item 13 in the OEM diagram

• Disconnect power (unplug or switch off breaker) before beginning service
• Turn off and disconnect water lines if needed and place towels to catch residual water
• Inspect and replace any worn clamps, gaskets, or seals when installing the outlet
• Recheck connections and test a short drain cycle after installation to confirm no leaks