Kenmore Dishwasher 665.17769K600 (66517769K600, 665 17769K600) Parts

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

This durable silverware basket holds forks, knives and other utensils securely during dishwasher cycles so small items stay corralled and clean. Fits into the dishwasher rack to keep cutlery organized and prevent items from falling through. What it does:

• Holds and organizes silverware and small kitchen utensils during wash cycles
• Keeps utensils upright and separated for better cleaning and drying
• Prevents small items from slipping into the dishwasher spray area or drain
• Replaces cracked, broken or missing baskets that allow cutlery to scatter

• No tools required; remove the lower rack and set the basket into the designated rack slots
• Ensure basket snaps or rests securely and does not interfere with rack movement or spray arms
• Inspect basket for cracks or sharp edges before use; discontinue use if damaged
• Always follow the appliance manufacturer's safety and installation instructions

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This replacement power cord supplies mains power to an electric range or oven, restoring reliable power delivery so the appliance can heat and operate normally. Designed as a direct-fit electrical cord for compatible models. What it does:

• Delivers line and ground connections from the wall outlet to the appliance electrical terminal
• Replaces a damaged, frayed, or burnt cord that can cause intermittent power or no power to the range/oven
• Helps eliminate loose connections that produce arcing, overheating, or tripping breakers
• Provides a correct, durable power connection when the OEM cord has failed

• Disconnect power at the main breaker or fuse box before starting work
• Access the appliance terminal block (usually behind a rear access panel) and reattach wires to the correct terminals
• Use proper wire connectors and tighten terminal screws to the manufacturer's torque; secure strain relief per the appliance design

This seal kit is for the main tub. It goes around the pump housing.

Notes: Only one screw hole is used now.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Screw for wash impeller.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

This heater support secures the dryer heater assembly so it stays aligned and stable during operation, helping maintain proper airflow and heating performance. It's a direct-fit replacement designed to restore correct heater positioning. What it does:

• Holds the heater assembly in place to prevent shifting or contact with other components
• Helps maintain proper airflow path for efficient drying and consistent heat
• Reduces rattling, rubbing, or intermittent heating caused by a loose heater
• Works with the heater housing and mounting points to keep electrical and thermal parts separated

• Refer to the dryer's service manual or parts diagram for correct placement and orientation
• Disconnect power before starting work to avoid electrical shock
• Inspect surrounding clips, screws, and the heater assembly; replace any damaged fasteners