Kenmore Dishwasher 665.1779582 (6651779582, 665 1779582) Parts

Touch-up paint for repairing small chips, scratches and scuffs on painted appliance surfaces. Restores the appearance of localized damage so repaired areas better blend with the surrounding finish. What it does:

• Covers small chips and surface scratches to improve cosmetic appearance.
• Helps conceal finish wear on painted metal and plastic trim.
• Lets you spot-repair without replacing large panels or parts.
• Works for quick, visible fixes where full repainting isn't needed.

• Clean and dry the repair area thoroughly before applying; remove loose paint or rust.
• Test on an inconspicuous area first to confirm color match and compatibility.
• Apply sparingly in thin coats with a small brush or cotton swab; allow each coat to dry before adding more.
• Use in a well-ventilated area and keep out of reach of children; follow any handling instructions on the product label.

A small mounting clip that secures interior panels or trim pieces to the appliance, keeping parts aligned and preventing rattling or movement during operation. Simple replacement restores proper fit and reduces noise from loose components. What it does:

• Holds a panel, trim or small component in place on the cabinet or housing
• Keeps parts aligned so doors, panels or covers fit and operate smoothly
• Prevents rattling or vibration caused by loose or missing fasteners
• A worn or broken clip can allow gaps, movement, or noise during use

• Disconnect power (unplug or switch off breaker) before servicing
• Replacement typically requires only basic hand tools; keep track of any removed fasteners
• Inspect surrounding mounting points and adjacent clips for wear and replace as needed

Color: White. Size: 13 oz. Spray paint primer. can.

This small lever seal fits the dishwasher's detergent cup/dispenser. It seals around the lever/shaft to keep wash water out of the cup until the release cycle, helping deliver detergent at the right time for effective cleaning.

• Creates a watertight seal around the detergent cup lever/pivot
• Helps keep detergent dry until the main wash
• A worn or shrunken seal may allow early detergent washout or water in the cup before it opens
• Replacing the seal can help restore proper dispenser performance

• Disconnect power to the dishwasher before servicing
• Access the dispenser from the inner door; note lever and seal orientation
• Remove the old seal, clean the groove/shaft, and press the new seal fully into place
• Reassemble and run a short cycle to verify proper dispenser operation

This replacement caster and socket assembly restores smooth rolling and stable support for the appliance cabinet. Use it to replace a worn or damaged wheel and mounting socket so the appliance moves easily and sits level. What it does:

• Provides a rolling wheel and mounting socket to support appliance movement and weight.
• Replaces cracked, seized, or worn casters that cause dragging, sticking, or uneven motion.
• Helps reduce noise and cabinet scuffs from a damaged or loose wheel.
• Restores proper alignment when the appliance tilts or does not roll smoothly.

• Disconnect power and water and move the appliance to a safe, stable work area before starting.
• Support the appliance to prevent tipping when removing/installing the caster.
• Remove any trim or mounting hardware covering the caster; match orientation and fasteners when installing the replacement.
• After installation, verify the appliance rolls smoothly and sits level; tighten fasteners as needed.

This dishwasher air gap prevents backflow from the sink into the dishwasher drain line, helping keep wastewater out of the appliance and reducing odors. It provides a simple, code-friendly way to vent the drain hose at the sink. What it does:

• Creates an air break in the dishwasher drain to prevent soiled water from flowing back into the machine
• Helps the dishwasher drain properly and reduces standing water in the tub or sink
• Reduces odors and contamination risk caused by backflow through the drain hose
• Works with most standard sink-mount dishwasher drain hose setups

• Designed for sink-mount installation; follow sink and dishwasher manufacturer instructions and local plumbing codes
• Use appropriate hose clamps and a secure hose connection to prevent leaks
• Inspect and clean the air gap periodically to remove debris

This seal kit is for the main tub. It goes around the pump housing.

For Whirlpool made dishwashers. Assembly includes one spring, one retainer and one protective tip. Replace both springs at the same time to prevent uneven load.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

Screw for wash impeller.

This door spring retainer secures the dryer/washer door spring to the cabinet so the hinge spring stays in place for reliable door movement and alignment. It prevents the spring from slipping or disengaging during normal use. What it does:

• Holds the door spring end in the correct position so the hinge maintains proper tension
• Helps prevent door sagging, misalignment, or a door that won't stay closed
• Keeps the spring secured to reduce rattling or intermittent disengagement
• Works with the existing door hinge/spring assembly to restore reliable opening and closing

• Disconnect power (and gas if applicable) before any service; wear gloves and eye protection
• Access typically requires opening or removing the dryer/washer front or top panel; follow OEM service manual for steps
• Retaining springs are under tension—carefully release and re-seat springs to avoid sudden movement
• If other hinge or spring hardware is damaged, replace those parts to ensure safe operation

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.