John Doe January 18, 2013 for Model Number GLWS1339ESO Trying to remove/ replace a Agitator. Is there a video for this?
1 Answer Hello John Doe. Remove the cap by pulling it off and then the dust cover under it. Next, remove the screw and lift out the agitator. Read More...
John Doe January 18, 2013 for Model Number GLWS1339ESO The four fins at the bottom of the agitator are almost completely gone. (There is only one left). Is there a illustration that could take me through how to remove the agitator?
1 Answer Hello John. Pull off the cap number 66 in diagram and then pull off dust cover number 67. Then remove the bolt and washer numbers 56 and 57 and lift out the agitator. Here is a link to the diagram. http://www.appliancepartspros.com/motor-tub-parts-for-frigidaire-glws1339es0.html Read More...
Gabe December 08, 2012 for Model Number FE2831AS1 My washer wobbles bad when it spins dry. my old one had straps to prevent that this one doesnt. What esle would it be?
1 Answer Hello Gabe, The model number listed is not showing as a good model number. We will need you to verify the model in order for us to assist you better. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Missy November 18, 2012 for Model Number GLWS1439FS1 My washer will not agitate but it will spin out & drain. The top part of the agitator will spin freely both ways by hand. I've checked it without any clothes in it & the problem still exists. Would this mean it needs a new agitator?
1 Answer Hello Missy. Yes, based on the information you provided, it sounds like the agitator 131605901 needs to be replaced. Read More...
Mleckson October 01, 2012 for Model Number FWS1233FS0 I'm attempting to take apart the agitator on my washer to check if the dogs need to be replaced (fairly certain that is the problem). However, no matter how hard I pull the upper agitator is not separating from the lower one. Will I need to replace the entire agitator with this model?
1 Answer Hello Mleckson. Sorry, but there is no dogs used in this model. You will need to replace the agitator 131605901 in the unit. Read More...
Henry March 15, 2012 for Model Number 131605901 How would I be sure of the cam size, I'm seeing different videos from you guys but nothing helps indicate how to determine the correct size of the cam, so I can get the right part. it seems that my stack-able is not being made anymore, or so it would seem...so I'm concerned that these videos may not apply...help, please
1 Answer Hello Henry. We will need your model number to help you with the cam size. Please post your model number with a new question on the parts page. Thank you. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Henry March 14, 2012 for Model Number 131605901 My kenmore agitator isn't agitating properly. I've removed the whole thing but can seem to get to "dogs" which I think may be the problem (thanks to some previous posts). I would appreciate help with how to disassemble agitator (top part) to get to the dogs.
1 Answer Hello Henry. Here is a link to a video to show you how to remove the dogs. Hope this helps. http://www.youtube.com/watch?v=ensJz0h6wLM Read More...
Kevin January 31, 2012 for Model Number 41797922700 Above the agitator is a hollow shaft with fins on it. Above this is the softener cup and cap. At some point everything but the lower agitator "popped" off. Probably from an unbalanced load. I can't seem to get it back together. I might be missing parts. I no longer have the flat cap. How do I get it back together?
1 Answer Hello Kevin. Based on the information you provided, it sounds like the agitator 131605901 is bad and will need to be replaced. Hope this helps. Read More...
Emilee January 05, 2012 for Model Number FWSB7800DS The dogs in my agitator are worn out and I need to replace them. I'm not sure if I have to buy the whole agitator or if I can just buy the dogs...... I removed the bolt but am unable to get to the dogs. Can you help?
1 Answer Hello Emilee. Remove the agitator from the washer and place it on the floor. Grasp the top and while standing on the bottom, jerk the top part upward to separate the two pieces. Now you can access and replace the dogs 80040. Hope this helps. Read More...
Curt June 02, 2011 for Model Number FWS1339AC1 A question was previously asked in how to remove the agitator with a broken fin. The answer was to remove the cap to access a bolt. Well ..., how do you remove the cap. I have jerked, twisted, turned and pried with no results. What is the procedure in removing the cap?
1 Answer Hello Curt. The cap pulls off the agitator. They can be tight and hard to remove on some models. Hope this helps. Read More...