Dave F January 15, 2016 for Model Number LGHS2667KE0 Hello, I have a Frigidaire gallery model # LGHS2667KE0 when I plug my refrigerator in the lights turn on and off and there is a clicking noise. What do I need to fix this? Thanks
1 Answer Dave, The most likely cause for the unit having a clicking noise and the lights going on and off would be a faulty control board. Read More...
Roger July 15, 2015 for Model Number LGHS2667KE0 Hi, I ordered the 5303918498 (AP4695205) main control board for my fridge since the old control board left a SY CE error. I also ordered the door circuit board and replaced that as well. The old Main control board would click. After installing the new board, the fridge doesn't even power on. Is it possible that the new board is bad or the wires to connect to the existing wires could be something wrong with them? Otherwise I have no idea why it won't power on at all now but still does with the old damaged board. Thanks
1 Answer Roger, It is possible that you may have received a mispackaged control board but there have been some issues with the control board and would recommend contacting the manufacturer to make sure that the part number you received is the correct one and let them know of the issue with the unit not powering on after installing. Also try to install not using the wire harness that came with the control board if possible. Read More...
Drcafe June 02, 2015 for Model Number FPHS2699KF0 How to replace control board 242000406 with 5303918498.....not all connection wires are on the new board.
1 Answer Hello Drcafe, You need to use the wiring harness sent with the new board and hook them into the connectors on the unit. Read More...
John February 01, 2015 for Model Number FGHS2367KB2 Refrigerator is not cold enough. the freezer is fine. The temp display will read a higher temp than what the fridg actually is. If the temp sensor is unplugged the fridge will get too cold and freeze the food. with the sensor unplugged the temp display will go to 33 deg. I have replaced the temp sensor and have the same result.
1 Answer John, With a new sensor not correcting the issue with the refrigerator not getting cold enough, this issue would most likely be caused by the control board of the unit. Read More...
Rich September 30, 2014 for Model Number Frigidaire fgh2655kpo I purchased a control board 5303918498 from you and plugged in to the refrigerator and nothing happened. Just like Glenn's Question. The old board simply cycled on and off. Do I need to replace the other control board. If so what is the number?
1 Answer Rich, If you had the SY CE error code then yes the dispenser control board may also need to be replaced. We are unable to give you the part number as the model number is not coming up as a valid model. Read More...
Denise T July 02, 2014 for Model Number LGHS2665KF I just order this part for my frigidaire refrigerator. Part#AP4695205. I am trying to locate where this part is located on the fridge. Can you help with the location of where this part would go?
1 Answer Denise, When you pull the kick panel from the bottom of the refrigerator, there will be 2 openings. look in the left opening and the control will be locate there by a single 1/4" hex head screw. Read More...
Carl D June 12, 2014 for Model Number FGHS2634KQ2 I've had the same issue with this board. Customer complaint ; Warm fresh food . Unit not defrosting. Manually defrost ,check heater and thermostat. All check good . Power board has defrost built in. Order new board 3 times. Unit will not power up after new board is installed. Check for power to board , No issue with turning unit on with old board. I have to assume that the new boards are incompatible. Any suggestions? Thank you Carl
1 Answer Hello Carl. Your model number calls for part number 5303918525 for the main control board. You may have ordered the wrong control board for the unit. Read More...
Where Is The Main Control Board Located? March 28, 2014 for Model Number FPHS2687KF0 WHERE IS THIS MAIN CONTROL BOARD LOCATED. THE PARTS DIAGRAM IS LOUSY! PART NUMBER 5303918498
1 Answer To access the main control board you would need to remove the kickplate at the bottom of the unit. With the kickplate removed you will then look under the unit on the left side opening and the control board is in the gray box that is held by one 1/4" screw. Read More...
Glenn November 29, 2013 for Model Number LPHS2687KF0 Subject : Frigidaire Refrigerator LPHS2687KF0 This issue started with a SY CE message identified as a communication error by your site and others. When unplugged and plugged back in it would try to start then would trip a relay on the switch board. Eventually shutting down completely displaying the CE. I ordered a P/N 5303918498 from you to replace the original P/N 242000406. I swapped them out and now I get nothing at all. It goes back to the original failure when I re-install the original board. If the problem was something other than the board I would have expected a duplicated error. Any thoughts?
1 Answer Hello Glenn. It sounds like you need to check the wiring and make sure it is good. Also, you may need to replace both the dispenser and main board in the unit. This is a suggestion from the manufacturer for the error code provided. Read More...
Dawn C September 13, 2013 for Model Number LGHS2667KE0 The auto-frost is not working. Ordered a new board switch (part #242000406 - which is a replacement for part #5303918498), when installed the fridge doesn't power on. If I put my old board back in, then it powers on just fine. Tech thought we could have gotten a bad board so we ordered another one. After installing the second board, the fridge still does not power on. When I put my board back in, it powers on just fine. Two techs say we have the correct board and have no other ideas on why these new boards will not work. Any suggestions? The fridge is only 3 years old:(
1 Answer Dawn, It may be possible that the board was mispackaged at the warehouse and you would want to get another one. Also see if the original harness will connect directly to the board. Read More...