Rick K January 12, 2014 for Model Number FGHD2433kf1 I can't get the DW to run any wash cycle. It fills with water then pumps out. The following code then flashes, "washing drying Er clean S". The water pumps out but the pump will not shut off unless power is cut off. HELP!!!!
1 Answer Rick, The ER error is an indication of a membrane switch failure. The main control board has detected a stuck key or a key pressed for more than 1 minute. Check the connection from the keypad to the main control board. If correct then replace the keypad 154791806 and if the error continues then replace the main control board 5304514670. Read More...
Dave November 25, 2013 for Model Number FGHD2433KF1 After setting cycle and closing door, dishwasher begins to run but in the display it flashes inconsistant temps (48-89-49-88..) then as it cycles to clean the display flashes "washing/drying Er clean/S" several seconds later the dishwasher stops. Clicked off breaker for a few and restarted, same thing happens. Is my keypad bad or is it the control board? Thanks,Dave
1 Answer Hello Dave. Check the ribbon cable connection and if it is good, replace the control panel on the unit. Read More...
Steve C. November 22, 2013 for Model Number Fghd2433kf1 I am getting power to the dishwasher, but the control panel is not responsive and the indicator LED is not on. What parts should I try and replacing and how difficult is that to do myself?
1 Answer Hello Steve, If you are getting 120Vac to the control board 5304514670 and nothing coming back out of it, it is a safe bet that it has failed. The hardest thing about this job is making sure the gasket is properly placed so no moisture can get into the control board mounting area. This is not a difficult job and you should have no problem. Read More...
Laura S October 14, 2013 for Model Number frigidaire dishwasher model FDHG2433KF1 We have a frigidaire dishwasher model FDHG2433KF1. We had to turn the breaker off to the dishwasher because it would not stop running. When we switch it back on it says PF, we open and shut, and the red indicator light come on by energy saver and air dry. The digital displays says 99. Nothing else will respond on the touch pad. Do we need a new control panel? We have alread replaced the circulation pump.
1 Answer Laura, Based on the information it sounds like the issue would be a faulty control board. The control board is what allows the unit to run and the keypad is just used for setting the controls. With having the unit continuously running it sounds like the control board is the issue. Read More...
Jeff September 06, 2013 for Model Number Fghd2433kf1 Dran pump runs as soon as you shut the door. It runs all the time even if we push any buttons. It started to run after the dishes were washed and we closed the door after we emptied the dishwasher
1 Answer Jeff, If the drain pump is continuously running you will first want to check the wiring from the control board to the drain pump. If the wiring is ok then you will want to replace the control board. Read More...
Kyle August 25, 2013 for Model Number FGHD2433KF1 I cannot get any of the buttons to work. My wife was cleaning the inside as it was all moldy. When we went to restart, it would not work. I turned off the power and it flashed PF and two of the top lights were flashing. I closed the door and PF stopped flashing, but still not able to press any of the buttons to run it. Do I need to replace the control panel or the computer chip?
1 Answer Hello Kyle. Based on the information you provided, you will need to order and replace the console 154791806 on the unit. Read More...
Roy July 10, 2013 for Model Number FGHD2433KF0 We had an electrical storm the other night and power surge in our home. Our dishwasher started automatically and now keeps running. Even with selecting various wash functions the unit continues to run at the end of each cycle. I am looking at the control board replacement as the most probable fix. Thoughts-advice?
1 Answer Hello Roy. Yes, based on the information you provided, it sounds like the control board 5304514670 will need to be replaced. Read More...
Tony November 03, 2012 for Model Number FGHD2433kF0 Close door will not turn off. Will run but makes noise. When wash is complete will not stop.
1 Answer Tony, The console may be a good place to start, but the issue with the "close door" would be due to a faulty door switch 5304525218 or control board 5304514670 or wiring. A fsulty control board, could be the cause of your noise and no shut off issues as well. We'll send you some information, so you can conduct tests using the control panel, and determine your issue. Read More...
1 Answer Hello Barsoum. The console 154791806 does have the membrane with the buttons to select the cycles. However, it does not have the control board or the door switches. Read More...
Todd B. October 22, 2012 for Model Number fghd2433kf1 All the touch pads on the control panel work and it displays correctly, but when delayed start or start pads are touched, nothing happens then the display turns off. Is this the touchpad or the control board? Thank you!
1 Answer Hello Todd, This model has had issues with both the control 5304514670 and the user interface 154791806. I would recommend to check the connections from one to the other by removing the connector and reconnecting, While you have the connector off, look a the pins on the control board that the ribbon cable connect to. If there are any signs of moisture damage, replace both. You will also need to replace the gasket 154478901 around the board since the dry cycle moisture is what generally gets into this assembly. Be aware that if the "console" touchpad has an issue and you connect it to a new control board, the new board will most likely be damaged. Read More...