John January 26, 2022 for Model Number drsyedparvez@gmail.com I am getting error code F2E1 what parts I need
1 Answer John, To be able to assist with what error code F2E1 represents, we will need to have the model number of the product that this code is showing up on. Please resubmit your question with the model number. Read More...
Michael February 18, 2019 for Model Number FEFL77ABA getting F1 code and stove overheats. Have to turnoff breaker. Do i need new oven control board? do I have to order overlay,too?
1 Answer Michael, you are getting a high heat error code, you have either a failed oven sensor or main control. You can check the oven control for resistance, it should read 1080 ohms at room temperature. The overlay on the control can be re-used, although some times in removing it from the old board, some of the paint will peel off. control is 316207527 Read More...
1 Answer Hello Adelita, the ribbon cable would be the part that connects the touch pad to the control board. The overlay is just a sticker that goes over the control which does not have a touch pad. Hope this helps! Read More...
Mari-Ann B. June 02, 2018 for Model Number GAS182G2A1 The letters are wearing off the stove top. Can I get a new set to put on so I know which burner is operating without turning the stove on? These are the letters just to the right of the knobs.
1 Answer Hello Mari-Ann, For a proper diagnosis, we would need you to please verify the model number from the units' I.D. tag since it comes up as a room air conditioner. Thank you for your patience and understanding in this matter. Read More...
Ray January 30, 2018 Why don't you show the back of this part to see if the connection is the same as mine?
1 Answer Sorry Ray. We are adding new videos and photos to our site daily. We do not have one of the back of the part in question at this time. Thank you. Read More...
Aaron November 09, 2017 for Model Number FGGF3054MFG My control board stopped responding when pushing buttons but displayed no error code . I bought a replacement part, #316560118, took the old part off, and put the new one in and have a similar issue. The clock comes on, but nothing happens when I push any buttons! No error code displayed yet again. I have tried multiple times cycling the power. No good.
1 Answer Hello Aaron. Make sure the ribbon cable is plugged into the board good and the overlay is installed properly onto the new clock assembly. Thank you. Read More...
Gregory Mendoza November 07, 2017 for Model Number model # 790.95683301 , ser # VF 33132163, Kenmore electric stove Can I use the control board you have labeled for frigidaire? it looks like a similar - exact one
1 Answer Hello Gregory, we show the correct board for the model number supplied comes up as part number 316207511; you'll also want to order overlay part number 316220805. Thanks! Read More...
Joan August 04, 2017 for Model Number GLEFS77CBB Is there a trick to correctly applying the overlay over the oven control board? Is there a film over the top of it that I need to take off? It's some what bubbly and therefore not perfectly smooth.
1 Answer Hello Joan. Yes, most do have a protective film which will need to be removed. Thank you. Read More...
Dan June 26, 2017 for Model Number FGEG3042KFH The display screen on my Frigidaire Electric Range has slid down and the buttons are not properly aligned. There are four oblong slots at the top of the display that are now visable that were not before. How do I reposition the display upwards to its previous position?
1 Answer Hello Dan. You will pull out the range and remove the back access panel to access the board and reposition it. Read More...
George M February 27, 2017 for Model Number kenmore #316207502 is the oven control for the Frigidaire shown the same as the one that will fit my Kenmore oven I used the part number on my Kenmore paperwork
1 Answer Hello George. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...