Patrick October 29, 2013 for Model Number pld4375rfc3 ER code flashes along with S and several other lights. Key pad goes back and forth between normal, rinse and ultimate scrub. Eventually starts running but does not wash and then shuts back off.
Jim August 25, 2013 for Model Number Frigidaire PLD4375RFC dishwasher The ER code along with the normal wash and rinse button flash simultaneously. After turning off the power the PF along with two other buttons flash for about a minute and then the ER code comes back on and the unit runs continuously but doesn't wash, with no response to the buttons. Please advise.
1 Answer Jim, Based on the information provided it sounds like the control panel could possibly have a stick key which would require replacement of the control panel. Read More...
Tasha March 19, 2013 for Model Number pld4375rfc2 My Frigidaire dishwasher stops mid cycle and blinks Er washing drying clean S. It just flashes that continuously and doesn't finish the cycle. I have no idea what is wrong or what part if any i need to order. Any info would be greatly appreciated. Thank you
1 Answer Tasha, The Er indicates that there is a membrane switch failure. You will need to replace the membrane switch 154639207. Read More...
Gabie November 26, 2012 for Model Number PLD4375RFC3 My dish washer stopped workng and I saw the letters PF which I believe means power failure. What do think contributed to this?
1 Answer Hello Gabie. It could have been a flicker of the power. If the issue continues, you will need to replace the control board in the unit. Read More...
Maureen November 06, 2012 for Model Number pld4375rfco When purchasing the console assembly, does it come with directions to install it?
1 Answer Hello Maureene. No, but it is not real hard to install. Remove the inner door liner and make sure the power is disconnected. From that point, you can access and remove the control panel and the screws securing it to the unit. Read More...
Maureen November 05, 2012 for Model Number PLD4375RFCO while running my dishwasher, it stopped mid wash with a ER flashing on the panel. I unplugged it, then plugged it in again and it flashed a PF (I figured the power failure was from unplugging). when it didnt stop flashing this, I closed the door to the dishwasher and the panel went blank-now none of the bttons work and the panel doesnt light up at all.
1 Answer Hello Maureen. Based on the information you provided, it sounds like the console 154639207 is bad and will need to be replaced on the unit. Read More...
Jim October 22, 2012 for Model Number PLD4375RFC0 On my Frigidaire dishwasher, # PLD4375RFC0, I got the ERR message, nothing worked. I replaced the console panel and the unit worked fine. I noticed after the first wash that the left side top of the console panel was wet and replaced the gasket. I believe that the first console panel failed because it was damaged on the left side top. My problem is there is still water coming out on the new console panel. The door latch seems to work OK. Do I need new door springs to close the door tighter or might it be that the tub is not aligned with the door?
1 Answer Hi. Just making sure that you have the control board gasket part # 154478901. Feel the inside of the inner door part # 5304460897 to see if it will seal fine or if it is warped and not sealing. Does the hinges, Lt. part # 5304513274 Rt. part # 154597701 make any noise or jump out of the pivot points when closing. If there is no smooth action then replace the hinges on each side. Remove the lower rack. Use a torpedo level on int the tub where the rack rolls on to see if the tub is level front to back and side to side. All 4 - legs have to touch the floor so the unit does not twist and misaligned the door latch during heated wash especially. Thank you. Read More...
Jim September 28, 2012 for Model Number PLD4375RFC0 I had the "err", flashing buttons, etc and replaced the console assembly and the dishwasher works great. After the first wash, I noticed the top right side of the button pad was wet, and that was the same area of the malfunctioning pad that I replaced. The old pad was warped and had lifted up and I think that water damage may have caused this damage and the pad's failure. I noticed that the inside rim gasket had some white mineral deposits on it and rubbed them off. I have not done a second load of dishes yet, but I am wondering if I should replace the gasket with AP5319072. The gasket does not look damaged otherwise and door seems to latch correctly.
1 Answer Hello Jim. Based on the information you provided, it sounds like the gasket 154827601 will need to be replaced in the unit. Read More...
Chris September 07, 2012 for Model Number pld4375rfc2 My dishwasher started to have problems and gave an error message. After a few days waiting for a repairman the dishwasher started to work again but only speed clean. Sometimes it stopped working and if we waited 2-3 days it would work again but only on speed clean. Then speed clean stopped working and only the normal wash cycle worked. This was ok for a couple of months, but last night the dishwaser stopped working and no lights or cycle can be selected. I powered down and up. I get the power failure error but when reset no lights or ability to select a wash cycle. I am not sure if I should replace the console or control board.
1 Answer Hello Chris. Based on the information you provided, it sounds like the control panel 154639207 is bad and needs to be replaced. Read More...
Ric February 15, 2012 for Model Number PLD4375RFC0 Thank you for the response to my "Er error" question suggesting to replace the control board AP4499574.You suggest to check if the console assembly AP4298713 is working properly. How do you suggest to do that? Do you have a wiring diagram that I can use to check continuity from? Thanks again
1 Answer Hello Ric. There should be a tech sheet located on the unit that will have all the procedures to test the control panel 154639207 on the unit. Hope this helps. Read More...