Nelson March 13, 2017 for Model Number GFSS6KKYCSS GE factory says I need two mother boards to get my ice-maker to work. My GE model was made by Samsung.
1 Answer Hello Nelson, The main board for this unit is WR55X10985. This is the only board on model GFSS6KKYCSS that the icemaker is dependent on for normal operation. Read More...
Beaty March 09, 2017 My ice maker in my GE profile (French door style with drawer freezer) makes a knocking noise every couple of hours or so. Is this because it's not getting enough water to make the ice?
1 Answer Beaty, This would most likely be an issue where the icemaker heater is not coming on to eject the ice. You will want to check at the control board when the icemaker cycles to make sure that there is 120 vac to the heater. If there is then this would likely be a faulty icemaker. If no power then the control board would be the issue. Read More...
Dave March 02, 2017 for Model Number PFSS6PKWBSS Since replacing the ice maker a couple years ago the ice maker will not quit making ice. Should I replace it again? The original problem was it quit making ice all together.
1 Answer Dave, The icemaker would not need to be replaced but would recommend replacing the feeler arm with part number WR49X10103. Read More...
Deb February 18, 2017 Just replaced my ice maker and now water keeps leaking the ice freezes and will not dispense plus it makes a knocking sound.
1 Answer Deb, This issue sounds as though the water valve is not fully shutting off which would put too much water into the icemaker and will cause it to be harder for the ice to eject. If this was not occuring prior to the icemaker replacement then this would be an issue with the new icemaker or the water valve is needing replaced. Read More...
M August 20, 2016 for Model Number PFSS6PKWBSS The ice maker on my GE profile refrigerator started to make clicking noise non-stop, when I put my hand on the ice making unit I can feel some vibration along with the click noise. it sounds more like hitting a glass table with a quarter once per second. When I turn off the ice-making function the clicking stops. But I do see ice on the ice tray. any suggestions? thanks.
1 Answer M. This issue would be caused by a faulty icemaker assembly which would need replaced and the part number for the icemaker assembly is WR30X10097. Read More...
Leann June 21, 2016 for Model Number PFSS6PKXESS My FRIDGE is french door style i don't know how to get the old ice maker out to replace it
1 Answer Hello LeAnn. To remove the icemaker: 1. Remove the Ice bucket. 2. Remove the Phillips-head screw that attaches the front of the wire harness cover. 3. Using a small flat blade screwdriver, pry the front of the cover out, then pull the cover towards the front of the refrigerator. 4. Note the routing of the icemaker wire harness, then disconnect the harness. 5. Push in the release tab on the front of the icemaker, then pull the icemaker out of the ice room. Note: When installing icemaker, engage key slots in key tabs before pushing icemaker in place. Read More...
Angela April 18, 2016 for Model Number GE Profile PFSS6PKW Pieces of the ice bucket assembly are breaking and dropping through the ice dispenser on our GE Profile PFSS6PKW. Is AP4485196 the correct part to replace this assembly? Is just the bucket not available?
Don Z. January 02, 2016 for Model Number Model PFSS6PKXBSS I recently had problems with the ice maker and thanks to your website was able to determine I needed to replace it. However, now that it has been replaced I have discovered small amounts of water accumulate under the deli pull out tray, as well as inside the deli tray on occasion. I have looked for signs of where the water may be coming from and can't seem to locate any leaks. Any ideas?
1 Answer Hello Don. The drain is clogged on the unit. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. http://forum.appliancepartspros.com/refrigerator-freezer-repair/173916-kenmore-top-mount-refrig-h2o-build-up.html Read More...
Randy October 11, 2015 Icemaker makes plenty of ice but does not shut off when arm is up and continues to make ice. Is there an adjustment for the arm?
1 Answer Hello Randy, I'm sorry but the arm on this icemaker has no adjustment. If you provided the units' Model number from its' I.D. tag, we could give a more detailed diagnosis. Read More...
Russ September 16, 2015 for Model Number Pfss6pkxass Just put in new ice maker. The ice arm is up and does not lower. How long before ice is made