Customer Questions and Answers for Orifice Spud by Ge

Greg, When you say gas does not flow, have you tried turning on the burner and lighting it with a match or lighter? If you turn the valve on and that burner does spark like it is designed to do then I would remove the orifice and see if gas flows. The only reason a orifice would cause this is if it were clogged with debris. I believe you will have a valve issue. If the burner doesn't spark then probably the switch harness is the problem. WB18X31210

Tiffany, the 1.5mm orifice WB28K10022 is going to be the left front and rear, the 1.68mm orifice WB28K10030 is for the right front, and the 1.07mm orifice WB28K10029 is going to be for the right rear on your model.

Tom, to convert back to natural gas the orifice assemblies would be needed as the NG orifices are not listed as separately available. They assemblies are as follows: Left front [WB28X20607], left rear [WB28X21953], center [WB28X21513], right rear [WB28X21954], and right front [WB28K10812], the gas valve [WB21X21506] and the broil tube [WB28X20389] would also need to be replaced for the NG orifice

George, You would need to get 4 orifices WB28K10023, for the top burners. The oven you would tighten the orifices to snug and open the air shutters all the way. Flip brass cap on the regulator from NAT to LP.

Hello Rashaad, according to the model number you'll need the following orifices. You'll need a quantity of 1 WB28K10834 for the right rear, both left burners use part number WB28K10023 and the right front uses part number WB28K10032. Hope this helps!

Hello Greg, You will need to order the orifice holders to obtain the natural gas orifices WB28K10786, WB28K10735, WB28K10736, WB28K10389, and WB28K10737. You will not need to replace the complete tube assemblies but you can remove the orifices and install them in the correct locations. Be sure to do this one at a time, making sure they are installed in the correct locations. You will also need to convert the regulator by removing the cap and removing the center nut. This will be flipped over and the cap installed in the opposite fashion than it is now. You will then need to adjust the orifice hoods for the bake and broil by turning them 1 1/2 to 2 turns counterclockwise and adjust the yellow tipping from the flames by adjusting the air shutters.

Hello Jason! The manufacturer doesn't offer the orifices separate from the gas tubes. You'll need to order part number WB28K10191, WB28K10192, WB28K10190 and WB28K10188. You'll have to flip the cap on the pressure regulator WB19K10044 to NG and turn the orifice mounted on the valve 2 1/2 turns counter-clock wise and adjust until you get a blue flame. Hope this helps!

Jon, The part number for the orifice spuds would be left rear WB28K10023, Front left and right rear WB28K10022, and right front WB28K10029. For the oven you will loosen the orifices 1 1/2 to 2 turns and close air shutters to about 3/4 of the way open. Also flip the cap on the regulator from LP to Nat.

Johnny, You will need the following orifices to convert this unit to natural gas, for right front 1 of WB28K10694, 3 of WB28K10693, for center WB28K10871, Front left WB28K10740, left rear WB28K10475, and right rear WB28K10741. For the oven you would need dual cavity elbow WB28K10738, upper bake elbow WB28K10706, and lower bake elbow WB28K10708.

Hello Dave. You will need to order WB28K10596, WB28K10424, WB28K10590, WB28K10592, and WB28K10390.