Sandy September 13, 2014 for Model Number RGA720EK3WH I need to convert this stove from natural gas to LP...which orfices do I need?
1 Answer Sandy, you'll need four LP orifices part number WB28K10376. Flip the cap on the regulator and adjust the oven orifices. Thanks. Read More...
Chris August 19, 2014 for Model Number JGBP26CEH4CC My GE range is set up to burn propane right now, and I need to convert it to burn natural gas in my new location. Is it true that all I need is four natural gas orifices WB28K10033, two oven orifices WB28K202 (one for the oven and one for the clean mode orifice) and to reset the regulator to NG? Also, I was told that the 4 stove orifices are different? Well three orifices are the same and one is different? I found this orifice WB28K10033 but not sure what the other ones are? Thanks so much! Chris Model Number JGBP26CEH4CC
1 Answer Chris, You will need to get the bake orifice spud WB28K202, the broil orifice WB28K10310, the orifice part number WB28K10033 (should need 3 of these) and orifice part number WB36K10619. And then you would flip the regulator. Read More...
Mark January 18, 2014 for Model Number MGC553BDS Im looking for NG spuds my cook top has LP spuds now and I would like to convert back to NG. Thanks Mark
1 Answer Mark, To convert the unit back to natural gas you will need the following parts. Orifice holder for the Left rear 9.2K WP74007691, orifice holder for center 5K WP7527P023-60, orifice holder Right front 12.5K WP7527P028-60 and orifice holder for left front and right rear 9.5K WP7527P026-60. You would also need to flip the cap on the regulator from LP to natural. Read More...
R.S. October 31, 2013 for Model Number JGBS03PPA1WH I'm looking for high altitude orifices for this Range running on LP gas. Thank You.
1 Answer Hello! The manufacturer does not offer high altitude orifices for your appliance. If you need to convert your range you'll need four LP orifices part number WB28K10376. Adjust the air shutters on your unit. Thanks. Read More...
Phil October 21, 2013 for Model Number JGBS07PEH2WW My GE range is set up to burn propane right now, and I need to convert it to burn natural gas in my new location. Is it true that all I need is four natural gas orifices and to reset the regulator to NG? Also, where IS the regulator on the unit? Thanks so much! Phil
1 Answer Hello Phil! Yes, you'll need four NG orifices part number WB28K10033. Flip the cap on the regulator back to NG. The regulator is on the back on the appliance towards the bottom. Adjust the oven orifice two full rounds ccw and adjust the burner flame until its blue. Hope this helps. Read More...
Angie June 23, 2013 for Model Number 362.7132191 What is the difference between a oven orifice and the top burner orifice?
1 Answer Hello Angie. They are different in design. Top orifices are smaller than the oven. Read More...
1 Answer Dale, you'll need to purchase the NG orifices part number WB28K7. The following link is to your owners manual, refer to pages 40-44 for the conversion instructions. Hope this helps! http://www.geappliances.com/search/older-pdfs/49-8542.PDF Read More...
Pt February 23, 2013 for Model Number GE XL44 JGBC20WEA1WW The range has 4 burners of 9000 BTU each. I would like to raise the burners (2) to 12,000 BTU or higher possible. Can it be done and how? Thanks
1 Answer Hello PT. No, the unit is set up for 9,000. If you want larger, you will need to replace the unit. This is dangerous to try to change a gas product when the manufacture builds it to certain specs. Read More...
Chris C January 26, 2013 for Model Number Kenmore range model 66572029100 Hi, I just purchased a used Kenmore range/oven that was used with LP propane and I have gas natural gas at my location. So far I have flipped the regulator and changed it to natutal gas can someone please give me the 4 part #s I need for the 4 stove top burner orfices I need to replace?
1 Answer Hello Chris, The part numbers for the orifices are as follows: 8273063Left front WP8273065 quantity 2 WP8273067 quantity 1 Read More...
Al June 04, 2012 What is the orifice/ hole diameter for this item p/n AP3994353? Also,what is the thread size?
1 Answer Hello Al. Sorry, but we do not have that information available. You can contact the manufacture and see if they are able to provide you the hose size in the orifice. Read More...