Virgil October 11, 2019 for Model Number wcsr2090g9ww Are the load size selector (small, large, super) and the water pressure switch the same thing?
1 Answer Virgil, the pressure switch WH12X10378 would indeed also be the load size selector for this model. Read More...
Clint October 05, 2019 for Model Number 110.21302012 Water is leaking from the bottom of our Kenmore washer. It is model no 110.21302012. I believe the pressure switch needs to be replaced. Do you have one for our Kenmore model?
1 Answer Hello Clint, the pressure switch for this model is part of the control part number W10480184. You might want to verify where the leak is coming from, thanks! Read More...
Ana June 07, 2019 for Model Number GTWN4250D1WS Wmachine wont fill enough water (very little) when is going to rinse (the second part in any cycle chosen) What could be the pressure switch or the water inlet valve? Thank you for your assistance with this matter.
1 Answer Hello Ana, you'll want to check the water valve fill screens (especially the cold water connection.) If all looks good you might have to replace the water valve since the issue could just be the cold side of the valve. Hope this helps! Read More...
Rc March 02, 2019 for Model Number WMSR311OWOWW washer goes into spin cycle, starts to spin then immediately turns off. Pump is still running draining water, but won't spin.
1 Answer RC, You will want to check to make sure that the pressure hose is not clogged. If the unit pressure switch does not reset to the empty then it will cause the unit to not spin. Also check the lid switch to make sure that it is good. Read More...
Debi December 02, 2018 for Model Number glwn2800dows I bought the pressure switch for you awhile back and it fell and I cant get in back into place. Does it clip to the panel itself?
1 Answer Debi, The pressure switch has 2 metal hooks on it next to the shaft that you put into the bracket and then rotate the pressure switch to lock it in place. Read More...
Joyce June 03, 2017 for Model Number GHWN4250D1WW My GE Hydro wave will not fill completely. I can only wash two or three pairs of blue jeans in a load and I always have the machine set for second rinse or the items do not come clean. Can we adjust something on the machine to allow for more water? We replaced the pressure switch thinking the other was bad but this did not help. Thanks
1 Answer Hello Joyce, I'm sorry but this machine is considered a high efficiency machine so water conservation has been designed into the machine. There is, unfortunately, no way to change this characteristic without redesigning the machine. Read More...
Dianne E November 18, 2016 for Model Number WSLP1500J0WW I have a GE portable washer that I connect to my kitchen sink. The water fills for the wash cycle, but does not fill for the rinse cycle. I am getting the FF error which means Failed to Fill correct? Why would it fill for the wash but not for the rinse? What part do you think needs replacing? Thank you,
1 Answer Dianne, The parts that would cause this unit to stop would be either a bad Main control board, pressure switch or water valve. With this doing this on rinse it would be more likely that the control board is the issue. Read More...
Sandra J February 12, 2016 for Model Number WBSR3140G2WW I have a GE washer and the plastic teeth that surrounds the timer shaft are worn so that the timer knob does not turn properly. Can the teeth be replaced?
1 Answer Sandra, The part number that you will need for the issue with the knob not engaging to turn the skirt on the timer would be the timer knob part number WH01X10310. Read More...
Bullyman July 28, 2014 for Model Number VBXR1090DBWW Replacing Pressure switch the replacement part AP4358796 looks alittle different from the one i removed from the machine it doesn't have that metal piece at the end that curves like the replacement does. will the replacement still work? Also does it come with a tube? if not what is the replacement tube part number?
1 Answer Bullyman, Yes, even with the curved bracket the pressure switch will still work for your unit. The switch does not come with the pressure hose and the part number for the hose is WH41X365. Read More...
Jj March 02, 2014 for Model Number WHDSR109J8WW Hello, I have a problem with washing machine not spinning, machine fills as normal, agitates thru wash cycle, pumps water out but doesn't spin. I removed front cover to observe motor, the Belt is intact, but not moving.The water pump continues to run, but machine wont spin. I have reset by unplugging machine and cycled washer lid up and down several times to reset. If the lid switch is faulty, will machine still agitate? I am assuming it won't, so I figure that it must be ok, Same with fill level switch, seems to have correct amount of water when it fills..
1 Answer JJ, You will want to pull the belt off the motor and see if the motor turns without it on. If the motor turns with no belt on then the brake would be seized up causing the issue. If the motor does not turn then you will want to check for voltage to the motor from orange to dk blue. if there is no power then the timer would be the issue if there is power then the motor would be the issue but is not likely the case. Read More...