Lorenzo April 19, 2023 for Model Number WM3470HWA I have a question about this LG washer machine i replace the washer water inlet valve P.N. 5221ER1003A and still water cam in into the washer i replace the washer water level and water still cam in i do not wat else i have to replace thanks in advance
1 Answer Hello Lorenzo, the hot water inlet valve needs to be checked, it is separate from this cold water valve assembly. Read More...
Jerry July 13, 2022 for Model Number LGWM2650HWA Hit the power button & within 1 second the machine powers off. Replaced door switch (AP4998848) & pump (AP5328388), no help. Standing in front looking back, the 3 pack of solenoids on the right (Cold, I think 5220FR2075L) are extremely rusted on top. Not sure what this means or how to test. The single solenoid on the left (Hot, I think) is not rusted.
1 Answer Hello Jerry, the user interface panel is failing, the part EBR36870731 is no longer available from the manufacturer. Read More...
Nayla June 19, 2022 for Model Number kenmore washer washer only dispensing hot water on all settings.
1 Answer Nayla, With the unit only putting hot water into the unit, this would most likely be an issue with the thermistor in which it is reading the temperature wrong. Test the thermistor and if it is good the the main control board will be the issue. Read More...
Wondering Mind March 09, 2022 I have a 5-year old RCA RWD200-B with a leaking water inlet valve. It looks exactly like your AP5986564 water inlet valve assembly. Do you know if the part is compatible with the RWD200-B?
1 Answer Wondering Mind, Unfortunately, we do not have information on this washer to be able to advise if this valve will work for your model. Read More...
Mike O. April 02, 2021 for Model Number Kenmore Washer #41262.610 After washing a load I had a little water leaking and heading in to my floor drain. After removing the rear access panel and then the top I could only find a slight bit of water below the cold water inlet valve. A very small amount. After cleaning up I turned the cold water back on only to see a small amount of water start to appear in the center of the valve between the three solenoids. Turned water of and after a slight clean up I repeated the process and got the leakage again. Ordered the LG 5220FR2075L water inlet valve. This item did not come in a factory sealed box as the repair video shows. Instead it was in a 10" by 10" bubble wrap bag which offers not a whole lot of protection. When I opened the package I noticed that four of the six spade connections for the wire harness were bent downward. I gently straightened them with needle nose pliers and installed the part. Turned water on and no leaks. Started a load of clothes but get no water coming in to the machine. Cycles to wash mode but no water. I will put the old one back in when I get a chance and see if I get water through that one. Otherwise I'm at a loss. Thanks ,Mike
1 Answer Hello Mike, I'm sorry but we will need to ask you to please post a new question including the verified model number from the units' I.D. tag since the one provided will not come up for us as a valid model number. Thank you for your patience and understanding in this matter. Read More...
Larry Shiembob December 20, 2020 for Model Number WM3470HVA I just replaced a burned out inlet water valve on the cold water side that has three solenoids. I now get FE error that indicates overfilling and there is water left in the machine. It seems like the solenoid letting water go to the detergent dispenser does not shut off unless I remove the connector. when I do the machine seems to run normally. Question - how long should water be flowing into the dispenser? If I run with that solenoid disconnected is that a problem (I could put the detergent in the washer.) The solenoid opens and closes when power is turned on and off so if it is staying on does that mean I have a bad control board? Thanks for the help.
1 Answer Larry S, Based on the information provided the solenoid is good if it stops when power is removed and opens when power applied. Based on this it does sound as if the control is applying power incorrectly and would need to be replaced. Read More...
Willis October 31, 2020 for Model Number WM2101HW Runs in cold water no mater what water temp is selected. Hoses are hooked up correct. When water starts flowing in and hot selected it makes no difference if I shut off the hot water faucet, it does however shut off when turning off the cold. If I select cold it makes no difference if I shut off the hot water faucet but will shut off when I shut off the cold water faucet. When warm is selected it the water stops coming in when turning off the cold and leaving on the hot. It keeps coming in when I turn off the hot only ( which makes sense ) Could it be AP5986564 valve or the hot only water inlet valve. What is the operating sequence for these valves?
1 Answer Willis, based on the information provided, it sounds like the main control EBR38163357 is not operating properly and is not sending 120VAC to the hot water valve 5220FR2006H when necessary. This can be tested by turning on a hot water cycle and testing the valve for voltage. If 120VAC is not present, then the control has failed. Unfortunately, the control has been discontinued by the manufacturer and is no longer available. If the valve does receive voltage, then it has failed and would need to be replaced. Read More...
Joe July 06, 2020 for Model Number WM3470HVA My issue has been that the tub of the washer will fill with water when the washer is off, even when it is unplugged as well. I've replaced the hot water inlet valve and I am looking at replacing the cold water valve. Could it be anything else or just the cold water valve?
1 Answer Joe, With the washer filling with the unit in the off position then the cold water valve will be the most likely cause for this issue. Read More...
Ariana June 05, 2020 for Model Number WM3250HWA Watched repair videos on replacing H2O Inlet Valve Assembly (-ies) for LG Washer WM3250HWA, which will make replacing these parts so much easier. But I do have a question. In your video, the repair man took new unit from box and installed it directly into washer. Question: do these inlet valves come with the Inlet Valve Filter Screen already in them (as seen in video)?
1 Answer Hello Ariana, yes, the filter screens are part of and already installed into the inlet water valves. Read More...
Louella May 09, 2020 for Model Number RAL5144BWI I have a Roper washer model# CE4242876, model # RAL5144BWI. Will not fill wit cold water. What could be the problem and what is the cost of the part to replace it?