Tawny April 28, 2024 for Model Number samsung dve52m8650w/a3 One pin/tab on the side of the lint trap cover on my Samsung dve52m8650w/a3 dryer broke. I can't find a replacement anywhere as it seems the part is discontinued. Is there another cover that will fit? Can I use it without the cover? Thank you in advance.
Daniela July 05, 2022 for Model Number DVE45R6100C/A3 I need the lint filter cover but I can’t find it anywhere. This one says is not compatible with my model, DVE45R6100C/A3 do you happen to have it ? I can’t find it
Jimmy September 23, 2021 for Model Number DVE45R6100W/A3 Thank you for your reply. You still didn't answer my question: how do you remove the front filter assembly in order to connect the two pieces together. You said they should snap together w/ 2 pieces. You have to remove the front filter section first & snap in place with the rear .
1 Answer The entire filter cover assembly would be removed by unscrewing two mounting screws, one located at each corner. This will allow access to the locking tabs of the assembly. Read More...
Jimmy September 23, 2021 for Model Number DVE45R6100W/A3 The dryer filter cover,DC63-01140A was replaced after prying off the 2 sections of the dryer filter assembly. The problem is how do you get these 2 pieces connect together. The back part is detached from the front part.
1 Answer Jimmy, the two cover assembly housing parts would snap together using locking tabs that line up specifically to each part. If these tabs have broken, the cover assembly DC97-16160A would need to be replaced. Read More...
Kristina April 29, 2020 for Model Number DVG55M9600W MY COVER FILTER DC63-01140A needs to be replaced and I can't find one. The tab broke. When i tried to order the message said it will not fit my dryer model DVG55M9600W. What do I need to do? I would like the part.
1 Answer Hello Kristina, according to the manufacturer , the cover part DVG55M9600W DC63-01140A, will fit your model dryer. Read More...
Dn September 19, 2019 for Model Number dv405 samsung dryer Is the Samsung DC63-01144A COVER-FILTER(U);BIG-BANG DRY really needed? The plastic end where the spring goes on mine broke, but I don't really see that I need the cover. Would like your opinion. Thank you.
1 Answer DN, The purpose behind the door inside the lint cover would be so that it will help to prevent some of the lint from falling down into the duct. It will also help to keep the lint screen from getting pulled up by clothing as it goes past. It is not necessary to replace it but would be a good idea to do so. Read More...
1 Answer Karen, You'll probably find it easier to remove the filter grill/cover from inside the drum/bulkhead(3 screws) manipulate and remove the assembly, and disconnect the sensor bar wires from the terminals, if equipped. Separate the front grill from the rear housing. The door and spring are mounted to the rear housing. Slip the center opening of the spring over the right side "peg" on the door, " flex" the door to insert the pegs into the openings of the housing, Position the spring with the straight end facing down and against the rear housing, and the bent/twisted end against the bottom side of the door/cover, so the door "flips" and sets up/closed . reverse the removal procedure and check the door and dryer operation. Read More...
Robert K April 08, 2018 for Model Number DV42H5200GW/A3-0000 How do I install the Lint Filter Cover and spring. I can't see how to install the spring and the lint filter cover. The spring is missing on mine and the tab on the lint filter cover is broken. What do I need to do to install these two parts and how do I do it. do you have a video? instructions?
1 Answer Robert, Unfortunately there is not a video for the cover filter assembly. To install the spring it will go on one of the pegs of the cover and will rotate in order to allow the door to close when the lint filter is removed. Read More...
Wayne March 17, 2018 for Model Number DV42H5000EW/A3 We have a Samsung DV42H5000EW/A3 dryer. The cover-filter door on our dryer that closes when the lint filter is removed has a broken tab, and the spring is missing. I need to replace both the door and the spring. Is there a video showing how to replace the cover-fllter door and the spring that closes the door, and what are the proper part numbers for our dryer?
1 Answer Wayne, The spring for this will be part number DC61-02740A and the door is part number DC63-01140A. Unfortunately there is no video for this part. To install this you will need to remove the lint vent on the inside and then you can install the door. Read More...
Matt February 28, 2017 Is there a spring assist part that's needed when installing? I attempted to install the new cover and the end hope tab broke right away, not sure how this would stay shut when removing the filter to clean, might just use my warranty at this point...
1 Answer Matt, There is a spring that would be on the cover assembly that would allow the door to close when the lint filter is removed. We would need to have the model number to provide the spring part number. Read More...