Joe July 11, 2023 for Model Number KDRS505XSS00 Hi. I need to purchase left front burner head as well as the bottom piece which i believe is called orifice holder plus couple of screws that were rusted out. Can you please provide me with the link to those three parts. Thank you.
1 Answer Joe, Parts requested: WPW10406878 Left Front burner head WPW10407678 Left Front, holder WP8273062 screw Read More...
E.P December 13, 2020 for Model Number WFG371LVB1 I believe my burner head needs replacement but I don’t understand how they go bad. My igniter works and I have gas flow but it does not ignite. I switched it with the opposite burner and it doesn’t work in its new location. The side that didn’t work now works. Could you please explain to me how they go bad as my burner does not have a pilot hole. Btw, I’ve taken all burner heads off and thoroughly cleaned them. I did not reinstall them until they were completely dry. Thanks in advance for any and all help on the subject.
1 Answer EP, The sparking does not happen on the burner head itself. This would take place on the burner cap that goes over the burner head. If the cap is rusted on the bottom or dirty on the bottom it will cause the igniter to not spark properly and ignite the burner. Make sure that there is no rust or corrosion on the bottom of the burner head. Read More...
Angel April 15, 2020 for Model Number MGT8775XS03 On the burner head, which screws are they for replacement? Are all of the burner head screws the same one? They look like Torx style head screws.
1 Answer Angel, the Torx screw WP3368921 should work with your model and would be the same for all of the burner heads. Read More...
Kada March 19, 2020 for Model Number GLS3074VS02 Hello, We have a Whrilpool Gas Cooktop. Out of the 4 burners, 2 of them lightup, but for the other 2, only keep hearing a clicking sound. Need to use a match stick to turn them. Please advise on what could be the problem, and the parts I need to order to fix the issue. -Thanks
1 Answer Hello Kada, check the burner's spark electrode for grease/food particles/cracks that may be shorting the spark, if needed the electrode is part WP9782116, if the spark module is weak it is part AP6015060]. Read More...
Debbie May 29, 2019 for Model Number Whirlpool kgrs505xwho4 The burner on the front right of our Range is not turning on it is stuck. What part do I need to fix this? Also I had someone at my house that did not know this and turned the knob to hard and bent the stem under the knob. What is the part for this as well?
1 Answer Debbie, if the valve for the front right is not turning, then the valve [WPW10206288] would need to be replaced. The valve includes the stem that the knob sets onto. Read More...
Tom November 07, 2018 for Model Number JDR8898AAS Left front (big) burner "hisses" after being on 5 or so minutes. Once hot it will not stop doing this, even if you turn it of and turn in back on. Only after it cools down will it light and sound normal, but then it will begin to hiss as soon as it heats up. What do I need to replace? If burner, need screws too as these are rusted. Please provide part numbers of what needs to be replaced to fix this problem. Tom
1 Answer Tom, The model number listed is not coming up as a valid model. Please provide a good model number and resubmit your question so that we can assist properly. Read More...
Willard F September 13, 2018 for Model Number JENN AIR JDR8895AAS From the 5 burners, I need to replace the front right one,(next to the controls) not the larger one, the next in size, and I need the screws also, what are the part number to order them? Willard for Model Number JDR8895AAS ANSWER Willard, The part number for the right front orifice holder will be WP7527P028-60 and if you need the burner head it will be part number WPW10406797. I need also the number on the screws, thanks
Willard September 10, 2018 for Model Number JDR8895AAS From the 5 burners, I need to replace the front right one,(next to the controls) not the larger one, the next in size, and I need the screws also, what are the part number to order them?
1 Answer Willard, The part number for the right front orifice holder will be WP7527P028-60 and if you need the burner head it will be part number WPW10406797. Read More...
David June 21, 2018 for Model Number MGR5775QDB The large right front burner flame does not increase in flame size like it used to. If I start the burner and take off the round top, the flame seems to go up and down just fine. Is it just just the top component?
1 Answer David, The burner cap would not cause the flames to be higher or lower as this is dictated by the gas flow. You will want to check to make sure that the burner head and caps are clean and if they are then this would likely be a burner valve issue. Read More...
Sj Painter January 02, 2015 for Model Number MGT8885XS00 The burner for gas range will not turn on. The knob is stuck in the off position.
1 Answer SJ, you will need to check or replace the burner gas valve WPW10206287 . There are a couple of possibilities, the locking detent in the valve may have failed and the valve stem is "locked" in place. The other and more likely issue is the lubricant/sealant inside the gas valve has "cooked away" and the valve stem has seized to the body of the gas valve and can't be moved. Read More...