Chris December 11, 2019 for Model Number RF262LXST4 The oven temp will only go to about 270 degrees on the digital display, will replacing the control board correct this problem. all else is working. My stove is white and the replacement part is out of stock but the black one is in stock and less expensive...will this one work...I don't mind the color... especially for less money. Thanks Chris
1 Answer Chris, Are the inside temp of your oven and the display the same temp? Possible temp sensor reading the wrong temperature. The correct test for the temp sensor is 1100 ohms at room temp. Any fault codes? Press cancel, cancel, start to enter service mode then press temp arrow keys up to screen 5A to see the last error code.Resistances for the two elements are 24 ohms for the bake and about 16 for the broil. If all these test good then most likely it is your control. Read More...
Deny March 29, 2016 for Model Number Wfe361lvso The oven stopped working and we are unable to open the door after self-clean it shows f1.do you know what its the problem? Thanks.
1 Answer Deny, The F1 error code would be caused by a faulty electronic control board. The part number for the board is W10876180. Read More...
Ashley March 31, 2015 for Model Number WFE361LVB0 Electric oven makes a clicking noise when the oven door is opened and the time is not correct. The stove top works and the oven heated up. Do you have any tips?
1 Answer Hello Ashley, The clicking you hear when the door is opened is the light relay on the control. This is normal and must occur if the light is going to work. If the light doesn't come on, you should check for voltage at the light socket. If voltage is there, either the light socket or the light bulb is defective. You should refer to the owners' manual for the instructions on setting the time on the clock. Its' reference says: "The Clock uses a 12-hour cycle with a.m. and p.m. 1. Check that the oven is off. 2. Press CLOCK. 3. Press TEMP/TIME “+” or “-” arrow pads to set the time of day, including a.m. or p.m. 4. Press CLOCK or START." If the clock can still not be set, the electronic control W10876180 will require replacement. Read More...
Randy December 20, 2014 for Model Number RF272LXTD3 The oven seems to work when it wants. If you turn it on then the oven will heat up but after it goes through the Preheat or you open the oven it seems to stop working and not go back on. Or it will never heat to the temp. Could this be the temp sensor or the control board? Is there away to check the Thermocoupler in the oven?
1 Answer Randy, You can check the oven sensor on the unit to see if it has proper resistance. The resistance should be 1090 ohms at room temp. If the resistance checks ok then the issue will most likely be caused by a faulty control board. Read More...
Diane March 28, 2013 for Model Number Whirlpool RF262LXSB4 First sign of a problem was that the light stayed on saying a burner was still on. That was yesterday. The burners still worked, as well as the oven. The next day, the light was still on saying a burner was on but again burners not on, but burners did not work either, and the oven did not work... seconds later lights out for the whole unit. No clock, no burner on light, no nothing. My dad checked to make sure power was getting to the unit, and also checked to see if the power cord had gone bad. It seems to be computer issues, but I am not the whirlpool repair man. I was thinking of ordering the control panel thing, and it looks like it might pop in and out. but not sure. there were no error codes, and of course, no power when I wanted to do the diagnostics. I mean, i had power, just the unit was dead. I was purchased April 2008
1 Answer Diane, It sounds like you are having 2 different issues. The first issue of the light staying on saying that the element is on, if it is the hot surface indicator light then the issue would be in one of the elements. If it is the cooktop on indicator then problem is in one of the infinite switches. For the control board not operating it would be an issue with the control board assembly which would need to be replaced. To test the infinite switches you would check from P to chassis ground for 120vac. If there is voltage then the switch is bad. On the elements you would check from H to Chassis ground. These connection points are the neutral side and should not have power with the switches in the off position. Read More...
Jenny February 08, 2013 for Model Number wfe361lvs The self cleaning lock came out on the oven... the door is open so it cannot shut. There is an F5 code that comes up. We have tried resetting and unplugging and shutting the breaker off even, nothing has been helpful. Just trying to figure out what part we will need to fix this.
1 Answer Jenny, If the self clean latch assembly has fallen out of the unit, and you're getting an F5 error code, they are related. " F5 - Door and switches do not agree / Door latch not operating" The ERC / Clock is looking for the door latch switches to be in a certain position when the control is in the time of day mode/, bake cycle, or the clean cycle. The ERC/Clock constantly checks the switch circuits to determine what the range should be doing. If there's an issue with the switches or the latch, the clock will display an F5 code. You'll need to slide the range away from the wall and check the latch assembly WPW10107820 on the back of the oven and check the latch WP9761013 on the front of the oven, and the linkage between the two. Read More...
Jan H. March 10, 2012 for Model Number RF272LXTD3 I looked at this part around Christmas and it was cheaper than it is now. How come it has double in price in just 2 months?
1 Answer Hello Jan! Whirlpool has recently gone up on their part prices causing our Whirlpool part prices to rise as well. We also keep up with all major competitors so if you locate this part for a lower price on a major competitor site we do offer price matching. Here is our price match link for you to view, thanks! http://www.appliancepartspros.com/customerservice/orderhelp.aspx Read More...
Selby September 11, 2011 for Model Number wfe361lvb I'm trying to figure out which control panel I will need. The one I have is black.
1 Answer Hello Selby! The black control panel is part number WPW10184060. The matching electronic control with the black face is part number W10876180. Thanks. Read More...
Pete August 07, 2011 for Model Number RF262LXSB2 The main problem is more than what lights are blinking, any button I push will not do anything. I can not turn on any burners or oven nothing works.
1 Answer Hi Pete. After confirming you are getting proper 240 vac to the L1, L2 at the board? Then while pressing bake are you getting the same out of the board at the L 1 and bake relay uotput? If not then you will need clock part # W10876180. Make sure both of the bake and broil elements ohm out to approx. 8-22Ohms. Make sure if you have a oven thermostat that it is closed. All of this should help. Thank you. Read More...
Pete August 06, 2011 for Model Number RF262LXSB3 Power is to the stove, but this Part does not control anything anymore. Just blinks nonsense at me! Will replacing it do the trick?
1 Answer Hello Pete! You've stated that the electronic control is blinking items on the screen. Please verify what is blinking on the screen, this will help determine what needs to be replaced. Thanks! Read More...