Ted June 28, 2016 for Model Number 10658904802 Refrigerator side is freezing food. Have both temperature control set on lowest #1 and refrigerator is still about 25F. (Note freezer side is about -10F). Everything else appears to be working, defrost cycle, ice maker, lights etc.
1 Answer Ted, You want to check and make sure the doors close and seal properly, Check the shelves to make sure there are no articles hanging over the edges or against the walls, make sure there's nothing larger or bulky on the top shelf, left hand corner. All of this This could block or redirect the air flow and cause the refrigerator to get too cold. Lastly, carefully lower the control panel and check the control slide and linkage back to the air damper WPW10151374 and make sure the damper opens and closes properly. Read More...
Cycler45 March 13, 2016 for Model Number whirlpool GS6NBE/GF6NFE Having a problem with my ice/water dispenser: When I open the door I get water and ice coming out of the dispenser until I close the door and then the water and ice stops. Is there a module that needs to be replaced in the dispenser?
1 Answer Cycler45, The most likely cause for the dispenser to turn on by itself when opening the door then the first thing to check would be the wiring at the door hinge. Look for damaged or loose connections. If this checks ok then the issue will be with the control board in the dispenser part number WP2303843. Read More...
Donehs5 March 12, 2016 for Model Number Kenmore Elite Cold Spot Model #106.55609400 Currently, there is no ice being made. For the freezer door's IR port, when the door is opened, the light flashes 2 quick flashes then stops. There is a pause, then it flashes the 2 falsh sequence again, then stops. I've troubleshooted the related hardware and there is water supply, but no ice being made. Could the ice level control boards be faulty and need to be replaced?
1 Answer Donehs5, With the light flashing 2 times then the issue will most likely be the emitter board that has failed. Read More...
Robert March 03, 2016 for Model Number GD5RHAXNQOO Are circuit boards such as W10757851 for ice maker warrantied for 365 days just like a mechanical part?
David February 17, 2016 for Model Number GS5VHAXWY00 The part shown for me to order does not match the color of the one in my freezer. Mine is green the one shown is white. Mine has two screws. The manufacturers' number is w10757851 and your number is ap5956767.
1 Answer Hello David, The color of the part W11629974 normally denotes an engineering change and will be a better configuration that the original part. Read More...
Scot A January 04, 2016 for Model Number Ksc24c8eyy02 My in door ice maker is not working. I see no light emitting from the ice level shutoff device when the door is open. No flashing light or any light. No water in ice maker tray. Is it the emitter boards?
1 Answer Scot, If there is no light on the emitter board then yes it would be a faulty board that needs to be replaced. Read More...
David M October 22, 2015 for Model Number KSBS25INWH00 The optics tests OK. Do the emitter boards control the AC voltage to the icemaker?
1 Answer Hello David. If the emmiter board are good, and the temp is 0 to 5° and the icemaker does not cycle, you will need to order and replace the icemaker in the unit. The emmiter boards are used to turn the icemaker off when the bucket is full. Read More...
Dennis September 16, 2015 for Model Number GD25DIXHW00 The ice maker does not shut off. It continues to make ice cubes. I do not see any lights in the sensors. Could this be the problem?
1 Answer Hello Dennis. If the icemaker does not shut off, you will need to order and replace the emmiter kit W11629974 on the unit. Read More...
Chris July 02, 2015 for Model Number 106.56543400 Ice maker does not revive water. The ice maker control switch indicator flashes twice ,and repeats , when the freezer door is open.
1 Answer Hello Chris. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. http://forum.appliancepartspros.com/refrigerator-freezer-repair/29618-ice-maker-not-working-kitchenaid.html Read More...
Mike May 25, 2015 for Model Number GS6NHAXVB03 The control panel on the outsides of the freezer door does not work. It is blank and as far as I can tell none of the controls work. Any thoughts?
1 Answer Hello Mike. Test for power to the control board in the dispenser. If it is there, you will need to order and replace the control board WPW10211153 in the unit. If there is no power, then check the wiring and main board WPW10356040 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...