Zenna S. January 09, 2014 for Model Number Maytag washer model # MAH5500BWW What causes this front loading washer to retain water in the inside after it has run the complete cycle? I can hear the water sloshing around when I manually turn the drum. What part do I need to get this repaired or is this model too old to fool with? Zenna
1 Answer Hello Zenna! This is normal. There is a balance ring with liquid inside to keep the tub balanced. The washer itself is not retaining extra water. Hope this helps you. Read More...
Lee Y October 18, 2013 for Model Number Maytag Neptune MAH4000aww I have replaced the door boot drain gasket, but the cable and spring assembly are a bit of a mystery. I got the cable around the boot but can't figure out how to connect it properly. I have been unable to find a detailed enough diagram to help.
1 Answer Hello Lee. You stretch the spring WP22002099 for the cable and hook the 2 loops at the end of the cable. Read More...
Sabrina September 18, 2013 for Model Number mhw6000xs2 My husband place the boot on closed the door to start the washing machine now the door doesn't open.
1 Answer Sabrina, There should be a green string that looks like weed eater string when you open the dispenser area. If you pull this string then it should release the latch for the door. You will want to check the door gasket to ensure it is properly in place but also check the door lock assembly to make sure that it was reconnected properly. Read More...
Robert M. September 12, 2013 for Model Number mah4000aww I need to replace the boot seal on my Maytag Neptune washer. Please help me with part number and if there are any other parts that would be smart to replace at the same time. Thank You Bob
1 Answer Hello Robert, The door boot for this model is 12002533. There should be no other parts needed for this repair. Read More...
Coleman August 14, 2013 for Model Number Mah5500bww Have a small hole in the bottom portion of bellow. If I order the bellow part will it come with plug and spring wire?
1 Answer Hello Coleman. No, 12002533 is just the door boot w/drain according to the manufacture. Read More...
Jim H July 03, 2013 for Model Number MAH6500AWW I need to replace the door boot drain on my washer. Looking at your website's diagram for my washer number 18 is comprised of a door boot and a plug. However the diagram also shows in close proximity to the boot the following: hose clamp; spring tub; wire boot clamp; hose guard; spring clamp; and door boot drain hose. My question is are all these items included in what is identified as the Door Boot Drain Kit part no. AP4010226? Also, are clear removal and installation instructions provided?
1 Answer Jim, The parts listed do not come with the door boot kit and if just the door boot needs to be replaced then they would not be required to be replaced but you can use the parts that are already on the unit. Read More...
Kelly June 26, 2013 for Model Number MAH5500B The boot seems to get mildue on it. How is the best way to clean it or does it need to be replaced? Thanks Kelly
1 Answer Kelly, The best way to get the mildew off is to clean with bleach water and run a cycle on the hottest wash with bleach. Read More...
Lee May 06, 2013 for Model Number MHW6000XW1 I am looking to order a boot drain kit for my washing machine that model is MHW6000XW1 (Maytag). Please give me an answer for correct part number.
1 Answer Lee, according to your model the door boot seal is part number W11106747. Thanks! Read More...
Samuel May 04, 2013 Please,I am looking for Amana Tandem 7300 spare part for a model #NFW7300WW00. I need the drum (not sure of the name) that keeps the water inside the machine. Also, what is the cost?
1 Answer Samuel, IF you are needing the rubber between the tub and the front panel then you will need the bellow WPW10381562. Read More...
Shea April 19, 2013 for Model Number model#:NFW7200TW serial#:11923692PR I have the model I just mentioned, it is an Amana front load washeri. I am a single mom so I know not much of washer repair, nor what the part is called (sorry). The gray rubber seal around the inside of my washer door has a piece missing. I noticed that it leaks from that area when washing laundry. There looks to be a wire with a spring on it behind the rubber seal. I need to know the part #, and actual name of part, also if its hard to replace so I can order from appliancepartspros. I've ordered before from this company and had EXCELLENT results and OUTSTANDING customer service :-). Thank you in advance, Shea
1 Answer Shea, thats great! I'm glad we can assist you in the time of your parts needs! The large grey gasket is the bellow part number WP34001432. The rear clamp is part number 34001306 and the front clamp is part number WP34001266. You'll need to disconnect the power to the washer and remove the top assembly, control panel and dispenser. Remove the gasket from the front panel inside the door and then remove the front panel off the washer. Once this is removed you'll need to remove the band clamp holding the door gasket to the tub. Reinstall the boot in reverse order. Hope this helps you, let us know if you need anything else. Thank you for your inquiry. Read More...