Ken December 31, 2013 for Model Number Maytag Quiet series 300 dishwasher My door handle has stopped popping back into position. The handle now stays up and will not latch. Is the part AP4264560 the correct replacement? Any other suggestions?
1 Answer Hello Ken. We would need the model to find the correct part. Based on the information you provided, you will need to replace the latch and handle assembly. Thanks. Read More...
Kay December 13, 2013 for Model Number ADB1500AWW My handle is not releasing the lock. I can replace it using door latch assembly AP4264083 correct? However, the door is locked shut. I have no way of getting it open unless I break the handle. I do not have access to any screws. Please advise.
1 Answer Hello Kay. Grasp the location of the handle and lift upward and jerk swiftly and the door will come open to replace the latch assembly on the unit. You need part number W10862259. Read More...
Sm December 02, 2013 for Model Number 587.16182401 I have replaced both the control module and the wiring harness of this dishwasher. It ran one full cycle but now the CLEAN light stays illuminated, even after opening door. As a result, I cannot run the machine again (nothing happens when hitting any other button). While I know the harness is hooked up properly, I am wondering if the two black(left side) / two white wires(right side) that go to the handle are in the wrong order (front to back?) I can confirm that the old wires had the black on the left and white, right... thank you!
1 Answer SM, It sounds like the latch, even though the door is opening that the switches are not engaging showing that the door has opened. Check the switches to make sure that they are good and if necessary replace the latch assembly. Read More...
Gunny November 19, 2013 for Model Number MDB5600AWQ The tabs on the door latch handle broke off. Can I get just the handle itself, or must I order the entire door latch assembly? The apparent mfr p/n is W10130697 for the assembly, no p/n for the handle itself is provided. Thanks for any assist.
Rocky November 18, 2013 for Model Number mbd5601aww 36555222jx Need complete handle, switch. Is the correct number w10130697 my washer is white? My computer skills are very poor. Thanks so much!!!!!!
1 Answer Rocky, the dishwasher door latch and handle assembly is part number WPW10130695. Thanks! Read More...
Jon October 08, 2013 for Model Number mdbh950awb dishwasher I need door latch and handle does part #ap4264559 work in cross reference it says no #ap4481280 is latch only and part # is good, is there a handle part #?
1 Answer Jon, This latch assembly W10862259 includes the handle but looking at reference material it states for models that start MDB would use part number WPW10130695 which also includes the handle. Read More...
Bill July 27, 2013 for Model Number Maytag quiet series 100 I purchased the part w 102715768 but it does not have door handle. Can I take the handle off old switch?
1 Answer Hello Bill. Yes, you can remove and replace the handle, but these are really easy to break when doing so. If it breaks, you will need to order a new handle for the unit. Read More...
Charlewsa920 July 22, 2013 for Model Number mdb5600aws I broke the ears off the (it attaches in 4 places, all broke) plastic handle and need another. Can I get just the handle? If I need the whole latch assembly: Seems there are two possible latch assemblies and mine is 380210 but I think either will do. Can you help?
1 Answer Hello Charles! The handle does not come available separate from the latch assembly. You'll need to order dishwasher door latch assembly part number WPW10130695 for your model MDB5600AWS. Thanks! Read More...
Dave E. June 29, 2013 for Model Number Maytag Admiral Dishwasher DWD1500AWB How do I disassemble the door to put a new door latch on? Simply take all screws off the inside of the door.
1 Answer Dave, That is correct. You would remove the screws on the perimeter of the inner door and lift the door panel up. Once up there would possibly 1 screw holding in the latch assembly in place. Please make sure that the unit is powered off before doing this repair. Read More...
Bill O. June 05, 2013 for Model Number ADB1500AWW I plan to replace the latch assembly (including the handle, latch and switches) for my Amana dish washer. On the original latch the wiring to the switches appears to be molded to the switch. How will I attach the wiring to the new switches? THANKS, BILL
1 Answer Hello Bill, There are only four wires. Two white go on one side and two black go on the other side. The wires are made in molex connectors which will easily come off using a small screwdriver to pry them off. Read More...