Pat May 29, 2013 for Model Number MDB4709AWW3 I came home and my dishwasher had stopped mid-cycle, water still in dishwasher and no power I check to see if the door was closed properly and check the circuit breaker. Nothing!
1 Answer Hello Pat. Based on the information you provided, you will need to order and replace the thermal fuse W10258275 on the unit. Read More...
Tomb May 14, 2013 for Model Number mdbh979awb3 Instructions on new thermal fuse say to cut wires and install new harness. If existing connecting wires are in good shape can I not just replace the fuse with existing wiring connectors. Thanks
1 Answer Tom, Even though the original wiring is good it is recommended to follow the instructions for installing the part. Read More...
Cheryl May 02, 2013 for Model Number KUDK031TS3 How can I tell if my thermal fuse is bad? My dishwasher just quit working it gets no power at all. I am trying to tell if it would be the door switch or the thermal fuse.
1 Answer Hello Cheryl. You will test for power to and from the fuse. If there is power there, and none coming out of the fuse, replace the fuse on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Tim April 30, 2013 for Model Number MDBH979AWS3 My dishwasher just stopped working after a cycle. No lights or response. I have confirmed it has power and tested the Thermal Fuse. While testing the fuse I heard a relay or something click and when I put everything back together the dishwasher started acting like it was working and then stopped. Control Board?
1 Answer Hello Tim. Based on the information you provided, you will need to order and replace the thermal fuse on the unit. Read More...
B Man March 19, 2013 for Model Number KUDI02CRBS2 Kitchen aid dishwasher KUDI02CRBS2 Dead no response. Power is on. Some lights functioned on panel but now none do. Thermal fuse or bad control board? Thanks
1 Answer Hello B Man. Check and see if there is power to the thermal fuse and if so, and the unit does not work, you will need to order and replace the thermal fuse W10258275 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John B March 14, 2013 for Model Number DUI055XTSQ33 My Whirlpool disherwasher stopped in the rinse cyclee and will not empty. There is power to the unit but none of the control lights will light. Help¡
1 Answer John, You will want to check your thermal fuse W10258275 that is located in the controls of the unit. The thermal fuse should be closed and if open then the thermal fuse will need to be replaced. Read More...
Matt March 03, 2013 for Model Number DU1345XTVB1 my dishwasher will cut off after we trun it on it will be on for only abut 30 sec and then cut off whe ahve to drain it and then try agin to get it to run. sometimes it may take 4 or 5 time of doing this before it will run. thank for your help..
1 Answer Matt, The thermal fuse W10258275 is the least likely issue, at this point. The more likely issue is a faulty key pad on the control panel WPW10142945. If the control board doesn't see a complete circuit from the selection keypad, or sees multiple keypads pressed, it will turn itself off. Read More...
Jomarie February 10, 2013 for Model Number fu2101933 kudw03ctblo My dishwasher will not dry it goes to clean and the dry light wont come on . I tried running it through a light load cycle but it does the same, goes to clean but not dry.
1 Answer Hello Jomarie. You need to test the high limit WP661566 and the heater WPW10082892. They should read closed for continuity. If good, replace the board in the unit. Read More...
Robert February 05, 2013 for Model Number Kitchen-Aide. KUDC25CHSSI sr# FJ3006752 When I go to start my dishwasher it blinks Child=Lock only. I make sure door is closed, but still blinks. On another occasion it would only work on rinse cycle, now child-lock blinks at all times..Thank-You.
1 Answer Hello Robert. Press and hold energy saver dry for 4 seconds and the light should go off on the unit. Read More...
Rmechanic February 03, 2013 for Model Number kudl03fss3 Workin on kitchenaid dishwasher that all lights went out and will not run. There is either a fuse or a thermal cutoff on line voltage coming in I checked for continuity and it is blown. My question is, is it a fuse or thermal cutoff and what is it rated for? Like what amp draw or temperature will it cutoff at?
1 Answer Hello Rmechanic. Yes, W10258275 is the thermal fuse. If it is bad, you need to replace the harness sent with the new fuse. The specs are not listed. Sorry. Read More...