Luke October 10, 2013 for Model Number 66513783K600 I had liquid spill into the control panel. All controls still light up except when I select a cycle, the start button flashes on and off but does not start when I close the door. I have clean the inside control box but it still does not work. Is there a reset or do I need to purchase a replacement part? Thank you for your assistance.
1 Answer Hello Luke. It sounds like the console WPW10137566 is bad and will need to be replaced on the unit. Read More...
Gw October 09, 2013 for Model Number GU2300TVB1 my dishwasher control button seem to be working intermittently if they work at all. mostly the normal wash and most importantly the start button. I suspect the control panel. what do you think?
1 Answer GW, We Agree, your issue is in the keypad / control panel assembly WPW10175347, You'll probably find that you use the normal wash on, and the start keypads most often, and the circuit has become weak and started to fail. Read More...
Steve October 09, 2013 for Model Number 66513742K601 My five year old Kenmore dishwasher, model 665.13742K601, will not start. Four of the "Cycles" buttons, "Pots/Pans", "Normal Wash", "Light Wash", "Fast Wash," light up when pushed but "Smart Wash" and "Quick Rinse" do not light up when pushed. None of the "Options" buttons, including "Start" light up when pushed, but the "Heated Dry" light does come on when one of the four working "Cycles" buttons is pushed. Please let me know what you think the problem is. Thanks.
1 Answer Hello Steve. it sounds like the control panel WP8558209 is bad and will need to be replaced on the unit. Read More...
Lois September 26, 2013 for Model Number MDB7749AWB2 Hi. I have the stainless under the counter Steam Maytag Dish Washer , all the lights come on except start , the dishwasher will not start is it the fuse or the control panel? Thanks for your help , Lois
1 Answer Hello Lois. Based on the informatio nyou provided, it sounds like the control panel is bad. Read More...
Andy September 16, 2013 for Model Number GU2700XTSS0 My Whirlpool Dishwasher power scour light continuously flashes, pressing other function buttons with no response from machine. Tried resetting breaker and pressing other buttons then normal and power scour light flash but no action from machine. I suspect control board. Please help. Thanks Andy
1 Answer Hello Andy. Based on the information you provided, you will need to order and replace the control panel on the unit. Read More...
Jon September 13, 2013 for Model Number 66513742K601 The Thermal Fuse (W10258275) failed. The heating element and the thermostat both checked out fine. What else may have caused the fuse to fail?
1 Answer Jon, A voltage issue (low or high "spike" could cause an issue. Also check and make sure the connections inside the junction box of the dishwasher are good and tight. And of course there is the basic age of the part. As long as there's power to the dishwasher the fuse is active and carrying voltage. Read More...
Driveguy September 10, 2013 for Model Number DU1055XTSS2 The machine stays in the wash cycle of well over an hour in the normal cycle and light cycle. When I run it in the rinse cycle it appears to work properly. I have check the water temp and it is plenty hot. Any suggestions? Driveguy
1 Answer Hello Driveguy. It is normal for the unit to run almost 3 hours during a Normal wash cycle. You could have a bad sensor on the unit causing the issue with the unit. Read More...
Charles M July 10, 2013 for Model Number kuds30ivss4 This kitchenaid dishwasher appears to be running normally after installing new control board (w10285179). There are, however, 3 lights that stay illuminated on the front panel when the unit is not runnning. They are: Heavy Duty, Normal Wash and Light/China. What do you recommend I do to correct this? Many thanks.
1 Answer Hello Charles. It sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Susan June 20, 2013 for Model Number MDBH979AWB2 Problem first began with not being able to turn off heat dry when pressing button. After a few weeks of this, I went to start a load of dishes. The light came on for normal wash, the light came on for heated dry and would not turn off when pressed, and the dishwasher itself wouldn't come on when pressing start (start light wouldn't come on either even though the other two lights were on). The normal and heated wash lights come on now for a few seconds and then shut off. Please advise.
1 Answer Hello Susan. It sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Victor June 01, 2013 for Model Number gu2300xtvs3 Replaced thermal fuse with your part #AP4423189. 18 month old dishwasher still dead. What else could it be?
1 Answer Victor, You will want to make sure that you are getting 120 vac to the control board. If you are getting 120 vac to the control board then check the door switches to make sure that they are good. If they check ok then the control board would be the most likely cause of failure. Read More...