Parts for Ikea IX7DDEXGZ002: Refrigerator Liner Parts

The Water Inlet Valve is an OEM part for Whirlpool side-by-side refrigerators with internal water and ice systems. Located behind the rear panel on the water supply line, it controls water flow into the refrigerator.

Symptoms of a faulty inlet valve include:

• Slow or incomplete fills of the ice maker or water dispenser  
• Intermittent water flow or pressure issues at the dispenser
• Water leaks from around the inlet valve housing 

Causes can be mineral buildup on internal valve parts restricting flow after years of use. Mechanical wear and cracks in the plastic casting may also develop over time.

This OEM replacement is compatible with additional Whirlpool, KitchenAid, and some Kenmore side-by-side refrigerator models.

This wire cover protects and secures the ice maker wiring and harness inside the freezer, helping prevent snagging or damage for reliable ice maker operation. It's a small replacement panel used where wires route to the ice maker assembly. What it does:

• Shields the ice maker wiring harness from contact, abrasion, and accidental disconnection
• Keeps wiring routed neatly to reduce strain and interference with moving parts
• Helps maintain proper clearance between wires and the ice maker or evaporator fan
• Can resolve symptoms like loose or exposed wiring near the ice maker or visible wire routing damage

• One wire cover for the ice maker wiring harness

• Disconnect power to the appliance before accessing the ice maker area
• Remove only the fasteners indicated by your model's service instructions and retain them for reassembly
• Handle plastic parts gently to avoid cracking; align tabs and screw holes before fastening
• If wiring is damaged or connectors are loose, inspect/replace the wiring or connector as needed

A clear replacement interior light lens that protects and diffuses the appliance light for even illumination. Restores proper light coverage and keeps the bulb shielded from spills and debris for safer, brighter interior lighting. What it does:

• Covers and diffuses the interior lamp so light spreads evenly across the compartment
• Protects the bulb from moisture, spills and physical damage
• Replaces cracked, chipped or yellowed lenses that reduce light output or look worn
• Helps prevent direct contact with the bulb for safer operation

• Disconnect power to the appliance before accessing the interior light
• Remove shelves or bins as needed for clear access to the lens
• Lens typically snaps or screws into place; handle gently to avoid cracking
• Use gloves to keep the lens clean and avoid fingerprints; reapply power only after installation is complete

The LED Light Module is an OEM part for Whirlpool refrigerators. It provides illumination inside the refrigerator, ensuring visibility of contents. This module is designed to offer bright, energy-efficient lighting that enhances the user experience and helps in locating items quickly. Housing part number W11684721 may be needed also due to manufacturer design changes.

Common causes of a bad light module include electrical surges, moisture exposure, or wear and tear over time. These issues can lead to the failure of the LED components or circuitry within the module.

Symptoms of a bad LED Light Module include:

• Dim or flickering light inside the refrigerator
• Complete failure of the light to turn on
• Intermittent lighting issues
• The light staying on continuously

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Filter is an OEM part for Whirlpool refrigerators. It is designed to filter and purify the water for your refrigerator, ensuring clean and fresh drinking water and ice.

A bad refrigerator water filter can be caused by regular use and the buildup of contaminants over time. It may also become less effective if not replaced according to the manufacturer's recommended schedule.

Symptoms of a bad refrigerator water filter include:

• A decrease in water flow or water pressure.
• An unpleasant taste or odor in the water.
• The presence of particles or sediment in the water.
• Cloudy or discolored ice cubes.

If you notice any of these signs or if it has been more than six months since your last filter replacement, it's time to replace the refrigerator water filter with this genuine OEM part. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This refrigerator water tube carries fresh water between the valve, filter/reservoir, and the dispenser or ice maker. Replacing a damaged or kinked tube helps restore safe, leak-free water flow and consistent dispensing/ice production.

• Routes water between internal components such as the inlet valve, filter/reservoir, and dispenser/ice maker assemblies
• Typical failure signs: leaks under/behind the refrigerator, slow or no water at the dispenser, reduced or no ice
• Physical damage like cracks, pinholes, or kinks indicates the tube should be replaced
• Proper routing prevents sharp bends that can restrict flow or cause future leaks

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Note original routing; cut tube ends square and fully seat into quick-connect fittings, then tug gently to confirm engagement
• Restore water and power, then check all connections for leaks

The Reservoir is a Whirlpool OEM replacement part for Whirlpool side-by-side refrigerators. This assembly does include the filter head. The filter head connects the external filter cartridge to the internal reservoir. The reservoir holds filtered water that is dispensed from the external door dispenser.

Causes can be normal wear to sealing components, cracks in plastic from repeated pressure changes, or mineral buildup affecting water flow.

Symptoms of a problem include:

• Prematurely lit filter change indicators
• Water dispenser flow slowing or stopping over time
• Gradual decline in ice production amounts
• Noticeable sediment or particles in dispensed water

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Some Kenmore models.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal