Parts for Kitchenaid KRFC604FSS00: 03 - Refrigerator Liner Parts

The Water Inlet Valve is an OEM replacement part for Whirlpool refrigerators. It is responsible for controlling the flow of water into the refrigerator, supplying water to the ice maker and water dispenser.

Symptoms of a need to replace the water inlet valve include:

• No water flow to the ice maker or water dispenser
• Leaks or water puddling near the valve
• The ice maker not producing ice or producing insufficient ice

Causes of a bad water inlet valve can include sediment buildup or clogging, mechanical failures due to age or wear, or electrical malfunctions preventing the valve from opening and closing properly.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This refrigerator water filter housing holds the filter and routes water through it to the dispenser and ice maker. Replace it if the housing is cracked, leaking, or won't engage the filter to help restore consistent water flow. What it does:

• Directs household water through the installed filter to the dispenser and ice maker
• Locks and seals the filter; opens/closes the internal shutoff when the filter is engaged
• Helps maintain proper flow and reduce leaks at the filter connection
• Common failure symptoms may include water dripping from the filter area, the filter not seating or popping out, low/no dispenser flow, or no ice production

• 1 water filter housing assembly

• Unplug the refrigerator and shut off the water supply; dispense water to relieve pressure
• Place a towel under the area to catch residual water
• Remove any cover/bracket as needed; disconnect tubing from quick-connect fittings and note routing/orientation
• Install the new housing, fully seat tubing in the fittings, restore water and power, check for leaks, and flush per your model's instructions

This water tube routes water between the household supply and your appliance's dispenser or ice maker so water flows where it's needed. Replacing a damaged tube restores reliable water delivery and helps prevent leaks. What it does:

• Carries water from the inlet to the dispenser or ice maker assembly
• Prevents leaks when intact; cracks or holes can cause visible drips or puddles
• Supports proper filling of the ice maker and dispensing functions
• Can become brittle or clogged over time, interrupting water flow

• One water tube

• Shut off the household water supply and unplug the appliance before starting
• Inspect and replace any worn clamps or seals when installing the tube
• Route the tube along the original path and check for kinks that could restrict flow
• After installation, restore power and water, then check carefully for leaks

The Whirlpool EveryDrop Ice and Water Refrigerator Filter 2 is an OEM replacement part for Whirlpool refrigerators. This advanced water filter is designed to provide superior filtration for both the ice maker and water dispenser. This water filter effectively reduces numerous contaminants, including lead, pesticides, and pharmaceuticals, ensuring that your drinking water and ice are not only clean but also taste great.  

Regular replacement of the EveryDrop Filter is recommended to maintain optimal performance and water quality. Over time, filters can become clogged with particles and contaminants, leading to reduced water flow and a decline in the effectiveness of filtration.

Symptoms of a filter that needs to be replaced include:

• Noticeable decrease in water flow rate from the dispenser
• Unpleasant taste or odor in the water and ice
• The filter indicator light on the refrigerator turns on

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The FreshFlow Refrigerator Air Filter is an OEM component for Whirlpool and Maytag refrigerators. Located inside the ventilation system, this filter purifies circulated air. This air filter is 3" wide by 2" high and white in color. It should be replaced every 6 months to ensure the best performance.

Causes of failure relate to clogging from trapped dust, dander and other allergens despite regular replacement intervals. Performance decreases as filter media becomes saturated over months of use.  

Symptoms of a dirty or blocked refrigerator air filter include:

• Reduced airflow causes higher compressor runtime hours  
• Odors being pulled into the fridge from unfiltered vents  
• Shortening of food storage life due to unpurified air exposure
• Reduced fan speeds or strange noises originating from the vents

This genuine Whirlpool filter is also compatible with Maytag, Jenn-Air, and Amana models as well.

The Bracket is an OEM part for Whirlpool refrigerators. It securely holds the water filter in place, ensuring a tight seal and proper filtration of your refrigerator's water supply.

A bad water filter bracket can occur due to wear and tear, damage, or improper installation. If you notice symptoms such as a loose or misaligned water filter, water leakage around the filter area, or a decrease in water quality, it may be time to replace the water filter bracket.

Symptoms of a bad water filter bracket include:

• Loose or misaligned water filter
• Water leakage around the filter area
• Decrease in water quality or taste

Repair your refrigerator's water filtration system by replacing the faulty or damaged water filter bracket with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement screw fastens trim, panels and small components to restore secure attachment and reduce rattling or movement. Use when a screw is missing, stripped, or damaged to keep parts aligned and operating quietly. What it does:

• Secures panels, brackets and trim to appliance assemblies
• Prevents vibration, rattling and misalignment caused by missing or damaged fasteners
• Replaces lost or stripped screws that can allow gaps or loose parts
• Helps maintain safe, stable operation by keeping components properly fastened

• Disconnect power (and water if applicable) before accessing interior panels
• Use the proper screwdriver or driver bit to avoid stripping the head
• Align parts before tightening and tighten until snug—do not overtighten
• Replace only with the correct OEM part to ensure proper fit and function

The Cap Filter is an OEM component for Whirlpool refrigerators. Located inside the back of the fresh food compartment, it helps maintain optimal indoor air quality by capturing household odors and gases.  

The precision-woven filter media effectively removes ethylene and other contaminants from circulating air without slowing airflow. Its secure mounting design installs and removes easily without tools for periodic replacement.

Causes of a faulty cap filter include clogging from accumulated particles or moisture remaining trapped over time, which reduces effectiveness.

Symptoms of a bad cap filter can include: 

• Lingering odors inside the refrigerator  
• Fresher items absorb smells faster than usual
• Decreased airflow causing warmer temperatures
• Small pieces of filter shedding inside

Replace yours today with this genuine Whirlpool filter to restore maximum odor protection. Compatible with many Kenmore, Maytag, Jenn-Air, and KitchenAid models.

The Evaporator Cover is an OEM part for Whirlpool refrigerators. It protects and covers the evaporator coil, preventing frost buildup, ensuring proper cooling, and efficient operation of the refrigerator.

A bad evaporator cover can occur due to damage, wear and tear, or clogging. If you notice symptoms such as poor cooling, excessive frost accumulation, or unusual noises coming from the refrigerator, it may indicate a faulty or damaged evaporator cover.

Symptoms of a bad evaporator cover assembly include:

• Poor cooling performance
• Excessive frost buildup
• Unusual noises coming from the refrigerator

Restore your refrigerator by replacing the faulty evaporator cover with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This wire harness routes power and signals between a dryer's control and components for reliable operation. It replaces damaged or frayed wiring to restore proper electrical connections and help eliminate intermittent faults. What it does

• Provides the factory wiring connections between control, motor, heating and safety components
• Restores lost or intermittent power caused by broken, burned, or corroded wires/connectors
• Prevents arcing and shorts when old wiring shows visible damage
• Ensures correct signal routing for controls and safety switches

• One complete wire harness assembly as shown

• Always disconnect power (unplug or shut off breaker) before starting service
• Route harness away from sharp edges and heat sources; secure with existing clips or ties
• Replace terminals or connectors that are melted or damaged to avoid future failures

Size: 8 x 1-1/4 inch.

This heater is the dryer heating element assembly that warms air used to dry clothes, restoring normal drying performance when the original element fails. Designed to replace a worn or broken dryer heater. What it does:

• Heats air circulated through the drum so laundry dries efficiently
• Replaces a burnt-out or open heating element that causes no-heat or reduced-heat symptoms
• Helps resolve long dry times or loads that remain damp after a full cycle
• Works with the dryer's thermal cutoff and thermostat to maintain operating temperature

• Disconnect power to the appliance before attempting service to avoid shock or injury
• Handle the element gently to avoid bending or damaging heating coils
• If other temperature-safety parts (thermal fuses/thermostats) show damage, inspect and replace as needed

This replacement sleeve is a small plastic insert that protects and guides a rotating or sliding shaft on the appliance, helping restore smooth movement and reduce wear. It's a simple, low-cost part that prevents metal-on-metal contact. What it does:

• Guides and centers a shaft or pin to keep moving parts aligned
• Protects metal components from wear and abrasion
• Reduces noise and vibration caused by loose or worn interfaces
• Helps restore proper movement when sleeves are cracked, split, or excessively worn

• One replacement sleeve

• Disconnect power (and water, if applicable) before starting any repair
• Remove surrounding components as needed to access the sleeve; use basic hand tools
• Inspect mating parts and replace or clean if damaged; do not force a damaged sleeve into place