Maytag Washer LAW9400ABL Leaking

The Injector Valve is an OEM replacement part specific to Whirlpool washing machines. It plays an important role in properly dispensing detergent into the wash load. Located inside the detergent dispenser drawer, the injector valve regulates the flow of water at timed intervals to fully dissolve and evenly distribute detergent among clothes. Washer air gap rubber injector. For the injector nozzle order WP213015. For a kit that includes the injector valve, nozzle, and two clamps order 12001677

Causes of a bad injector valve can include clogging from mineral deposits or debris, wear and tear from regular use, or damage from high water pressure. A malfunctioning injector valve can lead to improper water levels and affect the washing machine's performance.

Symptoms of a bad injector valve include:

• Inadequate water filling the washer
• Water leaks around the valve area
• Unusual noises during the water filling cycle
• The washer not advancing through cycles properly
• Visible debris or deposits at the injector valve opening

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washers.

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Washer leaking during fill? A cracked or clogged injector nozzle is often the culprit. This part directs water into the tub. Simple 20-minute DIY fix.

The Water Inlet Valve is an OEM replacement part for Whirlpool washing machines. It is responsible for controlling the flow of water into the washer tub, ensuring the proper water level and supply for each wash cycle.

Causes of a bad water inlet valve can include sediment buildup or obstructions, electrical malfunctions, or normal wear and tear over time, leading to valve failure or improper operation.

Symptoms of a faulty water inlet valve include:

• The washer not filling with water or filling slowly
• Incorrect or inconsistent water levels during wash cycles
• Water leaks around the valve or inlet area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

The Siphon Break is an OEM part for Whirlpool washing machines. It is a critical safety component that prevents the backflow of contaminated water from the washer into the fresh water supply line. For the gasket use part number [AP6005834], For the siphon elbow use part number [AP4024083]

Causes of a faulty siphon break include physical damage, clogging due to mineral buildup or debris, or general wear and tear over time.

Symptoms of a bad siphon break:

• Water leaks or puddles around the washing machine
• The washer not filling with water properly
• Potential for contaminated water to enter the fresh water supply

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

Fix water leaking from under your washer lid during fill. This inlet sleeve connects the fill valve to the nozzle. Easy 30-minute DIY repair for wet floors.

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the tub to the pump, allowing water to drain from the tub during the washing and rinsing cycles. It is designed to handle the water flow and pressure within the washer, ensuring efficient drainage.

Causes of a bad tub to pump hose can include wear and tear over time, exposure to harsh chemicals or debris, or damage due to accidental punctures or kinks. When the hose is compromised, it can lead to drainage issues and potential water leaks.

Symptoms of a bad tub to pump hose include:

• Water not draining from the washer
•  Leaks or puddles underneath the washer
• Visible cracks or wear on the hose
• Error codes related to drainage problems

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Secures water and drain hoses in washers to prevent leaks. Replace if connections loosen or clamp shows corrosion. Confirm fit with your model number.

Secures washing machine hoses to prevent leaks in the water system. Replace if damaged, corroded, or connections are loose. Verify fit by part number.

For complete assembly order WP206680.

For complete assembly order WP206680.

Seals the water injector connection in your washer to prevent leaks and frost buildup. Replace if you notice water leaking or moisture around the inlet area. Confirm fit with your model number.

The Drain Hose is an OEM part for Whirlpool washing machines. It is responsible for carrying wastewater from the washing machine to the household drain system, ensuring proper removal of water during and after the wash cycle.

Common causes of a bad drain hose include wear and tear over time, blockages from debris or lint, and damage from sharp objects or improper installation.

Symptoms of a bad Drain Hose include:

• Water leaks from the hose
• Slow or incomplete drainage
• Visible cracks, splits, or punctures
• Unpleasant odors from trapped debris

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This siphon break elbow is a 90-degree connector used in the drain path to create an air break that helps prevent back-siphoning. Replacing a cracked or obstructed elbow can stop leaks and restore proper draining performance.

• Provides a 90-degree connection between the drain hose and the siphon break/air-gap fitting
• Maintains the atmospheric break that prevents wastewater from siphoning back into the appliance
• Helps route drain flow without kinking or stressing the hose
• Common symptoms: leaking at the elbow area, water backing up through the drain line, slow or incomplete draining, visible cracks or damage

• Disconnect power; turn off water supply if applicable
• Expect residual water—protect the area with towels or a pan
• Release hose clamps, note orientation, fully seat hoses on the new elbow, and secure clamps
• Run a test and check for leaks

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

Secures hose connections to prevent leaks in your washer. Replace if you notice dripping at hose fittings or loose connections. Verify fit with your model.

This replacement hose carries liquid bleach from the dispenser into the washer tub. Restores proper dispensing and helps prevent leaks or splashes when the original hose becomes brittle, cracked, or loose.

• Routes bleach from the dispenser funnel to the outer tub during the cycle
• Helps keep bleach off the top panel, wiring, and cabinet surfaces
• Symptoms include leaks near the dispenser area, bleach left in the cup, or a strong bleach odor inside the cabinet
• Visible cracking, hardening, or splits on the hose are common failure signs

• Disconnect power and turn off water supply before servicing
• Access the dispenser area; place a towel to catch residual liquid
• Note hose routing and orientation; release clamps and transfer/reuse them as needed
• Fully seat the hose on both fittings, secure with clamps, and test for leaks after reassembly

Secures hoses to fittings and prevents leaks in your washer. Replace if worn, loose, or missing to stop drips and keep water connections tight. Confirm fit.

This gasket creates a reliable seal between two appliance components. Replacing a worn or damaged gasket helps stop leaks and drafts at the joint, restoring proper performance and preventing moisture, frost, or debris from entering where parts meet.

• Forms a tight seal between mating surfaces to help prevent water or air leaks
• Helps maintain proper temperatures and operation by keeping unwanted air or moisture out
• Reduces vibration at the joint that can cause noise or loosening over time
• Typical failure signs: visible cracks or flattening, seepage or drips at the joint, moisture or frost forming nearby

• Disconnect power and shut off water supply before service
• Photograph the original setup to aid reassembly
• Remove the old gasket and thoroughly clean/dry both mating surfaces; remove any residue
• Seat the new gasket evenly without stretching; tighten fasteners evenly and check for leaks or air gaps after reassembly

Small metal clip that secures panels, brackets, or tubing in place inside appliances. Replace if bent, fatigued, or missing to restore secure mounting.

Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

This agitator seal assembly sits at the agitator/drive-shaft pass-through to keep wash water inside the tub and away from the drive system. Replacing a worn seal helps stop center-post leaks and protects internal components from moisture.

• Seals the opening where the agitator/drive shaft passes through the tub or centerpost
• Helps prevent water from migrating into the centerpost/gearcase area
• Supports reliable agitation and spin by keeping contaminants out of the drive assembly
• Common symptoms of failure: water leaking from the center of the tub or beneath the washer, or rust/water tracks around the agitator hub

• Disconnect power and shut off water; wear gloves and eye protection
• Remove agitator cap and fastener, then lift the agitator to access the seal (procedure varies by model)
• Note the original seal orientation; clean mating surfaces and install the new seal squarely (lightly lubricate only if specified by the manufacturer)
• Reassemble and run a short fill/agitate test while observing for leaks